ထရန္စေဖာ္မာရဲ႕ Percentage Impedance
The percentage impedance of a transformer is the volt drop on full load due to the winding resistance and leakage reactance expressed as a percentage of the rated voltage. လို႔ define လုပ္ထားပါတယ္။ ထရန္စေဖာ္မာရဲ႕ Impedance တန္ဘိုးဟာ System Fault Current ကို မ်ားစြာ ေျပာင္းလဲေစပါတယ္၊ Fault ျဖစ္ခ်ိန္မွာ ထရန္စေဖာ္မာကို ျဖတ္ျပီး Fault Current ဘယ္ေလာက္ အမ်ားဆံုး စီးသြားႏိုင္မလဲ တြက္၍ ရပါတယ္၊ ထရန္စေဖာ္မာရဲ႕ Impedance တန္ဘိုးငယ္ေလ Fault Current မ်ားေလ ျဖစ္ပါ တယ္။ ထရန္စေဖာ္မာရဲ႕ Impedance တန္ဘိုးငယ္ေလ Fault Current မ်ားေလ ျဖစ္လို႕ Fault Current နည္း ဖို႔ရာ Impedance တန္ဘိုးၾကီးမွ ေကာင္းမယ္ရယ္လုိ႔ ေတြးျပန္ရင္ မွန္ေပမယ့္၊ Impedance တန္ဘိုး ၾကီး ရင္ ပံုမွန္ ဓာတ္အားေပးထားခ်ိန္မွာ Internal Voltage Drop မ်ားေစတယ္။ ဒါေၾကာင့္ Impedance တန္ဘိုး အနည္းအမ်ားဟာ သံုးစြဲသူရဲ႕ ေရြးခ်ယ္ရာပါပဲ။
ထရန္စေဖာ္မာ Impedance ကို လက္ေတြ႕ ဘယ္လိုတိုင္းမလဲ
၁။ ထရန္စေဖာ္မာ Secondary Side မွာ Short Circuit လုပ္ပါ (Ammeter တလံုးထဲ့ တပ္ထားပါ)၊
၂။ Primary Side ကေန Voltage Injector နဲ႔ Voltage တေျဖးေျဖးတင္သြားရပါမယ္၊ Secondary Side မွာ တပ္ထားတဲ့ Ammeter မွာ ထရန္စေဖာ္မာရဲ႕ Rated Secondary Current ေရာက္တဲ့အထိ တင္ေပးရတဲ့ Voltage ကို ဖတ္ပါ၊ အဲဒီ တန္ဘိုးကို Impedance Voltage လို႔ေခၚပါတယ္။
၃။ Impedance Voltage ကို Rated Primary Voltage နဲ႔စား၊ ၁၀၀ နဲ႔ေျမွာက္လို႔ ရတဲ့အေျဖကို Percentage Impedance of Transformer လို႔ေခၚပါတယ္။
Z% = ( Impedance Voltage x 100 ) / Rated Primary Voltage
Idea အျဖစ္ IEC 60076-5 ထဲက Transformer Percentage Impedance ဇယားေလး ကူးထဲ့ ေပးထားပါတယ္။
IEC 60076-5:2000 Power transformers - Part 5: Ability to withstand short circuit recommends a minimum impedance for transformers.
Unlike other standards such as the IEEE or AS which recommends typical values, IEC recommends minimum values. As these are minimum values, it does not mean that as an electrical designer, you can select very high impedances for your transformers. For example, IEC recommend 4%Z minimum impedance for a 300 kVA transformer. It does not mean however that you could have a 6.5%Z. Yes, you can there will be nobody preventing you to do that but transformer %Z in directly proportional to the transformer cost, size, and weight.
The percentage impedance of a transformer is the volt drop on full load due to the winding resistance and leakage reactance expressed as a percentage of the rated voltage. လို႔ define လုပ္ထားပါတယ္။ ထရန္စေဖာ္မာရဲ႕ Impedance တန္ဘိုးဟာ System Fault Current ကို မ်ားစြာ ေျပာင္းလဲေစပါတယ္၊ Fault ျဖစ္ခ်ိန္မွာ ထရန္စေဖာ္မာကို ျဖတ္ျပီး Fault Current ဘယ္ေလာက္ အမ်ားဆံုး စီးသြားႏိုင္မလဲ တြက္၍ ရပါတယ္၊ ထရန္စေဖာ္မာရဲ႕ Impedance တန္ဘိုးငယ္ေလ Fault Current မ်ားေလ ျဖစ္ပါ တယ္။ ထရန္စေဖာ္မာရဲ႕ Impedance တန္ဘိုးငယ္ေလ Fault Current မ်ားေလ ျဖစ္လို႕ Fault Current နည္း ဖို႔ရာ Impedance တန္ဘိုးၾကီးမွ ေကာင္းမယ္ရယ္လုိ႔ ေတြးျပန္ရင္ မွန္ေပမယ့္၊ Impedance တန္ဘိုး ၾကီး ရင္ ပံုမွန္ ဓာတ္အားေပးထားခ်ိန္မွာ Internal Voltage Drop မ်ားေစတယ္။ ဒါေၾကာင့္ Impedance တန္ဘိုး အနည္းအမ်ားဟာ သံုးစြဲသူရဲ႕ ေရြးခ်ယ္ရာပါပဲ။
ထရန္စေဖာ္မာ Impedance ကို လက္ေတြ႕ ဘယ္လိုတိုင္းမလဲ
၁။ ထရန္စေဖာ္မာ Secondary Side မွာ Short Circuit လုပ္ပါ (Ammeter တလံုးထဲ့ တပ္ထားပါ)၊
၂။ Primary Side ကေန Voltage Injector နဲ႔ Voltage တေျဖးေျဖးတင္သြားရပါမယ္၊ Secondary Side မွာ တပ္ထားတဲ့ Ammeter မွာ ထရန္စေဖာ္မာရဲ႕ Rated Secondary Current ေရာက္တဲ့အထိ တင္ေပးရတဲ့ Voltage ကို ဖတ္ပါ၊ အဲဒီ တန္ဘိုးကို Impedance Voltage လို႔ေခၚပါတယ္။
၃။ Impedance Voltage ကို Rated Primary Voltage နဲ႔စား၊ ၁၀၀ နဲ႔ေျမွာက္လို႔ ရတဲ့အေျဖကို Percentage Impedance of Transformer လို႔ေခၚပါတယ္။
Z% = ( Impedance Voltage x 100 ) / Rated Primary Voltage
Idea အျဖစ္ IEC 60076-5 ထဲက Transformer Percentage Impedance ဇယားေလး ကူးထဲ့ ေပးထားပါတယ္။
IEC 60076-5:2000 Power transformers - Part 5: Ability to withstand short circuit recommends a minimum impedance for transformers.
Unlike other standards such as the IEEE or AS which recommends typical values, IEC recommends minimum values. As these are minimum values, it does not mean that as an electrical designer, you can select very high impedances for your transformers. For example, IEC recommend 4%Z minimum impedance for a 300 kVA transformer. It does not mean however that you could have a 6.5%Z. Yes, you can there will be nobody preventing you to do that but transformer %Z in directly proportional to the transformer cost, size, and weight.