GPS MODULE NEO-7M
- GPS modules NEO-7M, 3V-5V power supply
- Interface features :TTL level compatible with 3.3V/ 5V systems;
- Reception characteristics : 56 channels , GPS L1 (1575.42Mhz) C/A code , SBAS:WAAS / EGNOS / MSAS;
- Positioning accuracy : 2.5mCEP (SBAS: 2.0mCEP)
- Update rate :Maximum 10Hz ( default 1HZ)
- Acquisition Time : Cold start : 27S ( fastest ),Hot start : 1S
- Tracking Sensitivity : -162dBm
- Acquisition sensitivity ( cold start ): -148dBm
- Oscillator : TCXO (+/- 0.5PPM)
- Communication Protocol : NMEA ( default ) / UBX Binary
- Serial communication baud rate : 9600
- Speed limit : 500m / s
- Height restriction : 50000m
- Supports GLONASS ( Russian navigation system );
- Come with IPX interface, you can connect many other active antenna;
- Built- in rechargeable backup battery , can be powered down to save ephemeris data to achieve hot start;
- Operating voltage : 2.7V-5.0V (VCC pin input )
- Working Current : 35mA
Price 1250 Birr
https://vector4engineering.com/product/gps-module/
- GPS modules NEO-7M, 3V-5V power supply
- Interface features :TTL level compatible with 3.3V/ 5V systems;
- Reception characteristics : 56 channels , GPS L1 (1575.42Mhz) C/A code , SBAS:WAAS / EGNOS / MSAS;
- Positioning accuracy : 2.5mCEP (SBAS: 2.0mCEP)
- Update rate :Maximum 10Hz ( default 1HZ)
- Acquisition Time : Cold start : 27S ( fastest ),Hot start : 1S
- Tracking Sensitivity : -162dBm
- Acquisition sensitivity ( cold start ): -148dBm
- Oscillator : TCXO (+/- 0.5PPM)
- Communication Protocol : NMEA ( default ) / UBX Binary
- Serial communication baud rate : 9600
- Speed limit : 500m / s
- Height restriction : 50000m
- Supports GLONASS ( Russian navigation system );
- Come with IPX interface, you can connect many other active antenna;
- Built- in rechargeable backup battery , can be powered down to save ephemeris data to achieve hot start;
- Operating voltage : 2.7V-5.0V (VCC pin input )
- Working Current : 35mA
Price 1250 Birr
https://vector4engineering.com/product/gps-module/
Infrared Temperature Sensor GY-906 MLX90614 is an infrared thermometer for non-contact temperature measurements. It can use with any microcontroller that can communicate with it through it's I2C interface.
- Easy to integrate
- Mounted on a breakout board with two types of pins
- 10k Pull up resistors for the I2C interface with optional solder jumpers
- Factory calibrated in temperature range:
-40+125°C for sensor temperature
-70+380°C for object temperature
- High accuracy of 0.5°C over wide temperature range (+50°C for both) High (medical) accuracy calibration
- Measurement resolution of 0.02°C
- Single and dual zone versions
- SMBus compatible digital interface
- Customizable PWM output for continuous reading.
Price 2000
Address Megenagna Zefmesh Grandmall 3rd floor 301
https://vector4engineering.com/product/mlx90614-non-contact-infrared-temperature/
0922787347/0924468599
- Easy to integrate
- Mounted on a breakout board with two types of pins
- 10k Pull up resistors for the I2C interface with optional solder jumpers
- Factory calibrated in temperature range:
-40+125°C for sensor temperature
-70+380°C for object temperature
- High accuracy of 0.5°C over wide temperature range (+50°C for both) High (medical) accuracy calibration
- Measurement resolution of 0.02°C
- Single and dual zone versions
- SMBus compatible digital interface
- Customizable PWM output for continuous reading.
Price 2000
Address Megenagna Zefmesh Grandmall 3rd floor 301
https://vector4engineering.com/product/mlx90614-non-contact-infrared-temperature/
0922787347/0924468599
CREALITY 24V 4010 AXIAL FAN
- Fan type : Axial Fan
- Operating Voltage : 24V
- Operating current : 0.1A
- Dimensions : 40 x 40 x 10mm
- These 4010 Axial Fans are designed and stocked specifically for the Ender 3 and CR-20, and have been designed with the 24V supply in mind to accommodate the unique voltages that the Ender 3 utilises.
- Fit for Ender-3、Ender-3 Pro、Ender-3S、Ender-3 v2、Ender-3 Max、Ender-5、Ender-5s、Ender-5 Pro、 Ender—5 Plus、Ender_6、CR-5 Pro H、CR-X、CR-X Pro、CR-6 SE、CR-6 Max、CR-30 (Installation Position for Nozzle)
Price 950 Birr
https://vector4engineering.com/product/axial-fan/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
- Fan type : Axial Fan
- Operating Voltage : 24V
- Operating current : 0.1A
- Dimensions : 40 x 40 x 10mm
- These 4010 Axial Fans are designed and stocked specifically for the Ender 3 and CR-20, and have been designed with the 24V supply in mind to accommodate the unique voltages that the Ender 3 utilises.
- Fit for Ender-3、Ender-3 Pro、Ender-3S、Ender-3 v2、Ender-3 Max、Ender-5、Ender-5s、Ender-5 Pro、 Ender—5 Plus、Ender_6、CR-5 Pro H、CR-X、CR-X Pro、CR-6 SE、CR-6 Max、CR-30 (Installation Position for Nozzle)
Price 950 Birr
https://vector4engineering.com/product/axial-fan/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
CREALITY MK8 EXTRUDER PARTS
- Model: MK8 extruder parts
- Color: silver
- Material: aluminum alloy
- Suitable consumables: 1.75mm
- The full metal aluminum alloy extruder kit suitable for almost all Creality’s 3D Printers except CR-X and CR-10S Pro.
- It’s a perfect replacement for Ender 3, Ender 3 Pro, Ender 3 V2, Ender 5, CR-7, CR-8, CR-10 Series, CR-10 S4, CR-10 S5, CR-10 Mini, CR-10S, CR-10 Plus
Package Includes:
MK8 extruder metal block*2
Spring*1
Screw *7
Spring*1
Pneumatic connector*1
Buckle*1
Gear*1
Bearing*1
Pin*2
Price 2500 Birr
https://vector4engineering.com/product/extruder-parts/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
- Model: MK8 extruder parts
- Color: silver
- Material: aluminum alloy
- Suitable consumables: 1.75mm
- The full metal aluminum alloy extruder kit suitable for almost all Creality’s 3D Printers except CR-X and CR-10S Pro.
- It’s a perfect replacement for Ender 3, Ender 3 Pro, Ender 3 V2, Ender 5, CR-7, CR-8, CR-10 Series, CR-10 S4, CR-10 S5, CR-10 Mini, CR-10S, CR-10 Plus
Package Includes:
MK8 extruder metal block*2
Spring*1
Screw *7
Spring*1
Pneumatic connector*1
Buckle*1
Gear*1
Bearing*1
Pin*2
Price 2500 Birr
https://vector4engineering.com/product/extruder-parts/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
CREALITY 24V 4010 BLOWER FAN
- Fan type : Brushless Blower Fan
- Bearing type : oil bearing
- Operating Voltage : 24V
- Operating current : 0.1A
- Dimensions : 40 x 40 x 10mm
- Fit for Ender-3、Ender-3 Pro、Ender-3S、Ender-3 v2、Ender-3 Max、Ender-5、Ender-5s、Ender-5 Pro、 Ender—5 Plus、Ender_6、CR-5 Pro H、CR-X、CR-X Pro、CR-6 SE、CR-6 Max、CR-30 (Installation Position for Nozzle)
Price 500 Birr
https://vector4engineering.com/product/blower-fan/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
- Fan type : Brushless Blower Fan
- Bearing type : oil bearing
- Operating Voltage : 24V
- Operating current : 0.1A
- Dimensions : 40 x 40 x 10mm
- Fit for Ender-3、Ender-3 Pro、Ender-3S、Ender-3 v2、Ender-3 Max、Ender-5、Ender-5s、Ender-5 Pro、 Ender—5 Plus、Ender_6、CR-5 Pro H、CR-X、CR-X Pro、CR-6 SE、CR-6 Max、CR-30 (Installation Position for Nozzle)
Price 500 Birr
https://vector4engineering.com/product/blower-fan/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
ARDUINO NANO EXPANSION SHIELD
- It is a perfect companion of Nano breadboard and compatible with both Nano v2.x and v3.x.
- After soldering the additional pins on the outside of the board, we get a clone of the Arduino UNO board (the same pins and contacts)
- The module has made the pins of all the contacts of the Arduino plates and additionally 12V power socket with 5V power adapter
- RESET button
- Shield has a standard 2.54mm raster – practically all electronic devices fit them (integrated circuits, passive elements, plugs, etc.)
- Proto shield has 2 buttons and 2 LEDs that can be used in any way.
- The board allows access to all Arduino pins.
- Dimensions: 70x54mm
14 I / O Pin (Servo Type with GND, Power and Signal)
8 analog and GND
6 PWM
1 servo power input
I2C output
3.3V output
Price 450 Birr
https://vector4engineering.com/product/nano-shield/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
- It is a perfect companion of Nano breadboard and compatible with both Nano v2.x and v3.x.
- After soldering the additional pins on the outside of the board, we get a clone of the Arduino UNO board (the same pins and contacts)
- The module has made the pins of all the contacts of the Arduino plates and additionally 12V power socket with 5V power adapter
- RESET button
- Shield has a standard 2.54mm raster – practically all electronic devices fit them (integrated circuits, passive elements, plugs, etc.)
- Proto shield has 2 buttons and 2 LEDs that can be used in any way.
- The board allows access to all Arduino pins.
- Dimensions: 70x54mm
14 I / O Pin (Servo Type with GND, Power and Signal)
8 analog and GND
6 PWM
1 servo power input
I2C output
3.3V output
Price 450 Birr
https://vector4engineering.com/product/nano-shield/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
PRESSURE SENSOR MPX10DP
- Series : MPX10
- Pressure type : Differential
- Operating pressure : 1.45 PSI
- Port size : Male, 0.194″ (4.9276mm) Tube, Dual
- Output : 0 ~ 35mV
- Voltage supply : 3V
- Termination Style : PCB
- Operating temperature : -40°C ~ 125°C
Price 1500 Birr
https://vector4engineering.com/product/mpx10dp/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
- Series : MPX10
- Pressure type : Differential
- Operating pressure : 1.45 PSI
- Port size : Male, 0.194″ (4.9276mm) Tube, Dual
- Output : 0 ~ 35mV
- Voltage supply : 3V
- Termination Style : PCB
- Operating temperature : -40°C ~ 125°C
Price 1500 Birr
https://vector4engineering.com/product/mpx10dp/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
MACH3 USB INTERFACE BOARD
- Supports 4-axis linkage, you can connect four stepper motor drives or servo drives
- Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor
- Supports automatic probe tool
- Supports Emergency input
- Supports limit switch
- Supports electronic handwheel
- Provides up to 12 digital signal inputs
Interference design, imported industrial components, high reliability
- Needs use external 24V DC power supply to isolate USB and external port, and to make the system more stable
- Has 0-10V output port, you can use mach3 software to control the spindle motor speed.
- 4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps and other device
Price 5500 Birr
https://vector4engineering.com/product/mach3-usb/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
- Supports 4-axis linkage, you can connect four stepper motor drives or servo drives
- Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor
- Supports automatic probe tool
- Supports Emergency input
- Supports limit switch
- Supports electronic handwheel
- Provides up to 12 digital signal inputs
Interference design, imported industrial components, high reliability
- Needs use external 24V DC power supply to isolate USB and external port, and to make the system more stable
- Has 0-10V output port, you can use mach3 software to control the spindle motor speed.
- 4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps and other device
Price 5500 Birr
https://vector4engineering.com/product/mach3-usb/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
This media is not supported in your browser
VIEW IN TELEGRAM
4×5 KEYPAD
- 4×5 Keys Matrix Array 20 Key Keypad Membrane Switch Control Panel
- Panel size: 75* 85mm
- Length: 18cm
- Insulation Resistance：100M Ω 100V.
- Withstand Voltage：250V Rms.(50-60Hz lmin)
Price 650 Birr
https://vector4engineering.com/product/4x5-keypad/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
- 4×5 Keys Matrix Array 20 Key Keypad Membrane Switch Control Panel
- Panel size: 75* 85mm
- Length: 18cm
- Insulation Resistance：100M Ω 100V.
- Withstand Voltage：250V Rms.(50-60Hz lmin)
Price 650 Birr
https://vector4engineering.com/product/4x5-keypad/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
FERRIC CHLORIDE
- When dissolved in water, iron(III) chloride undergoes hydrolysis and gives off heat in an exothermic reaction. The resulting brown, acidic, and corrosive solution is used as an etchant for copper-based metals in printed circuit boards. Anhydrous iron(III) chloride is a fairly strong Lewis acid, and it is used as a catalyst in organic synthesis.
- 500 gram per pack
Price 850 Birr per 125 gram
Price 3100 Birr per 500 gram
https://vector4engineering.com/product/ferric-chloride/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
- When dissolved in water, iron(III) chloride undergoes hydrolysis and gives off heat in an exothermic reaction. The resulting brown, acidic, and corrosive solution is used as an etchant for copper-based metals in printed circuit boards. Anhydrous iron(III) chloride is a fairly strong Lewis acid, and it is used as a catalyst in organic synthesis.
- 500 gram per pack
Price 850 Birr per 125 gram
Price 3100 Birr per 500 gram
https://vector4engineering.com/product/ferric-chloride/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
OSCILLOSCOPE PROBE P6000
- P6000 For DC 100MHz x1 x10 600V
- Bandwidth: a 100 MHz
- Increase time: 3.5ns
- Attenuation rates: 1X and 10X
- Type resitance: 1X: 1m ohm /- 2%,10 times: 10m ohm /- 2% of
- Input capacity: 1X : 70pf ~ 120pf 10 times: 13pf ~ 17pf
- Maximum input:1X: 200 operating voltage (VP – P)
- 10 times 600 working voltage (VP- P)
- The coverage: 10 ~ 35pf
- Length: the 120 & plusmn, 2cm
- Weight:about 55g
Price 1500 Birr
https://vector4engineering.com/product/oscilloscope-p6000/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
- P6000 For DC 100MHz x1 x10 600V
- Bandwidth: a 100 MHz
- Increase time: 3.5ns
- Attenuation rates: 1X and 10X
- Type resitance: 1X: 1m ohm /- 2%,10 times: 10m ohm /- 2% of
- Input capacity: 1X : 70pf ~ 120pf 10 times: 13pf ~ 17pf
- Maximum input:1X: 200 operating voltage (VP – P)
- 10 times 600 working voltage (VP- P)
- The coverage: 10 ~ 35pf
- Length: the 120 & plusmn, 2cm
- Weight:about 55g
Price 1500 Birr
https://vector4engineering.com/product/oscilloscope-p6000/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
FLEX SENSOR 4.5 INCH
- Angle Displacement Measurement
- Bends and Flexes physically with motion device
- Temperature Range: -35°C to +80°C
- Flat Resistance: 25K Ohms ±30%
- Bend Resistance: minimum 2 times greater than the flat resistance at 180° pinch bend
- Power Rating : 0.5 Watts continuous; 1 Watt Peak
Price 3500 Birr
https://vector4engineering.com/product/flex-4-5-inch/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
- Angle Displacement Measurement
- Bends and Flexes physically with motion device
- Temperature Range: -35°C to +80°C
- Flat Resistance: 25K Ohms ±30%
- Bend Resistance: minimum 2 times greater than the flat resistance at 180° pinch bend
- Power Rating : 0.5 Watts continuous; 1 Watt Peak
Price 3500 Birr
https://vector4engineering.com/product/flex-4-5-inch/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
Vector Four Enginnering/Arduino Shop/ Electronics Supermarket
MULTIMETER TEST LEADS – PROBES - 1 Pair 1000V 10A Needle Tip Probe for Universal Digital Multimeter Test Leads Pin Wire Pen Cable 80cm - Probe Color: Gilded - Sharp contact end - Compatible with universal multimeters - Maximum current : 10A - Test voltage…
MULTIMETER TEST LEADS – PROBES
- 1 Pair 1000V 10A Needle Tip Probe for Universal Digital Multimeter Test Leads Pin Wire Pen Cable 80cm
- Probe Color: Gilded
- Sharp contact end
- Compatible with universal multimeters
- Maximum current : 10A
- Test voltage range: 1000V Max
- Cable length: 80cm
- Cat III 1000V copper coated custom painted.
- Reinforced by Silicon Anti-break
- Anti-burn and heat resistant
- Suit for testing IC components
Price 380 Birr
https://vector4engineering.com/product/multimeter-test-leads-probes/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0922787347 Kase/0924468599 Haben
VECTOR FOUR ENGINEERING
- 1 Pair 1000V 10A Needle Tip Probe for Universal Digital Multimeter Test Leads Pin Wire Pen Cable 80cm
- Probe Color: Gilded
- Sharp contact end
- Compatible with universal multimeters
- Maximum current : 10A
- Test voltage range: 1000V Max
- Cable length: 80cm
- Cat III 1000V copper coated custom painted.
- Reinforced by Silicon Anti-break
- Anti-burn and heat resistant
- Suit for testing IC components
Price 380 Birr
https://vector4engineering.com/product/multimeter-test-leads-probes/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0922787347 Kase/0924468599 Haben
VECTOR FOUR ENGINEERING
DC VOLTAGE TRANSCDUCER
- Model: NV3-DV-V7-P2-o4
- Power: 12VDC
- Input voltage: 0 – 70VDC
- Output: 4 – 20mA
- Load capacity: 270 ohm
- NV3 series DC transducer transforms the measured signal to a voltage output through the HCNR200/201/linearity photodiode, which is in excellent linear relations with while completely isolated to the original one, with the CAD and the concise circuitry, the device is in high stability and wasy to install.
Price 1750 birr
https://vector4engineering.com/product/dc-voltage-transcducer/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0922787347 Kase/0924468599 Haben
VECTOR FOUR ENGINEERING
- Model: NV3-DV-V7-P2-o4
- Power: 12VDC
- Input voltage: 0 – 70VDC
- Output: 4 – 20mA
- Load capacity: 270 ohm
- NV3 series DC transducer transforms the measured signal to a voltage output through the HCNR200/201/linearity photodiode, which is in excellent linear relations with while completely isolated to the original one, with the CAD and the concise circuitry, the device is in high stability and wasy to install.
Price 1750 birr
https://vector4engineering.com/product/dc-voltage-transcducer/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0922787347 Kase/0924468599 Haben
VECTOR FOUR ENGINEERING
12V 2 CHANNEL RECEIVER MODULE
- Input: DC12V
- 2 Channel
- Frequency: 315MHz/433.92MHz
- Remote Control Switch Relay Receiver Module
- Transmitting distance: around 50 m ( open space)
- Button: 4 Buttons
- Modulation System: ASK
- Matching Mode: Intelligent Learning code
- Output terminal: NO , NC , COM
- Size: 68.2*48.2mm
Price 750 Birr
https://vector4engineering.com/product/12v-2-channel-receiver-module/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
- Input: DC12V
- 2 Channel
- Frequency: 315MHz/433.92MHz
- Remote Control Switch Relay Receiver Module
- Transmitting distance: around 50 m ( open space)
- Button: 4 Buttons
- Modulation System: ASK
- Matching Mode: Intelligent Learning code
- Output terminal: NO , NC , COM
- Size: 68.2*48.2mm
Price 750 Birr
https://vector4engineering.com/product/12v-2-channel-receiver-module/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
IOT (internet of things) training for all high school🏢 and campus students🏭.
What is IOT ?🤔
🤗The Internet of Things (IoT) primarily refers to any device🚧, appliance, instrument, or machine🕹 that can connect to the internet🖥. They contain sensors🔋, software, and other technologies used to link and exchange data between systems and devices over the Internet💻.
🗺ADISS ABABA, BOLE, Bora kids mall
To register call us today
📲+251972086868
📩 natnaelbehaylu6@gmail.com
What is IOT ?🤔
🤗The Internet of Things (IoT) primarily refers to any device🚧, appliance, instrument, or machine🕹 that can connect to the internet🖥. They contain sensors🔋, software, and other technologies used to link and exchange data between systems and devices over the Internet💻.
🗺ADISS ABABA, BOLE, Bora kids mall
To register call us today
📲+251972086868
📩 natnaelbehaylu6@gmail.com
LINEAR RAIL 35mm
- 35mm linear guide rail 1.5m long star linear guide
Applications:
CNC Precision machining
Heavy cutting machine
Punching machines
Marble cutting machines
Automatic equipment
Grinding machines
High speed transfer equipments
Injection moulding machines
Package Includes
1.5 meter Rail – 1
HG35 Bearing block – 1
Price 20,500 Birr
https://vector4engineering.com/product/rail-35mm/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
- 35mm linear guide rail 1.5m long star linear guide
Applications:
CNC Precision machining
Heavy cutting machine
Punching machines
Marble cutting machines
Automatic equipment
Grinding machines
High speed transfer equipments
Injection moulding machines
Package Includes
1.5 meter Rail – 1
HG35 Bearing block – 1
Price 20,500 Birr
https://vector4engineering.com/product/rail-35mm/
Address – Megenagna, Zefmesh Grandmall 3rd floor 301
0993802995 Vector/0922787347 Kase
VECTOR FOUR ENGINEERING
PIC DEVELOPMENT BOARD
- Mini PIC System Development Board Microchip PIC16F877 PIC16F877A
- 4M crystal onboard, use socket, crystal frequency can be switched at any time.
- 4 independent keyboard, connected to RB0 RB1 RB2 RB3
- 8 LED connected to RD port, J3 plugged LED enabled, J3 unplugged RD port released completely.
- RS232 communication standard interface, microcontroller computer communication interface
- USB interface power supply (you can use another power supply)
- External 5V DC power interface
- power switch.Reset button
- ICSP simulation programming interface (K150 PICKIT2 PICKIT3 ICD2 etc.)
- VCC GND 8-pin power expansion interface, can be used to access or bring 5V power supply.
- Temperature sensor ds18b20 interface
- LCD1602/12864 LCD interface
Price 7000 Birr
https://vector4engineering.com/product/pic-development-board/
0993802995 Vector/0922787347 Kase
- Mini PIC System Development Board Microchip PIC16F877 PIC16F877A
- 4M crystal onboard, use socket, crystal frequency can be switched at any time.
- 4 independent keyboard, connected to RB0 RB1 RB2 RB3
- 8 LED connected to RD port, J3 plugged LED enabled, J3 unplugged RD port released completely.
- RS232 communication standard interface, microcontroller computer communication interface
- USB interface power supply (you can use another power supply)
- External 5V DC power interface
- power switch.Reset button
- ICSP simulation programming interface (K150 PICKIT2 PICKIT3 ICD2 etc.)
- VCC GND 8-pin power expansion interface, can be used to access or bring 5V power supply.
- Temperature sensor ds18b20 interface
- LCD1602/12864 LCD interface
Price 7000 Birr
https://vector4engineering.com/product/pic-development-board/
0993802995 Vector/0922787347 Kase