🚨 CVE-2026-80712
In the Linux kernel, the following vulnerability has been resolved:

spi: spi-qpic-snand: write the feature value before executing SET_FEATURE

qcom_spi_send_cmdaddr() programs NAND_FLASH_CMD/NAND_EXEC_CMD and submits
the descriptors, which makes the controller execute the command
immediately. For SPINAND_SET_FEATURE the value to be written is only
placed into NAND_FLASH_FEATURES afterwards, by qcom_spi_io_op(), in a
second submission - so the chip is programmed with whatever that register
happened to hold from a previous operation, and the intended value is only
applied by the *next* SET_FEATURE.

Measured on a TP-Link Archer AX55 v1 (IPQ5018, ESMT F50L1G41LB): writing
0x40 to the configuration register (0xb0) leaves the chip at 0x00, and the
subsequent write of 0x00 leaves it at 0x40 - every write lands one
operation late.

This stayed unnoticed until v6.18 added SPI-NAND OTP support together
with OTP entries for ESMT chips. spinand_otp_rw() enables OTP mode,
reads, and disables it again, and mtd_otp_nvmem_add() does this during
MTD registration. With the off-by-one, the "disable" write actually
applies the previously requested value, so CFG_OTP_ENABLE ends up set:
the chip stays in OTP mode, every subsequent array read returns the OTP
area instead of the array (UBI reports an empty device) and all writes
fail with -EIO because the OTP area is write protected. On this board
that makes the whole flash unusable and the device unbootable.

Write the feature value into NAND_FLASH_FEATURES as part of the same
transaction, before NAND_EXEC_CMD. While at it, copy only the bytes the
operation actually carries - the previous code dereferenced a 4-byte
pointer on a one-byte buffer (spinand->scratchbuf).

With this patch the flash contents read back bit-identical to a
known-good dump of the same board taken under the vendor firmware
(md5-verified across partitions), and writes work.

🎖@cveNotify

🚨 CVE-2026-80713
In the Linux kernel, the following vulnerability has been resolved:

io_uring: preserve task restrictions across exec

Per-task restrictions apply to all rings created by a task. Once
installed, they should not be dropped across exec.

For a task that has used io_uring, the exec cancellation path calls
__io_uring_free(). This frees both the task context and the per-task
restriction, so a ring created after exec is unrestricted.

Split task context cleanup into io_uring_free_tctx(), and use it from
the exec cancellation path. Keep __io_uring_free() for final task
cleanup, where both the context and restriction are released.

🎖@cveNotify

🚨 CVE-2026-80714
In the Linux kernel, the following vulnerability has been resolved:

ipvs: do not propagate one-packet flag to synced conns

Synced connections can be created before their destination exists. When
the destination is later added, ip_vs_bind_dest() copies connection flags
from the destination into cp->flags.

IP_VS_CONN_F_ONE_PACKET connections are not synced. If a synced
connection inherits IP_VS_CONN_F_ONE_PACKET while it is already hashed,
expiry can treat it as a one-packet connection and skip unlinking the
existing conn_tab node, leaving stale hash nodes pointing at a freed
struct ip_vs_conn.

Drop IP_VS_CONN_F_ONE_PACKET from destination flags when binding synced
connections.

🎖@cveNotify

🚨 CVE-2026-80716
In the Linux kernel, the following vulnerability has been resolved:

ALSA: pcm: wake linked drain waiters on unlink

snd_pcm_drain() on a linked stream parks an on-stack wait entry on the
drained peer's runtime->sleep, and after schedule_timeout() removes it
only if that peer is still found in the caller's group. If group
membership changes during the wait and the sleep ends by signal or
timeout (so autoremove_wake_function() does not run), finish_wait() is
skipped and snd_pcm_drain() returns with the entry still queued on that
stream's sleep list; a later wake_up() then walks a freed stack frame.
This is reachable by unlinking either the drained or the draining stream.

Unlike the close path (snd_pcm_drop() -> snd_pcm_post_stop()),
snd_pcm_unlink() never wakes the sleep queues. Wake every group member
under the group lock before the membership change, so a linked drainer is
released and drops its entry while the streams are still grouped.

The window was opened when snd_pcm_link_rwsem stopped being held across
the wait and the removal became conditional on group membership (see
Fixes). The later switch to finish_wait() kept that conditional removal,
so the signal/timeout case remained.

🎖@cveNotify

🚨 CVE-2026-80717
In the Linux kernel, the following vulnerability has been resolved:

sctp: validate Adaptation Indication parameter length

The Adaptation Layer Indication parameter contains a fixed 32-bit
Adaptation Code Point after its parameter header. However,
sctp_verify_param() accepts a header-only parameter because the generic
parameter walker only requires the header to be present.

sctp_process_param() then reads adaptation_ind beyond the declared
parameter. When the malformed parameter is last in an INIT, the read
starts at the receive skb tail, and the value is copied into the state
cookie returned in the INIT ACK. This may disclose four receive-buffer
tail bytes.

Require the declared parameter length to match the fixed structure size
and abort the association through the existing invalid parameter length
path otherwise.

🎖@cveNotify

🚨 CVE-2026-80718
In the Linux kernel, the following vulnerability has been resolved:

mm/percpu-km: fix bitmap overflow and accounting in pcpu_create_chunk()

In pcpu_create_chunk(), nr_pages is the total contiguous backing
allocation, i.e., nr_units * pcpu_unit_pages, but pcpu_chunk_populated()
uses it to set chunk->populated, whose size is pcpu_unit_pages, bitmap.
Since bit N in chunk->populated means page offset N inside every unit is
backed. When nr_units > 1, the function writes beyond chunk->populated.
Fix it by using chunk->nr_pages.

It also fixes the global pcpu_nr_empty_pop_pages accounting, since
pcpu_balance_free() only iterates up to chunk->nr_pages.

Commit a63d4ac4ab609 ("percpu: make percpu-km set chunk->populated bitmap
properly") introduced the bitmap overflow issue. Later, commit
b539b87fed37f ("percpu: implmeent pcpu_nr_empty_pop_pages and
chunk->nr_populated") added pcpu_nr_empty_pop_pages and caused the
accounting issue.

🎖@cveNotify

🚨 CVE-2026-80720
In the Linux kernel, the following vulnerability has been resolved:

iomap: add a separate bio_set for iomap_split_ioend

iomap_split_ioend can split bios that already come from
iomap_ioend_bioset and thus deadlock when the bioset is exhausted.

Add a separate bio_set to avoid this deadlock.

Christian Brauner <brauner@kernel.org> says:
Mark iomap_ioend_split_bioset static as it is only used in ioend.c,
fixing the sparse warning reported by the kernel test robot.

🎖@cveNotify

🚨 CVE-2026-80721
In the Linux kernel, the following vulnerability has been resolved:

Bluetooth: ISO: ensure no dangling hcon references in iso_conn

After iso_conn_del(), ISO sockets should not dereference the hcon any
more. Currently, clearing iso_conn::hcon relies on iso_conn_del()
releasing the last reference to the iso_conn.

Simplify this by explicitly clearing conn->hcon in iso_conn_del(), to
avoid more complex reasoning on races about who holds the last
reference.

🎖@cveNotify

🚨 CVE-2026-80722
In the Linux kernel, the following vulnerability has been resolved:

wifi: mac80211: validate individual TWT params before driver setup

ieee80211_process_rx_twt_action() only partially validates a received
S1G TWT setup frame before queueing it.

An individual agreement can therefore reach ieee80211_s1g_rx_twt_setup()
with twt->length too short for the full struct ieee80211_twt_params.

The individual path passes twt to drv_add_twt_setup(). Both the tracepoint
and the driver callback consume the complete parameters block, not merely
req_type. Do not pass a short individual agreement to the driver.
Broadcast agreements remain unchanged because they are rejected locally
after accessing only req_type.

[edit commit message to not overclaim lack of validation nor
understate driver impact]

🎖@cveNotify

🚨 CVE-2026-80723
In the Linux kernel, the following vulnerability has been resolved:

of: reserved_mem: prevent OOB when too many dynamic regions are defined

On boot, fdt_scan_reserved_mem() saves each dynamically-placed
/reserved-memory subnode into a local array of size
MAX_RESERVED_REGIONS.

If the device tree defines more than MAX_RESERVED_REGIONS
dynamically-placed regions, fdt_scan_reserved_mem() writes past the
end of the local array.

Add a bounds check that logs an error and skips the excess regions,
restoring the original behavior.

🎖@cveNotify

🚨 CVE-2026-80724
In the Linux kernel, the following vulnerability has been resolved:

ptp: vmclock: prevent read-only mappings from becoming writable

vmclock_miscdev_mmap() rejects writable mappings of the shared vmclock
ABI page with -EROFS, but leaves VM_MAYWRITE set. Userspace can map the
page read-only and then upgrade it to writable with mprotect(), after
which the guest can corrupt the host-written timekeeping data (sequence
counter, UTC time, TSC offset) that the vmclock ABI defines as read-only.

Clear VM_MAYWRITE on the read-only path so the mapping cannot be
upgraded, as i915 does for its read-only objects and as fixed in drm/vc4
(CVE-2026-68445) and drm/panthor (CVE-2024-53071).

🎖@cveNotify

🚨 CVE-2026-80725
In the Linux kernel, the following vulnerability has been resolved:

net: gro: properly validate BIG TCP aggregation criteria

When GRO attempts to aggregate packets beyond GRO_LEGACY_MAX_SIZE (64KB),
BIG TCP should only be permitted for plain IPv4 TCP and plain IPv6 TCP
(with sufficient MAC header room to insert the temporary HBH jumbo header).

However, commit b1a78b9b9886 ("net: add support for ipv4 big tcp")
loosened the check in skb_gro_receive(), leading to several issues:

1. skb_gro_receive() checked skb_headroom(p) instead of the actual space
before the MAC header (p->mac_header). Because skb_headroom(p) includes
mac_len, crafted frames (e.g. injected via AF_PACKET) can pass the check
with p->mac_header < 8 bytes. When ipv6_gro_complete() inserts the
temporary HBH jumbo header, the memmove() starts before skb->head,
causing an out-of-bounds write and wrapping skb->mac_header.
2. It allowed non-IP protocols such as software VLAN (ETH_P_8021Q /
ETH_P_8021AD) to aggregate beyond 64KB because
p->protocol != ETH_P_IPV6 was true.
3. It checked p->encapsulation instead of NAPI_GRO_CB(skb)->encap_mark,
allowing encapsulated flows (e.g. SIT / IPv6-in-IPv4) to aggregate
beyond 64KB.

Fix skb_gro_receive() to strictly enforce:
- NAPI_GRO_CB(skb)->proto == IPPROTO_TCP
- Not encapsulated (!NAPI_GRO_CB(skb)->encap_mark && !p->encapsulation)
- Protocol must be either ETH_P_IP or ETH_P_IPV6
- If ETH_P_IPV6, p->mac_header must be at least
sizeof(struct hop_jumbo_hdr)

Returning -E2BIG from skb_gro_receive() ensures that packets which cannot
become BIG TCP are cleanly flushed at <= 64KB and delivered intact without
dropping.

This issue does not exist in mainline (7.0+) because the subsystem was
rewritten in commit 81be30c1f5f2 ("net/ipv6: Drop HBH for BIG TCP on RX
side"), making this fix relevant only for older stable branches like
6.18.y.

🎖@cveNotify

🚨 CVE-2026-82364
A security vulnerability has been detected in macrozheng mall up to 1.0.3. This impacts an unknown function of the file /order/submit of the component Order Submission. The manipulation leads to race condition. It is possible to initiate the attack remotely. The attack is considered to have high complexity. The exploitability is said to be difficult. The vendor deleted the GitHub issue for this vulnerability without and explanation.

🎖@cveNotify

🚨 CVE-2026-6827
justhtml before 1.17.0 contains multiple security issues in sanitization, serialization, and programmatic DOM handling. When custom policies preserve foreign namespaces (SVG/MathML), dangerous content such as HTML integration points (SVG <foreignObject>, MathML <annotation-xml encoding="text/html">) and mutation-XSS parser-differential payloads could survive sanitization and become active HTML after reparse; SVG filter="url(...)" and preserved <style> could leave resource-loading CSS (@import, background-image:url()). Programmatic script/style/Comment nodes could serialize into active markup. Additional hardening fixes address sanitize-pipeline cache mutation and DOM parent/child cycles that could cause infinite loops. Most issues affect advanced or custom configurations rather than the default JustHTML(..., sanitize=True) safe path.

🎖@cveNotify

🚨 CVE-2026-77088
justhtml versions 0.9.0 through 1.21.0 contain a cross-site scripting vulnerability in to_markdown() where inline code spans fail to account for blank lines as block boundaries. Attackers can inject blank lines into code or pre element text to break the inline span, causing sanitized HTML to be emitted unescaped and re-parsed as live Markdown by compliant renderers.

🎖@cveNotify

🚨 CVE-2026-78206
exceljs through 4.4.0 decompresses all entries from supplied xlsx archives into memory without limits on entry size, total size, or compression ratio. Attackers can upload highly compressed workbooks that expand to gigabytes in memory, exhausting available resources and causing denial of service.

🎖@cveNotify

🚨 CVE-2026-78207
exceljs through 4.4.0 contains a prototype pollution vulnerability in the deepMerge helper that fails to reject __proto__, constructor, or prototype keys when merging note objects. Attackers can assign parsed JSON with a malicious __proto__ property to cell notes, modifying Object.prototype and affecting all plain objects created in the process.

🎖@cveNotify

🚨 CVE-2026-78208
exceljs through 4.4.0 contains a path traversal vulnerability in the Workbook.addImage() function that fails to validate file paths. Attackers can supply arbitrary file paths to read any file accessible to the Node.js process and embed it in the generated workbook.

🎖@cveNotify

🚨 CVE-2026-78209
exceljs through 4.4.0 fails to neutralize leading equals, plus, minus, or at signs in cell values written to CSV output. Attackers who can influence exported cell values can inject formulas that execute when the CSV file is opened in a spreadsheet application, potentially exfiltrating data or performing other malicious actions.

🎖@cveNotify

🚨 CVE-2026-77915
rConfig Core 8.0.0 before 8.2.10 contains an authentication bypass vulnerability that allows unauthenticated attackers to self-register accounts with full Administrator privileges due to a duplicate bare Auth::routes() call in routes/web.php that re-enables the POST /register route after it was explicitly disabled. Attackers can register a new account that is immediately authenticated with Admin-level access because the registration controller does not assign a role and the users.role column defaults to Admin, enabling access to stored device credentials, user data, and API token issuance.

🎖@cveNotify

🚨 CVE-2026-72699
The Grav Login plugin (getgrav/grav-plugin-login) before 3.9.1 is vulnerable to email address enumeration. The register() method in classes/Login.php throws a distinct exception (EMAIL_NOT_AVAILABLE) when a submitted email address already belongs to an existing account, while allowing registration to proceed otherwise. Because the registration endpoint has no rate limiting, an attacker can enumerate which email addresses have accounts on the site, one guess per request.

🎖@cveNotify