In ETAP, what is the primary purpose of the "Sequence-of-Operation" feature when analyzing relay conditions?
Anonymous Quiz
18%
A) To calculate the power flow in the system
76%
B)To simulate and verify the tripping sequence and timing of protective devices for a specific fault
1%
C) To design the physical layout of the relay panel
5%
D) To generate a bill of materials for relay installation
When setting up relay conditions in ETAP for overcurrent protection, which of the following is the most critical parameter to ensure proper coordination between upstream and downstream relays?
Anonymous Quiz
20%
A) Relay pickup current
36%
B) Time Dial Setting (TDS)
20%
C) Instantaneous trip setting
24%
D) Relay type and curve selection
In a short-circuit calculation for a power system, the per-unit impedance of a generator is 0.15 pu, and the base MVA is 50 MVA. What is the short-circuit MVA at the generator terminals?
Anonymous Quiz
54%
A) 333.33 MVA
7%
B) 50 MVA
30%
C) 7.5 MVA
9%
D) 75 MVA
👍6❤1
When designing an earthing system for a substation, which standard is most commonly referenced for safety and performance in North America?
Anonymous Quiz
50%
A) IEEE 80
33%
B) IEC 60364
6%
C) BS 7671
11%
D) AS/NZS 3000
A motor with a power rating of 75 kW operates at a power factor of 0.85 and an efficiency of 90%. What is the input current if the supply voltage is 400 V (line-to-line) in a three-phase system?
Anonymous Quiz
37%
A) 123.6 A
39%
B) 150.5 A
9%
C) 98.7 A
15%
D) 175.2 A
Follow us on Instagram
https://www.instagram.com/p/DIIITN_TkUA/?utm_source=ig_web_copy_link&igsh=MzRlODBiNWFlZA==
https://www.instagram.com/p/DIIITN_TkUA/?utm_source=ig_web_copy_link&igsh=MzRlODBiNWFlZA==
👍1
In a lightning protection system, the air termination network is designed based on which protection method?
Anonymous Quiz
31%
A) Rolling sphere method
13%
B) Faraday cage method
12%
C) Mesh method
43%
D) All of the aboveAnswer: D) All of the above
👍1
What is the maximum allowable voltage drop for a feeder circuit as per the National Electrical Code (NEC) under normal conditions?
Anonymous Quiz
20%
A) 2%
27%
B) 3%
48%
C) 5%
5%
D) 10%
👍8
👍2
Do you Know in Buildings
According to Indian Electricity Rule, on Sub - Circuit can accommodate maximum of 10 points.
But Total connected load should not exceed 800W
According to Indian Electricity Rule, on Sub - Circuit can accommodate maximum of 10 points.
But Total connected load should not exceed 800W
👍2
What is the significance of the Short Circuit Ratio (SCR) in substation design?
Anonymous Quiz
5%
a) It determines the transformer cooling method
47%
b) It indicates the stability of the grid at the point of connection
37%
c) It measures the insulation level of busbars
11%
d) It defines the grounding resistance
Electrical Design Engineering
What is the maximum allowable voltage drop for a feeder circuit as per the National Electrical Code (NEC) under normal conditions?
In NEC Article 215.2(A)(1), Informational Note No. 1 suggests that for feeders, the voltage drop should generally be limited to 3% under normal operating conditions. This is to ensure efficient operation of the electrical equipment. Additionally, when combined with branch circuits, the total voltage drop (feeder plus branch circuit) should not exceed 5% from the supply side to the point of utilization (see NEC 210.19(A), Informational Note No. 4 for branch circuits, which aligns with this concept).
❤2
A load draws 50 kVAR of reactive power and 100 kW of real power. What is the apparent power of the load?
Anonymous Quiz
26%
A) 150 kVA
52%
B) 111.8 kVA
13%
C) 75 kVA
9%
D) 100 kVA.
❤2
Vacancy for freshers - Electrical
Apply on below link
https://www.instagram.com/p/DIRS06Mzj1o/?igsh=ZXNsMWUxbTVlNTA=
Apply on below link
https://www.instagram.com/p/DIRS06Mzj1o/?igsh=ZXNsMWUxbTVlNTA=