The logical sum of two or more than two logical products is termed as
A) OR operation B) POS C) SOP D) NAND operation
A) OR operation B) POS C) SOP D) NAND operation
Anonymous Quiz
27%
A
26%
B
41%
C
6%
D
CMOS technology used in?
A) Microprocessor B) Inverter C) Digital logic D) Both option a and c
A) Microprocessor B) Inverter C) Digital logic D) Both option a and c
Anonymous Quiz
16%
A
16%
B
17%
C
51%
D
When the PIV rating of a diode is exceeded
A) The diode behaves like a thyristor. B) The diode behaves like a resistor. C) The diode is destroyed. D) The diode behaves like a tunnel diode
A) The diode behaves like a thyristor. B) The diode behaves like a resistor. C) The diode is destroyed. D) The diode behaves like a tunnel diode
Anonymous Quiz
21%
A
30%
B
38%
C
11%
D
The basic building blocks of the arithmetic logic unit in digital computers are known as
A) Adders B) Attenuator C) Demultiplexer D) Subtractors
A) Adders B) Attenuator C) Demultiplexer D) Subtractors
Anonymous Quiz
47%
A
20%
B
28%
C
5%
D
Why is a decoder used in digital electronics?
A) To convert non coded information into a binary coded form. B) To convert coded information into a non-coded form. C) It is used to divide address bus and data bus. D) None of these
A) To convert non coded information into a binary coded form. B) To convert coded information into a non-coded form. C) It is used to divide address bus and data bus. D) None of these
Anonymous Quiz
28%
A
49%
B
20%
C
3%
D
👍1🥰1
What is the radix of the octal number system?
A) 2 B) 10 C) 8 D) 16
A) 2 B) 10 C) 8 D) 16
Anonymous Quiz
4%
A
18%
B
75%
C
4%
D
The two-transistor model of the SCR is obtained by
A) Bisecting the SCRs top two and bottom two layers B) Bisecting the SCRs top two layers C) Bisecting the SCRs bottom two Layers D) Bisecting the SCRs diagonally
A) Bisecting the SCRs top two and bottom two layers B) Bisecting the SCRs top two layers C) Bisecting the SCRs bottom two Layers D) Bisecting the SCRs diagonally
Anonymous Quiz
30%
A
23%
B
31%
C
16%
D
What is the main function of the filter in a rectifier circuit?
A) Maximize AC input variations B) To suppress odd harmonics. C) Remove ripples from the rectified output. D) Minimize DC input and AC output variations.
A) Maximize AC input variations B) To suppress odd harmonics. C) Remove ripples from the rectified output. D) Minimize DC input and AC output variations.
Anonymous Quiz
16%
A
17%
B
55%
C
12%
D
What is the actual meaning of the parallel load of a shift register?
A) All flip-flops are set with data. B) It means a parallel shifting of data. C) All flip-flops are present with data. D) Each flip flop is loaded with data simultaneously
A) All flip-flops are set with data. B) It means a parallel shifting of data. C) All flip-flops are present with data. D) Each flip flop is loaded with data simultaneously
Anonymous Quiz
12%
A
29%
B
24%
C
35%
D
In a 100 kHz clock frequency, 16 bits can be serially entered into a shift register?
A) 150 micro-sec B) 160 micro-sec C) 170 micro-sec D) 180 micro-sec
A) 150 micro-sec B) 160 micro-sec C) 170 micro-sec D) 180 micro-sec
Anonymous Quiz
13%
A
49%
B
29%
C
9%
D
A series of equal space time pulses may be easily generated by which type of counter circuit?
A) Johnson shift B) Clock shift C) Binary shift D) Ring counter
A) Johnson shift B) Clock shift C) Binary shift D) Ring counter
Anonymous Quiz
25%
A
29%
B
24%
C
22%
D
At which frequency the digital data can be applied to a gate?
A) Run-time frequency B) Propagation Frequency C) Operating frequency D) AC frequency
A) Run-time frequency B) Propagation Frequency C) Operating frequency D) AC frequency
Anonymous Quiz
24%
A
26%
B
47%
C
3%
D
What are the three output conditions of 3- state buffer?
A) High Impedance, 0, float B) Negative, positive, 0 C) 1, Low Impedance, float D) High, Low, float
A) High Impedance, 0, float B) Negative, positive, 0 C) 1, Low Impedance, float D) High, Low, float
Anonymous Quiz
31%
A
21%
B
19%
C
29%
D
In an 8 -bit Johnson counter sequence, how many states orbit patterns are possible?
A) 240 B) 228 C) 232 D) 220
A) 240 B) 228 C) 232 D) 220
Anonymous Quiz
28%
A
38%
B
29%
C
4%
D
Carrier lifetime for holes and electrons in a semiconductor ranges from –
A) Milliseconds to hundreds of nanoseconds B) Microseconds to seconds C) Nanoseconds to hundreds of microseconds D) Nanoseconds to thousands of milliseconds
A) Milliseconds to hundreds of nanoseconds B) Microseconds to seconds C) Nanoseconds to hundreds of microseconds D) Nanoseconds to thousands of milliseconds
Anonymous Quiz
24%
A
24%
B
27%
C
25%
D
🔥1
Which metal among these is widely used as a recombination agent by semiconductor manufacturers to obtain desired carrier lifetime of charge carriers?
A) Silver B)Gold C) Iron D) Aluminum
A) Silver B)Gold C) Iron D) Aluminum
Anonymous Quiz
22%
A
37%
B
13%
C
28%
D
The Hall effect is used to determine the
A) Only the carrier concentration of semiconductors B) Current flowing across a semiconductor C) Type of semiconductor and carrier concentration D) None of the above
A) Only the carrier concentration of semiconductors B) Current flowing across a semiconductor C) Type of semiconductor and carrier concentration D) None of the above
Anonymous Quiz
20%
A
30%
B
46%
C
4%
D
The thickness of space charge region for a P-N junction diode is of the order of :-
A) 10-4 cm B) 10-2 cm C) 10 cm D) 100 cm
A) 10-4 cm B) 10-2 cm C) 10 cm D) 100 cm
Anonymous Quiz
33%
A
47%
B
11%
C
8%
D
The voltage out of an ideal voltage source is
A. Zero
B. Constant C. Load resistance dependent D. Internal resistance dependent
A. Zero
B. Constant C. Load resistance dependent D. Internal resistance dependent
Anonymous Quiz
36%
A
32%
B
20%
C
12%
D
Pick the odd one in the group
A. Conductor
B. Semiconductor C. Four valence electrons D. Crystal structure
A. Conductor
B. Semiconductor C. Four valence electrons D. Crystal structure
Anonymous Quiz
34%
A
13%
B
17%
C
37%
D