RX 6900 XT @ 8.87L
https://www.reddit.com/gallery/m71ufv

https://redd.it/m71ufv
@sffpc

Fan Configurations for NH-U12A in a S620?

Heya. Recently built a 5800X/2080 Super into a Sliger S620 with an NH-U12A and was curious to see what other folks have been doing fan config wise. I tried rear exhaust with top intake and had okay temps (40C idle/72C on load). Switched to rear intake and top exhaust and idle temps were higher (43C / 74C load). I was thinking of adding a side exhaust, but that'd mean I can't use the windowed panel.

I suppose I could use the alternate setup for the PSU so I can fit a front fan, but then I couldn't use the cables. (they juuuust fit in this config.)

Anyways, I know the more popular cooler to use is the NH-D15S but wanted to keep things a bit less crowded aesthetically.


https://preview.redd.it/rf7pfupegln61.jpg?width=1711&format=pjpg&auto=webp&s=1a58a81801bbbd9a34e6ec4fae62e5d185306f01

https://redd.it/m713qh
@sffpc

NCASE M1 Build and fan configuration testing

Hi,

not the best time to upgrade your system, but I couldn't resist.I already made a preview post about my ASUS Strix 3090 deshroud, but I wanted to show a bit more of my now finished build. I also uploaded a video of the deshrouding process, just a mostly raw uncut version though.

Specs:

|Mainboard|ASUS ROG CROSSHAIR VIII IMPACT|
|:-|:-|
|CPU|AMD Ryzen 9 5900X|
|GPU|ASUS GeForce RTX 3090 ROG STRIX OC WHITE|
|RAM|2x 16GB G.Skill Trident Z Neo 3800MHz, 14-16-16-36, (F4-3800C14D-32GTZN)|
|Power supply|Corsair SF750 Platinum 750W|
|CPU AiO|Alphacool Eisbaer LT 240|
|AiO Radiator Fan|2x Noctua A12x25|
|GPU Fan|2x Noctua A12x25|
|Storage|1x Samsung 960 EVO 1TB, 1x Samsung 970 EVO Plus 500GB|
|Case|NCASE M1 v6.1|

​

Inside

Top

Backside

Bottom, Fans slightly off center to better match the heat sink of the GPU

Side

Yes, the STRIX 3090 does not fit the NCASE M1. At least not without the use of a rotary tool.

But then it fits, no slim pci-e power connectors are necessary with a little cable managing.

even the front connectors are in place

​

I tested thermals with Fire Strike Ultra Graphics test 1 in a loop for at least 30 minutes with a period of roughly 5 minutes cool down afterwards. Logging was done with HWiNFO64. I set pump and CPU Radiator fans to a fixed RPM while changing the GPU fans in different fan configurations to match an 40db(A) noise level for comparison. Sadly the STRIX does not report RPM for the external fans, so for those only the % were logged.

Fire Strike Ultra settings for testing

Noise normalization to about 40db\(A\) from roughly 20cm

I tried the following configurations:

GPU 2x Noctua A12x25 Intake + CPU 2x Noctua A12x25 Intake
GPU 2x Noctua A12x25 Intake + CPU 2x Noctua A12x25 Exhaust
GPU 2x Noctua A12x25 Exhaust + CPU 2x Noctua A12x25 Exhaust
GPU 2x Noctua A14x25 Exhaust+ CPU 2x Noctua A12x25 Exhaust

I for some reason forgot to test GPU Exhaust and CPU Intake in this run, though I have tested it before and it didn't performe better than a full exhaust configuration.

As the GPU 2x Noctua A12x25 Exhaust + CPU 2x Noctua A12x25 Exhaust performed the best and furthermore the GPU 2x Noctua A12x25 Intake + CPU 2x Noctua A12x25 Exhaust crashed my system when I just closed Fire Strike due to an overheating of the motherboard and CPU, I didn't tested other configurations for the GPU 2x Noctua A14x25 than as Exhaust with the CPU also as Exhaust.

The Noctua A14x25 do not fit without grinding the fan's frame down on the inside where the ncase's mounting hardware for the side panel sits or removing said mounting brackets.

My custom profiles are fan curves for both CPU and GPU as well as an undervolt to

868mV at 1905Mhz Core Clock, +550Mhz RAM for the GPU.

Results, dT above ambient logged with a EVE Room

Thank you for reading, hope it helps, I'll try to answer any questions left unvoiced, but I won't take it apart for testing other configurations anymore, that whole process was a pain, thanks for your understanding!

https://redd.it/m734nc
@sffpc

NR200P + Fuma2 + MSI B550I + MSI RTX3080 Gaming X Trio
https://www.reddit.com/gallery/m74n7z

https://redd.it/m74n7z
@sffpc

K39 vs T40 from metalfish
https://redd.it/m77qlr
@sffpc

Are there any slim 140mm case fans with 140mm mounting holes?

Preferably 15mm or below. I did find the Thermaltake Luna 14 Slim LED, but it seems to be discontinued for years

https://redd.it/m74tb9
@sffpc

I’ve been playing a lot of Minecraft, and Valheim.

Thermals are pretty rad. Can’t complain for a first time pc build.

GPU: 30 - 56c
CPU: 50 - 78c

Built it before moving away for school in January. Here’s the parts list if anyone’s interested.

GPU: RTX 3090 FE
CPU: AMD 5800x
Case: Lian Ali TU-150 mini itx
CPU Cooler: Noctua NH-U12A
Mobo: Asus B550-I
Storage: Samsung 980 1TB M.2
Storage*: Seagate BarraCuda 1TB SSD
Memory: Crucial ballistics 32GB, 3200-DDR4
Power: Corsair SF 750w + plat

Case fans: 1xNoctua A12x25,
2xNoctua A12x15

[my pc pics](https://imgur.com/a/CnPgNoE/)

https://redd.it/m7aelp
@sffpc

My first approach to sffpc from mffpc 😇
https://redd.it/m7bwr0
@sffpc

NR200P Custom Loop White Build Complete
https://www.reddit.com/gallery/m7c07g

https://redd.it/m7c07g
@sffpc

Cooler Master NR200 3x240 radiators Water Cooling build.

First SFF build, came to NR200 from bq Dark Base 700.
What do You think guys?

Specs:
Motherboard: Asus X570 Crosshair VIII Impact [AM4\]
CPU: AMD Ryzen 9 5900X @ Curve Optimizer -30 [EK-Supremacy EVO RGB\]
RAM: 2x16GB 3200MHz CL14 G.Skill Trident Z RGB @ 3800 MHz CL16-16-16-32-48-319-1T, 1.39V
GPU: RTX 2080 Ti Founders Edition [EK WaterBlock\]
SSD1: Samsung 970 Evo Plus 1TB (Windows 10)
SSD2: 2x Crucial MX500 1TB [RAID 0\]
PSU: Cooler Master V850 SFX Gold [850 W\]
Case: Cooler Master MasterBox NR200 Black
Radiators : 2x XSPC 240x20mm, 1x Magicool G2 240x27mm
Fans: 4x Noctua NF-A12x15, 2x bq Silent Wings 3 120mm High-Speed
Pump: Laing DDC 3.25 DC - 1000 L/h
Tubing: EK ZMT 12/16

Had to cut one fan to fit RAM tabs.

PC without side radiator.

Different angle.

Clearance between GPU and bottom radiator is 1,5 cm. Had to take off audio cover to fit radiator.

PC with side radiator.

Shot from above.

Closed side panel.

Pump and reservoir \(IceMan NR200\). Had to cut 2 holes in case to get IN and OUT into PC.

I know this wall is garbage.

https://redd.it/m7bvd9
@sffpc

Best small Antennas on Amazon?

Have tried 2 different sets and they’ve both been absolutely terrible. I’m about 2 rooms away from my router. Using my motherboard antenna is perfectly fine but I want something small and out of sight. Any recommendations? Don’t mind spending extra for really good ones.

https://redd.it/m7da5t
@sffpc

My Vertical NR200p (builds.gg)
https://www.reddit.com/gallery/m7fco3

https://redd.it/m7fco3
@sffpc

Which layout is most optimal for my custom mesh sandwich-style case? (the black rectangles are fans). And yes, I'm aware that air passed thru the radiator isn't fresh & cool.
https://redd.it/m7g3yy
@sffpc

DAN A4 Build + 3950X

So finally most of my pain is over!

​

I put together this build as my personal rig for traveling, I really want to fit an EVGA 3070 which should fit, but will be awaiting the normal GPU pricing to return.

​

Managed to somehow fit 5 case fans in this, 2 of which are 120mm.

​

I strongly suggest printing the DAN case spacer from thingiverse, on the CPU side, allows about an extra 15mm, I think this will also be needed for the GPU side for most 30xx cards.

​

Dan Case A4

B450I GAMING PLUS AC WiFi AM4 Mini ITX

AMD Ryzen 9 3950X (16Core/32 Threads)

Corsair VENGEANCE RGB PRO 64GB (2x32GB) DDR4 3000

Palit NVIDIA GeForce RTX 2060 6GB

Corsair MP400 1TB M.2 PCIe

Samsung 4TB 860 SSD

Corsair SF Series SF600 SFX 600W Gold

AsusTek 92MM AIO + Noctua Fan

​

Partial build photo.

​

​

https://preview.redd.it/gp8h9k1mxnn61.jpg?width=2048&format=pjpg&auto=webp&s=49bb6e3dd9bdce237a6dc0237b6f61f3b33e10c4

https://preview.redd.it/26b5mq1mxnn61.jpg?width=3024&format=pjpg&auto=webp&s=e0928caf1560ebec5e52c5b6ed9f5ca964bd1f53

I really wanted the extra USB A's on the front as it's super helpful.

​

Stuff to revist:

​

Custom power cables. (I feel this caused generally so much pain in my build, but I wasn't able to find a supplier easily in the UK)

Reprint spacer with a few extra mm to stop the slight gap.

extend power button cable.

replace higher quality rise.

​

Idle Temps:

​

​

https://preview.redd.it/jpqewuauxnn61.png?width=508&format=png&auto=webp&s=45938ec940d18697ec97419318abbdbfb98b00c6

Build Cost:

Stuff was generally from Amazon UK / Warehouse, OCuK and Scan.

​

​

https://preview.redd.it/laxwjr020on61.png?width=420&format=png&auto=webp&s=8b4f57d45a0257d6359769edd003ead0f2e3ce3e

https://redd.it/m7c7su
@sffpc

Custom loop in a jonsbo A4

So I just wanted some input on what you guys think about a single loop with a 240 mil radiator and a 5800x and 3080. Would that be to hot in a single loop with even a decent undervolt on the gpu?

https://redd.it/m7jb5m
@sffpc

TU150 rear M.2 cooling question
https://redd.it/m7i7vl
@sffpc

Black Ridge Compatibility w/ 120mm Fan Underneath

So I have an MSI B550i motherboard, and I am going to be moving from an SG13 to a Velka 7. I recently made the purchase of VLP RAM so I can put a 120mm fan under the heatsink because I want maximum airflow obviously, but will it work on my board? Has anyone tried it out? I definitely would have to take off the m.2 heatsink in the front, which is no problem, but I'm not sure if I would have to make any other changes.

Also, what boards do people know work with this configuration? In the case that I need to change motherboards, it would be good for me (and others) to know what does work.

On a different note, I would not mind changing this motherboard as I have had so many times where bluetooth capability just goes away, sometimes for a minute, other times for a day, which is obviously very annoying as I rely on bluetooth for my audio often.

https://redd.it/m7e0kg
@sffpc

Smallest case for the EVGA 3060 XC?

I just got an EVGA 3060 XC and I'm keen to use it as a portable PCVR system with my Oculus. What is the smallest and most portable case that can fit the EVGA 3060 XC?

https://redd.it/m7la8i
@sffpc

Help Buying Aklla a4v2 / Ghost S1 in UK

Hi could do with a little help finding a case like the Ghost S1 or Aklla a4v2 in the UK

I'm using a TU150 at the mo but would like to downsize a little more, so any other case ideas would be awesome just needs to fit an SFX PSU and a TUF 3080 ( WHEN i can get my hands on one)

i'm just finding it hard to find small ITX cases in the UK.

Also what would be a good low profile cooler for a 9700K ?

Thanks

https://redd.it/m7m1bv
@sffpc

First SFF build getting a dual rad setup (5900x/RTX 3070) any tips?
https://redd.it/m7my9s
@sffpc