project title: IR based dish position control
ABSTRACT
Satellite dishes and antennas are mounted in very precarious locations, in an attempt to steer clear from any obstructions such as buildings and trees. This imposes risk when it comes to installing and servicing those installed dishes for proper alignment.
We therefore propose to design and implement a dish control system to assist in positioning and general installation of satellite dishes. This system will seek to use IR remote and receiver, Arduino and two Stepper motor to adjust the dish position.It consists of two motors that will enable the dish to move both in horizontal and vertical direction. An Arduino will be used as the controller to interface between the signals from the IR remote, to adjusting the motors. In the end, this project seeks to solve the problem of manually adjusting the dish and providing a safe solution for mounting satellite dishes.
Share share shaređđ
@thesisprojects
@niko12
đđđđđ
protues file and arduino code
ABSTRACT
Satellite dishes and antennas are mounted in very precarious locations, in an attempt to steer clear from any obstructions such as buildings and trees. This imposes risk when it comes to installing and servicing those installed dishes for proper alignment.
We therefore propose to design and implement a dish control system to assist in positioning and general installation of satellite dishes. This system will seek to use IR remote and receiver, Arduino and two Stepper motor to adjust the dish position.It consists of two motors that will enable the dish to move both in horizontal and vertical direction. An Arduino will be used as the controller to interface between the signals from the IR remote, to adjusting the motors. In the end, this project seeks to solve the problem of manually adjusting the dish and providing a safe solution for mounting satellite dishes.
Share share shaređđ
@thesisprojects
@niko12
đđđđđ
protues file and arduino code
đ1
dish_position_control.ino
2.6 KB
arduino code for implimentetion
dish_position_control_simulation.ino
2.5 KB
arduino code for simulation (use virtual terminal to send command)
áááá á¨áĽáľááá áĽáááľ á°á¨áłáŽá˝ á áá áĽááłá á1442áá á¨ááľ á áááĽá á áá á á°áá á á°á¨áłá˝á!
á áá á¨á°áá á¨áá á á¨á°áľáł ááá áááľ áááŤá áááłá˝áá áĽááááťáá!
#ááľ_ááŁá¨á
âŞâŞâŞâŞâŞâŞâŞâŞ
á áá á¨á°áá á¨áá á á¨á°áľáł ááá áááľ áááŤá áááłá˝áá áĽááááťáá!
#ááľ_ááŁá¨á
âŞâŞâŞâŞâŞâŞâŞâŞ
Project title: PID based dish position control with manual and auto mode.
(Auto correct wind disturbance)
Share share shaređđ
@thesisprojects
@niko12
đđđđđđ
Protues file..
(Auto correct wind disturbance)
Share share shaređđ
@thesisprojects
@niko12
đđđđđđ
Protues file..
Project title : Under and over voltage protection with status monitoring
Share share shaređđ
@thesisprojects
@niko12
đđđđđđ
Protues file..
Share share shaređđ
@thesisprojects
@niko12
đđđđđđ
Protues file..
Project title: solar based water pump and status monitoring
Share share shaređđ
@thesisprojects
@niko12
đđđđđđđ
Protues file..
Share share shaređđ
@thesisprojects
@niko12
đđđđđđđ
Protues file..
đ1
Project title: power factor compensator
(For inductive and capacitive load)
Share share shaređđ
@thesisprojects
@niko12
đđđđđđ
Protues file..
(For inductive and capacitive load)
Share share shaređđ
@thesisprojects
@niko12
đđđđđđ
Protues file..
Project title: vending machine
Share share shaređđ
@thesisprojects
@niko12
đđđđđđ
Protues file..
Share share shaređđ
@thesisprojects
@niko12
đđđđđđ
Protues file..
Project title: Web based patient monitoring system fully developed using yii2 php back-end frame work..
Share share shaređđ
@thesisprojects
@niko12
đđđđđđ
More detail..
Share share shaređđ
@thesisprojects
@niko12
đđđđđđ
More detail..