🚨 CVE-2026-74640
In the Linux kernel, the following vulnerability has been resolved:

ALSA: FCP: fix OOB write in fcp_meter_ctl_get()

fcp_ioctl_set_meter_map() bounds the user-supplied Level Meter map size
by the driver's own limit of 255

if (map.map_size < 1 || map.map_size > 255 ||
map.meter_slots < 1 || map.meter_slots > 255)
return -EINVAL;

and passes it to fcp_add_new_ctl() as the control's channel count, where
it is stored as elem->channels.

Every control read writes into struct snd_ctl_elem_value, whose integer
array is declared long value[128], so the limit is 128, not 255.
fcp_meter_ctl_get() stores one 64-bit word per channel into that array
with no bound of its own:

for (i = 0; i < elem->channels; i++) {
int idx = private->meter_level_map[i];
int value = idx < 0 ? 0 : le32_to_cpu(resp[idx]);

ucontrol->value.integer.value[i] = value;
}

snd_ctl_elem_read_user() serves that object from
memdup_user(_control, sizeof(*control)), 1224 bytes on LP64 out of
kmalloc-2048. offsetof(struct snd_ctl_elem_value, value) is 72, so
element i is written at byte 72 + 8 * i and element 144 already lands
past the allocation. At map_size 255 the last store ends at byte 2112,
888 bytes past the object and 64 bytes into the adjacent slab object.
The stored words come from the device and meter_level_map[] selects
which word lands in which slot, so extent and contents are both
controlled.

The core does not catch this. snd_ctl_check_elem_info() is reached only
from __snd_ctl_elem_info(), which snd_ctl_elem_read() calls under
CONFIG_SND_CTL_DEBUG; without that option snd_ctl_skip_validation() is a
compile-time true. __snd_ctl_add_replace() validates kcontrol->count and
never inspects elem->channels.

Installing an oversized map needs CAP_SYS_RAWIO, but the control outlives
the hwdep descriptor that created it, so the out-of-bounds stores are
issued by any process able to read controls on /dev/snd/controlC0.

KASAN on 7.2.0-rc5 (arm64), triggered by an unprivileged control read:

BUG: KASAN: slab-out-of-bounds in fcp_meter_ctl_get
Write of size 8 at addr ffff000017af04c8 by task fcp_trigger/185
__asan_store8
fcp_meter_ctl_get
snd_ctl_elem_read
snd_ctl_ioctl
Allocated by task 185:
memdup_user
snd_ctl_ioctl
The buggy address is located 0 bytes to the right of
allocated 1224-byte region [ffff000017af0000, ffff000017af04c8)

Bound the map size by the ABI limit rather than by 255, and bound the
store loop at the sink so it cannot run past the value array whatever
elem->channels holds.

Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>

🎖@cveNotify

🚨 CVE-2026-74641
In the Linux kernel, the following vulnerability has been resolved:

ALSA: usx2y: bound the hwdep mmap fault offset

snd_us428ctls_vm_fault() turns the faulting page offset into a kernel
address with no bound of any kind:

offset = vmf->pgoff << PAGE_SHIFT;
vaddr = (char *)(...)->us428ctls_sharedmem + offset;
page = virt_to_page(vaddr);
get_page(page);
vmf->page = page;

return 0;

snd_us428ctls_mmap() checks only the length of the mapping, never the
offset, and us428ctls_sharedmem is a single page from
alloc_pages_exact(). For a character device file_mmap_size_max()
returns ULONG_MAX, so the mm layer imposes no ceiling either. Every page
offset above zero resolves to a struct page outside the object, and the
handler installs it into the caller's address space read-write; the vma
is not marked read-only.

The caller picks the page frame with a single mmap() argument and gets
read-write access to a page of kernel memory it does not own; an offset
that lands in an unpopulated vmemmap region oopses instead.

A process that can open the hwdep node of an attached US-X2Y reaches
this after loading the FPGA image through the same node; no capability
check is involved.

On 7.2.0-rc5 (arm64), mmap() with a large offset:

Unable to handle kernel paging request at virtual address fffffdffc45d5ac8
pc : snd_us428ctls_vm_fault+0x68/0x140 [snd_usb_usx2y]
Call trace:
snd_us428ctls_vm_fault+0x68/0x140 [snd_usb_usx2y]
__do_fault
__handle_mm_fault
handle_mm_fault
el0_da

Reject any offset outside the shared region. The pcm hwdep handler in
usx2yhwdeppcm.c computes its address the same way and needs the same
bound.

Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>

🎖@cveNotify

🚨 CVE-2026-74642
In the Linux kernel, the following vulnerability has been resolved:

ALSA: usb: Fix UAF at delayed release of MIDI2 EPs

The recent fix for UAF in ump_to_endpoint() caused another UAF because
it tries to dereference the UMP endpoint object, but this might be
executed at a delayed context where the endpoint has been already
released.

Add private_free to clear the associated data for avoiding the further
dereference for delayed releases.

🎖@cveNotify

🚨 CVE-2026-74643
In the Linux kernel, the following vulnerability has been resolved:

samples/damon/mtier: error out for zero quota goal target values

Patch series "mm/damon: avoid division by zero from damos_quota_score()".

DAMON_SAMPLE_MTIER and DAMON_LRU_SORT allow the user to trigger division
by zero in damos_quota_score(). Avoid it by adding parameters validation
checks.


This patch (of 2):

damos_quota_score() can trigger division by zero if the target_value is
zero. DAMON_SAMPLE_MTIER lets users set the target_value via
node0_mem_{used,free}_bp parameters. It doesn't guard zero value case,
though. As a result, users can trigger division by zero. Fix the issue
by returning an error when the user tries to start DAMON with zero
node0_mem_{used,free}_bp parameter values.

DAMON_SAMPLE_MTIER is just a sample module, but the consequence is quite
bad. Also the zero node0_mem_free_bp parameter might look like a
reasonable setup to some users. Hence, the issue might really happen in
the real world.

One reliable way to reproduce the issue is like below:

# cd /sys/module/damon_sample_mtier/parameters
# echo 4096 > node0_start_addr
# echo 8192 > node0_end_addr
# echo 8192 > node1_start_addr
# echo 81920 > node1_end_addr
# echo 0 > node0_mem_free_bp
# echo Y > enabled
# dmesg -w
[...]
[18792.235916] Oops: divide error: 0000 [#1] SMP NOPTI
[...]
[18792.242787] RIP: 0010:damos_quota_score+0x6f/0x480
[...]

This issue was discovered [1] by Sashiko.

🎖@cveNotify

🚨 CVE-2026-74644
In the Linux kernel, the following vulnerability has been resolved:

mm/damon/ops-common: putback folios on invalid migrate nid

damon_pa_migrate() and damos_va_migrate() isolate folios into a local list
and then call damon_migrate_pages(). When target_nid is invalid
(including the scheme default NUMA_NO_NODE / -1), damon_migrate_pages()
returns early without putting the folios back to the LRU.

Callers then discard the list head while those folios remain isolated with
an extra reference taken by folio_isolate_lru(). The pages stay off the
LRU for as long as the mapping exists (anon active+inactive counts drop
while RSS does not), and the leftover references can pin the pages after
the mapping is gone.

Put the folios back on the invalid-nid path so ignored migration requests
still return them to the LRU.

🎖@cveNotify

🚨 CVE-2026-74646
In the Linux kernel, the following vulnerability has been resolved:

misc: fastrpc: take fl->lock when moving mmaps on interrupted invoke

When an invoke is interrupted by a signal,
wait_for_completion_interruptible() returns -ERESTARTSYS and
fastrpc_internal_invoke() moves every buffer from fl->mmaps onto
cctx->invoke_interrupted_mmaps. This list_del()/list_add_tail() walk
runs without holding fl->lock, the lock that serialises fl->mmaps in
fastrpc_req_mmap() and fastrpc_req_munmap() everywhere else.

Take fl->lock around the move, matching every other fl->mmaps accessor.

🎖@cveNotify

🚨 CVE-2026-74647
In the Linux kernel, the following vulnerability has been resolved:

misc: fastrpc: Remove buffer from list prior to unmap operation

fastrpc_req_munmap_impl() is called to unmap any buffer. The buffer is
getting removed from the list after it is unmapped from DSP. This can
create potential race conditions if multiple threads invoke unmap
concurrently, where one thread may remove the entry from the list while
another thread's unmap operation is still ongoing.

Fix this by removing the buffer entry from the list before calling the
unmap operation. If the unmap fails, the entry is re-added to the list
so that userspace can retry the unmap, or alternatively, the buffer
will be cleaned up during device release when the DSP process is torn
down and all DSP-side mappings are freed along with remaining buffers
in the list.

🎖@cveNotify

🚨 CVE-2026-74648
In the Linux kernel, the following vulnerability has been resolved:

staging: rtl8723bs: validate monitor transmit frame lengths

rtw_cfg80211_monitor_if_xmit_entry() removes the radiotap header and
then reads the 802.11 frame control field without checking that a base
802.11 header remains.

The data path also pulls the calculated 802.11, QoS and SNAP header
span before confirming that the skb contains it. A truncated frame can
therefore cause out-of-bounds reads or leave insufficient data for the
Ethernet address writes.

Reject frames that do not contain the base 802.11 header and data
frames that do not contain their complete calculated header span.

🎖@cveNotify

🚨 CVE-2026-74649
In the Linux kernel, the following vulnerability has been resolved:

staging: rtl8723bs: fix missing shared-key auth challenge length check

The WEP shared-key authentication handler uses the challenge-text
element's attacker-controlled length without checking it against the
fixed 128-byte chg_txt buffer.

In OnAuthClient() the length from rtw_get_ie() - up to 255 - is used
to perform memcpy() into the 128-byte pmlmeinfo->chg_txt, so a
malicious AP sending a malformed WLAN_EID_CHALLENGE element can
overflow/underfill chg_txt by up to 127 bytes. It is reachable over the
air, before association, during shared-key authentication. In the case
of an overflow, the driver can write out of bounds. In the case of an
underfill, the driver can echo stale buffer memory.

The challenge text is defined to be exactly 128 octets, which is
already provided as the WLAN_AUTH_CHALLENGE_LEN define; require the
element to be exactly that length before use.

🎖@cveNotify

🚨 CVE-2026-74650
In the Linux kernel, the following vulnerability has been resolved:

staging: rtl8723bs: fix OOB read in WMM_param_handler()

WMM_param_handler() copies a fixed-size WMM parameter element out of a
received information element without checking that the element is long
enough, causing an out-of-bounds read for a short WMM IE.

The handler reads sizeof(struct WMM_para_element) (18) bytes at
pIE->data + 6, so it requires pIE->length to be at least 24
(WLAN_WMM_LEN), but it never validates the length. Two of its three
callers reach it after matching only the WMM OUI: OnAssocRsp() in
rtw_mlme_ext.c matches a 6-byte OUI, and join_cmd_hdl() matches a
4-byte OUI, before calling the handler. A vendor-specific IE carrying
the WMM OUI but a length between 6 and 23, placed in an association
response or in the IE blob handed to join_cmd_hdl(), passes the OUI
check and then makes the memcmp() and memcpy() at pIE->data + 6 read
past the end of the element. OnAssocRsp() parses a frame received from
the AP, so this is reachable from a remote peer.

The remaining caller in rtw_wlan_util.c already guards the handler with
"pIE->length == WLAN_WMM_LEN". Move the equivalent check into the
handler itself so every caller is covered; the sibling IE handlers in
the same parsing loop (HT_caps_handler(), HT_info_handler(),
ERP_IE_handler()) likewise bound their accesses by pIE->length.

🎖@cveNotify

🚨 CVE-2026-74651
In the Linux kernel, the following vulnerability has been resolved:

staging: rtl8723bs: fix OOB read in rtw_get_wpa_ie()

rtw_get_wpa_ie() reads bytes at fixed offsets into a vendor-specific
information element without checking that the element is long enough,
causing an out-of-bounds read for a short trailing IE.

The function locates a vendor-specific IE (EID 221) with rtw_get_ie()
and then compares a 4-byte OUI+type at pbuf + 2 and reads a 2-byte
version word at pbuf + 6. Those accesses require the IE body to be at
least 6 bytes, but rtw_get_ie() only guarantees that the element fits
within the buffer; it does not enforce a minimum body length. A
vendor-specific IE whose length byte is 0 to 5, placed at the end of
the buffer, therefore makes these reads run past the end of the IE and
past the end of the buffer itself.

The buffer holds information elements taken from received management
frames and from the IE blob passed to rtw_cfg80211_set_wpa_ie(), which
is kmemdup'd to its exact length, so the read can run off the end of
the allocation.

The sibling helpers rtw_get_sec_ie(), rtw_get_wapi_ie() and
rtw_get_wps_ie() in this file already reject too-short vendor-specific
IEs before their OUI memcmp(); rtw_get_wpa_ie() was never brought in
line with them, and needs a minimum of 6 rather than 4 bytes because
of the version word. Add the missing length check.

🎖@cveNotify

🚨 CVE-2026-74652
In the Linux kernel, the following vulnerability has been resolved:

serial: amba-pl011: cancel RS485 hrtimers after freeing IRQ

The RS485 trigger hrtimers are embedded in the devm-managed port and can
fire after it is freed. The IRQ handler can arm a timer, so free the IRQ
first and then cancel both timers.

Complete the RS485 stop without arming a timer, and cancel the timers
in remove() for the suspend-then-unbind path, where shutdown is not
called.

This issue was found by an in-house static analysis tool.

🎖@cveNotify

🚨 CVE-2026-74653
In the Linux kernel, the following vulnerability has been resolved:

serial: 8250_of: clear stuck empty-FIFO RX-timeout on LPC32xx

The NXP LPC32xx UART (PORT_LPC3220) can latch an RX character-timeout
interrupt while the RX FIFO is empty: IIR reports UART_IIR_RX_TIMEOUT
(0x0c) but LSR.DR is clear. A character timeout is only cleared by
reading RHR, but serial8250_rx_chars() reads RHR only when LSR.DR is
set, so nothing ever clears the condition. The interrupt is
level-triggered and re-fires immediately, so on a single-core ARM926
the resulting interrupt storm livelocks the CPU.

It is reproducible when userspace repeatedly opens the front-panel port
(ttyS1): serial8250_do_set_termios() re-enables interrupts on unlock and
the handler then spins forever with iir=0xcc lsr=0x60 ier=0x05, tripping
the soft-lockup detector in serial8250_handle_irq_locked().

LPC32xx has no dedicated 8250 glue driver, it's driven by the generic
8250_of. Add a hardware specific handle_irq for PORT_LPC3220, wired up
in of_platform_serial_setup() the same way fsl8250_handle_irq is
installed. The handler follows dw8250_handle_irq(): on an RX timeout
with an empty FIFO (LSR.DR and LSR.BI clear) it does one throwaway RHR
read to clear the condition, then calls serial8250_handle_irq_locked().
No real received data is ever discarded, and it is a no-op on healthy
UARTs which never report a timeout with DR clear.

This is the same class of bug already worked around in other 8250 drivers;
see commit 424d79183af0 ("serial: 8250_dw: Avoid "too much work" from bogus rx timeout interrupt")
which reports the identical iir=0xcc/lsr=0x60. See also
UART_RX_TIMEOUT_QUIRK in 8250_omap, and the note in 8250_bcm7271.

🎖@cveNotify

🚨 CVE-2026-74654
In the Linux kernel, the following vulnerability has been resolved:

serial: 8250_dma: Clear stale RX state on shutdown

serial8250_release_dma() terminates RX DMA and releases the channel, but
leaves rx_running set. If the port is closed while an RX transfer is
active, the stale state remains while rxchan is NULL until the channel is
requested again on the next open.

The DesignWare BUSY workaround added by commit a7b9ce39fbe4
("serial: 8250_dw: Ensure BUSY is deasserted") calls
serial8250_rx_dma_flush() from the LCR write path during startup. This
happens before serial8250_request_dma() obtains a new RX channel. On
reopen, the stale rx_running state therefore makes the flush path pass a
NULL channel to dmaengine_pause(), causing a kernel Oops.

Clear rx_running after terminating RX DMA, matching the TX cleanup. Also
make the flush helper return if the DMA object or RX channel is not
available so startup and teardown paths cannot pass a NULL channel to the
DMAengine API.

🎖@cveNotify

🚨 CVE-2026-74655
In the Linux kernel, the following vulnerability has been resolved:

serial: qcom-geni: fix TX DMA buffer flush

When transmit flushing a qcom-geni UART during an ongoing TX DMA, the
UART gets stuck infinitely repeating corrupted TX DMA frames.

The DMA-mode uart_ops does not provide a flush_buffer callback, so an
in-flight transfer can complete after serial core has reset the transmit
kfifo, underflowing its length and resubmitting page-sized transfers
indefinitely. Add one that stops the transfer and clears tx_remaining
and tx_queued.

The stop path was also broken: it unmapped the buffer while the serial
engine could still read it, and never reset the TX DMA state machine.
Cancel the main sequencer command first, then reset the state machine
and wait for it before unmapping. Drop the early return so a pending
mapping is also cleaned up when the main command is inactive.

The bug can be triggered from userspace with a large write immediately
followed by TCOFLUSH. A following tcdrain will hang forever. The bug was
reproduced and this fix was validated on Arduino Uno Q (QRB2210)
using /dev/ttyHS1.

🎖@cveNotify

🚨 CVE-2026-74656
In the Linux kernel, the following vulnerability has been resolved:

ipv4: fix use-after-free in fib_nhc_update_mtu()

fib_nhc_update_mtu() walks the nexthop exception table under RTNL, but
RTNL does not serialize this walk with PMTU exception updates. The walk
uses rcu_dereference_protected() with a constant true condition without
holding fnhe_lock.

The following interleaving can therefore occur:

CPU 0 CPU 1
fib_nhc_update_mtu() update_or_create_fnhe()
load fnhe spin_lock_bh(&fnhe_lock)
fnhe_remove_oldest()
unlink fnhe
kfree_rcu(fnhe, rcu)
<quiescent state>
access fnhe after grace period

KASAN reported:

BUG: KASAN: slab-use-after-free in fib_nhc_update_mtu+0x3df/0x410
Read of size 8 at addr ffff888107d49000 by task poc/90
Call Trace:
fib_nhc_update_mtu+0x3df/0x410
fib_sync_mtu+0x7a/0xd0
fib_netdev_event+0x229/0x3f0
netif_set_mtu_ext+0x33a/0x570
dev_set_mtu+0x88/0x120

The same walk updates fnhe_pmtu and fnhe_mtu_locked. These fields form a
pair and other writers serialize them with fnhe_lock. RCU alone prevents
reclamation, but would still allow concurrent writers to leave a mixed
pair.

Walk the table under RCU and acquire fnhe_lock only while updating each
exception. RCU keeps the current entry alive while the short critical
section serializes its paired PMTU fields. This avoids holding the global
lock while scanning all 2048 buckets for every nexthop.

🎖@cveNotify

🚨 CVE-2026-74657
In the Linux kernel, the following vulnerability has been resolved:

ipv4: Fix fib_nlmsg_size() for RTA_VIA nexthops

fib_nlmsg_size() still estimates nexthop space as if every gateway is
encoded as an IPv4 RTA_GATEWAY attribute. IPv4 routes can also carry an
IPv6 gateway, which fib_nexthop_info() dumps as RTA_VIA.

As a result, route notifications can allocate an skb that is too small.
fib_dump_info() then fails with -EMSGSIZE and rtmsg_fib() hits the
WARN_ON() that marks such failures as a fib_nlmsg_size() bug. With
panic_on_warn set, this becomes a kernel panic.

Mirror the actual nexthop dump layout in fib_nlmsg_size(): account for
IPv6 nexthop gateways dumped as RTA_VIA, for the no-header rtnexthop
layout used inside RTA_MULTIPATH, and for RTA_FLOW only when it is
actually present.

🎖@cveNotify

🚨 CVE-2026-74658
In the Linux kernel, the following vulnerability has been resolved:

futex: Prevent robust futex exit race some more

A robust futex unlock stores 0 over the whole futex value - wiping
FUTEX_WAITERS - and wakes a single waiter. That wakeup is a one-shot
notification: the protocol relies on its recipient to either acquire the
futex (and eventually unlock while aware of the remaining contention) or
re-arm FUTEX_WAITERS before sleeping again. If the woken waiter is killed
before it can do either, the kernel must jump in and wake the next task
down the line.

This is a known complication of the futex protocol with a previous
partial fix in commit ca16d5bee598 ("futex: Prevent robust futex exit
race"). Unfortunately, that fix is insufficient.

If a third task re-acquired the futex through the uncontended fast
path in the meantime, the notification is lost: robust exit processing
sees that it is owned by another task and does nothing, while the new
owner sees no FUTEX_WAITERS when it unlocks and wakes nobody.
The remaining waiters sleep forever behind a free futex:

A owns the futex, B and C sleep in FUTEX_WAIT
uval == A | FUTEX_WAITERS
A robust unlock: store 0, FUTEX_WAKE(1) wakes B
uval == 0
D fast path acquire: cmpxchg(0 -> D)
uval == D, no FUTEX_WAITERS
B killed before acting on the wakeup
B exit walk, pending op: owner D != B -> no action
D unlock: no FUTEX_WAITERS -> no wake
C sleeps forever

This is clearly a shortcoming in the implementation, which fails to keep
the FUTEX_WAITERS bit consistent.

Work around this by augmenting the robust list exit processing to also
perform the extra wakeup if the futex word is owned by another thread but
FUTEX_WAITERS is not set.

This does not fix the problem of a non-contended take over/release and free
sequence, which has been discussed for years and has been addressed by
commit 3ca9595d9fb6 ("futex: Add support for unlocking robust futexes") and
subsequent changes, but failed to take the problem described above into
account.

A more complete solution which is based on the in kernel unlock of
contended robust futexes has been discussed in the context of this change
and should show up in mainline sooner than later.

[ tglx: Amend change log slightly and fixup coding style ]

🎖@cveNotify

🚨 CVE-2026-74659
In the Linux kernel, the following vulnerability has been resolved:

net: bridge: mrp: fix uninitialised bytes on the wire

br_mrp_alloc_test_skb() builds MRP test frames on an skb from
dev_alloc_skb(), which does not clear the linear data area. On the MRA
ring-role branch the sub-option TLV header is appended with

sub_tlv = skb_put(skb, sizeof(*sub_tlv));
sub_tlv->type = BR_MRP_SUB_TLV_HEADER_TEST_AUTO_MGR;

so sub_tlv->length is never written, and the two trailing alignment bytes
are appended with a bare skb_put() that does not clear them either. The
neighbouring oui and sub_opt regions are explicitly zeroed, so three
uninitialised bytes are left in every MRA MRP_Test frame that goes out.

Put the sub-option TLV header and the alignment padding in a single
skb_put_zero(), which clears both. The AUTO_MGR sub-TLV carries no
payload, so the zeroed length field is already the value it should have.

🎖@cveNotify

🚨 CVE-2026-74660
In the Linux kernel, the following vulnerability has been resolved:

netfilter: ebt_nflog: pin the NFLOG backend

nf_log_unregister() runs after the per-net teardown so its final RCU
grace period also drains readers that obtained the logger from a per-net
binding. However, ebt_nflog passes an explicit ULOG log type to
nf_log_packet() without holding a reference on the selected logger module,
unlike the xt_NFLOG and nft_log frontends.

An ebtables nflog rule can therefore remain callable while nfnetlink_log
is unloaded. The resulting interleaving is:

CPU 0 CPU 1
nfnetlink_log_fini()
unregister_pernet_subsys()
kfree(nfnl_log_pernet(net))
ebt_nflog_tg()
nf_log_packet()
nfulnl_log_packet()
instance_lookup_get_rcu()

The global ULOG logger is still registered at this point, so CPU 1
dereferences the per-net state after CPU 0 has freed it. KASAN reported:

BUG: KASAN: slab-use-after-free in instance_lookup_get_rcu
Read of size 8 at addr ff110001052e6210 by task poc/92
Call Trace:
instance_lookup_get_rcu+0x1ce/0x1f0 [nfnetlink_log]
nfulnl_log_packet+0x248/0x2fb0 [nfnetlink_log]
nf_log_packet+0x204/0x300
ebt_nflog_tg+0x351/0x550
ebt_do_table+0xedf/0x22b0
Allocated by task 90:
__kmalloc_noprof+0x186/0x470
ops_init+0x6d/0x420
register_pernet_operations+0x2f6/0x670
register_pernet_subsys+0x23/0x40
Freed by task 93:
kfree+0x131/0x3c0
ops_undo_list+0x3e3/0x700
unregister_pernet_operations+0x232/0x490
unregister_pernet_subsys+0x1c/0x30
nfnetlink_log_fini+0x34/0x450 [nfnetlink_log]

Acquire the ULOG logger module reference when an ebt_nflog rule is
validated and release it when the rule is destroyed. Request the NFLOG
backend for legacy callers when needed, matching xt_NFLOG. This prevents
module teardown until all ebt_nflog rules have stopped using the logger.

🎖@cveNotify

🚨 CVE-2026-74661
In the Linux kernel, the following vulnerability has been resolved:

mac802154: fix netdev use-after-free in beacon worker

mac802154_beacon_worker() reads local->beacon_req under RCU and derives
the sub-interface from the request, but then drops the RCU read lock and
continues to use both sdata and the embedded wpan_dev.

mac802154_stop_beacons_locked() cancels only pending beacon work, clears
local->beacon_req and frees the request. A beacon worker that is already
running can therefore continue after interface teardown and dereference
the freed netdev private area.

The scan worker already pins the netdev before leaving RCU. Apply the
same lifetime rule to the beacon worker: take a netdev reference while
the request is still protected by RCU, and release it on all paths that
continue after the reference is acquired.

🎖@cveNotify