Cisco Catalyst 1000.pdf
2.9 MB
Cisco Catalyst 1000 - Новая линейка коммутаторов
datasheet: https://www.cisco.com/c/en/us/products/collateral/switches/catalyst-1000-series-switches/nb-06-cat1k-ser-switch-ds-cte-en.html
#cisco
datasheet: https://www.cisco.com/c/en/us/products/collateral/switches/catalyst-1000-series-switches/nb-06-cat1k-ser-switch-ds-cte-en.html
#cisco
cisco_converter_to_C9K.xlsx
316.2 KB
Конвертер для быстрого поиска замены EoS\EoL оборудования серии c2960, c3650, c3850 на новую линейку C9000
#cisco
#cisco
Cisco Wireless 2021.10.pdf
3.6 MB
Рекомендации по установке уличных wif точек доступа cisco
https://www.cisco.com/c/en/us/td/docs/wireless/access_point/outdoor/video/ap-best-practices.html
#cisco #wifi
https://www.cisco.com/c/en/us/td/docs/wireless/access_point/outdoor/video/ap-best-practices.html
#cisco #wifi
Cisco
Video Series: Best Practices for Installing Outdoor Wireless Access Points
This video series outlines the various best practices to be followed and common pitfalls to be avoided while installing outdoor wireless access points.
WiFi точки перестали регистрироваться на Cisco WLC контроллере DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c
Ошибка:
Решение для версии 7.0.252.0:
Ошибка:
%DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:XXXX Failed to complete DTLS handshake with peer
Проблема кроется в истекшем сроке действия сертификата (MIC) зашитого в точку на заводе изготовителеРешение для версии 7.0.252.0:
config ap lifetime-check mic enableРешение для версии 7.4.140.0 и более новых:
config ap cert-expiry-ignore mic enable#cisco #wifi
Настройка EtherChannels между Cisco ASA (Failover Active-Standby) и L3 switches (StackWise/VSS/vPC)
If you use the ASA in an Active/Standby failover deployment, then you need to create separate EtherChannels on the switches in the StackWise/VSS/vPC, one for each ASA. On each ASA, a single EtherChannel connects to both switches. Even if you could group all switch interfaces into a single EtherChannel connecting to both ASA (in this case, the EtherChannel will not be established because of the separate ASA system IDs), a single EtherChannel would not be desirable because you do not want traffic sent to the standby ASA
Т.о создаем на коммутаторах для каждой Cisco ASA свой PortChannel согласно рисунку
#cisco #asa #network
If you use the ASA in an Active/Standby failover deployment, then you need to create separate EtherChannels on the switches in the StackWise/VSS/vPC, one for each ASA. On each ASA, a single EtherChannel connects to both switches. Even if you could group all switch interfaces into a single EtherChannel connecting to both ASA (in this case, the EtherChannel will not be established because of the separate ASA system IDs), a single EtherChannel would not be desirable because you do not want traffic sent to the standby ASA
Т.о создаем на коммутаторах для каждой Cisco ASA свой PortChannel согласно рисунку
#cisco #asa #network
Syslog configure on network equipment
HP / HUAWEI:
HP / HUAWEI:
info-center enableQTECH:
undo info-center logfile enable
info-center source default channel 2 log level warnings
info-center source default channel 4 log level warnings
info-center loghost 10.10.10.10
info-center timestamp loghost no-year-date
logging 10.10.10.10 level warningsCISCO:
logging onARUBA:
logging origin-id hostname
logging host 10.10.10.10
logging history warnings
logging buffered warnings
logging trap warnings
logging 10.10.10.10ZYXEL:
logging origin-id hostname
logging severity warning
syslog#network #cisco
syslog type system
syslog type interface
syslog type switch
syslog type aaa
syslog type ip
syslog type system facility 7
syslog type interface facility 7
syslog type switch facility 7
syslog type aaa facility 7
syslog type ip facility 7
syslog server 10.10.10.10 level 6