🚨 CVE-2026-74552
In the Linux kernel, the following vulnerability has been resolved:

hwmon: (lm90) Only report alarms if driver is ready

Userspace can read sysfs attributes before driver registration is complete,
immediately after devm_hwmon_device_register_with_info() has been called.
At that time, data->hwmon_dev is not yet initialized. This can trigger
a NULL pointer access since lm90_update_device() and with it
lm90_update_alarms_locked() will be called. This call schedules
report_work and lm90_report_alarms(), which passes the still-NULL
data->hwmon_dev to hwmon_notify_event() and triggers a NULL pointer
dereference.

Fix the problem by only scheduling the report and alert workers
data->hwmon_dev is set.

🎖@cveNotify

🚨 CVE-2026-74553
In the Linux kernel, the following vulnerability has been resolved:

hwmon: (nct6775-core) Fix number of temperature registers for NCT6116

Unlike NCT6106, NCT6116 only has three temperature registers, and with
it only three temperature source and temperature source configuration
registers. The register addresses match those of NCT6106 and can be
re-used.

The code used a separate array to list the temperature source registers
for NCT6116, but used the size of the NCT6106 register array to set
the number of registers. The NCT6106 register array provides six addresses,
while the temperature source register array for NCT6116 only provides three
addresses. This causes a KASAN report.

BUG: KASAN: global-out-of-bounds in nct6775_probe+0x936/0x46f0 [nct6775]
Read of size 2 at addr ffffffffc19561a6 by task modprobe/954
...
Call Trace:
dump_stack+0x7d/0xa7
print_address_description.constprop.0+0x1c/0x220
? __kasan_kmalloc.constprop.0+0xc9/0xd0
? __kmalloc_node_track_caller+0x194/0x5b0
? nct6775_probe+0x936/0x46f0 [nct6775]
? nct6775_probe+0x936/0x46f0 [nct6775]
...

Fix the problem by hard-coding the number of temperature and temperature
configuration registers to three for NCT6116. Drop the unnecessary
NCT6116_REG_TEMP_SOURCE array and re-use NCT6106_REG_TEMP_SOURCE.

🎖@cveNotify

🚨 CVE-2026-74555
In the Linux kernel, the following vulnerability has been resolved:

scsi: libsas: Fix HA resume deadlock and hisi_sas disk-wake race

Commit fbefe22811c3 ("scsi: libsas: Don't always drain event workqueue
for HA resume") introduced sas_resume_ha_no_sync() to avoid a deadlock:
the PHYE_RESUME_TIMEOUT handler, running on the HA event workqueue,
calls sas_deform_port() -> sas_destruct_devices(), which removes SCSI
devices and waits for the host to become runtime-active. But the host
cannot resume until sas_resume_ha() -> sas_drain_work() returns, and the
drain is blocked on that very handler.

However skipping the drain reintroduces a race: hisi_sas returns from
resume before all PHY UP work and libsas discovery work finish. The
controller may then autosuspend while disks are still waking up. The
disks issue IO to a suspended controller, the IO fails, and the disks
get disabled.

Fix the deadlock at its source by moving the PHYE_RESUME_TIMEOUT
notification to after sas_drain_work(). By then the host resume is about
to complete, so device removal through device_link no longer blocks on
the resume and the cycle is broken.

With the deadlock gone, restore sas_resume_ha() (the draining variant)
in hisi_sas and remove sas_resume_ha_no_sync().

The reorder is safe for the other libsas consumers (isci, pm8001,
aic94xx, mvsas). During suspend, sas_suspend_devices() calls
sas_notify_lldd_dev_gone() for each device, which sets dev->lldd_dev to
NULL. When scsi_unblock_requests re-enables I/O in resume, any I/O to a
timed-out phy's disk is immediately rejected by the LLDD before reaching
hardware: isci returns SAS_DEVICE_UNKNOWN (mapped to DID_BAD_TARGET),
and pm8001 returns SAS_PHY_DOWN (mapped to DID_NO_CONNECT). Both
complete directly via scsi_done() without entering SCSI EH. This is
identical in both the old and new ordering since lldd_dev_gone runs
during suspend, before resume. The reorder only affects when the
PHYE_RESUME_TIMEOUT handler runs (synchronized by sas_drain_work()
vs. asynchronous after resume returns), not whether I/O can reach the
device. aic94xx and mvsas do not register any PM ops and never reach
this code path.

🎖@cveNotify

🚨 CVE-2026-74556
In the Linux kernel, the following vulnerability has been resolved:

scsi: libiscsi_tcp: Bound SCSI Response data segment to the connection buffer

iscsi_tcp_hdr_dissect() receives the data segment of several PDU types
into the fixed-size conn->data buffer, which is allocated for
ISCSI_DEF_MAX_RECV_SEG_LEN (8192) bytes. For the LOGIN_RSP, TEXT_RSP,
REJECT and ASYNC_EVENT opcodes the dissect path already rejects a PDU
whose DataSegmentLength exceeds that buffer.

The SCSI Command Response (ISCSI_OP_SCSI_CMD_RSP) path also copies its
data segment (sense/response data) into conn->data via
iscsi_tcp_data_recv_prep(), but it does so without the same check. The
only upstream bound on in.datalen is conn->max_recv_dlength, the
initiator's advertised MaxRecvDataSegmentLength, which is commonly
negotiated well above 8192 (open-iscsi defaults to 262144). A target
that returns a SCSI Response with a DataSegmentLength between 8193 and
max_recv_dlength therefore overflows the 8192-byte conn->data buffer.

Once the same bound applies, ISCSI_OP_SCSI_CMD_RSP is handled exactly
like those responses: bound the data segment, receive it into conn->data
when present, and otherwise complete the PDU with no data. Fold the
opcode into that case group rather than duplicating the check.

🎖@cveNotify

🚨 CVE-2026-74557
In the Linux kernel, the following vulnerability has been resolved:

scsi: libiscsi: Fix stale-data leak into the SCSI sense buffer

iscsi_scsi_cmd_rsp() copies the sense data of a SCSI Response from the
target-supplied data segment. The segment carries a 2-byte sense length
followed by the sense bytes, so it must hold 2 + senselen bytes, but the
bounds check only requires datalen >= senselen:

senselen = get_unaligned_be16(data);
if (datalen < senselen)
goto invalid_datalen;
memcpy(sc->sense_buffer, data + 2,
min_t(uint16_t, senselen, SCSI_SENSE_BUFFERSIZE));

A target that returns a SCSI Response whose datalen equals senselen
(with senselen <= SCSI_SENSE_BUFFERSIZE) makes the memcpy() from data +
2 read up to two bytes past the received data. Those bytes are stale
conn->data contents and end up in the command's sense buffer, which is
returned to userspace.

Account for the 2-byte sense length prefix in the check.

🎖@cveNotify

🚨 CVE-2026-74563
In the Linux kernel, the following vulnerability has been resolved:

rds: tcp: hold the RCU lock across ipv6_chk_addr() in rds_tcp_laddr_check()

rds_tcp_laddr_check() looks up a scoped IPv6 interface with
dev_get_by_index_rcu(), drops the RCU read-side lock, and only then
passes the bare struct net_device * into ipv6_chk_addr().

dev_get_by_index_rcu() only keeps the device alive within the same RCU
read-side section. After rcu_read_unlock(), a concurrent RTM_DELLINK can
free the net_device; ipv6_chk_addr() then dereferences the stale pointer
in __ipv6_chk_addr_and_flags() (e.g. l3mdev_master_dev_rcu(dev)), reading
freed memory.

Keep the RCU read-side lock held across the ipv6_chk_addr() call instead
of dropping it right after the lookup, so the device cannot be freed
while it is in use.

BUG: KASAN: slab-use-after-free in __ipv6_chk_addr_and_flags (... net/ipv6/addrconf.c:1998)
Read of size 8 at addr ffff8880106ec000 by task exploit/153
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
__ipv6_chk_addr_and_flags (... net/ipv6/addrconf.c:1998)
ipv6_chk_addr (net/ipv6/addrconf.c:2031 net/ipv6/addrconf.c:1972)
rds_tcp_laddr_check (net/rds/tcp.c:370)
rds_bind (net/rds/bind.c:248)
__sys_bind (net/socket.c:1920)
__x64_sys_bind (net/socket.c:1956)
do_syscall_64 (arch/x86/entry/syscall_64.c:63)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)

🎖@cveNotify

🚨 CVE-2026-74564
In the Linux kernel, the following vulnerability has been resolved:

netfilter: xt_hashlimit: validate hashtable supports XT_HASHLIMIT_RATE_MATCH

The XT_HASHLIMIT_RATE_MATCH flag mode changes the semantics of the
dsthash_ent structure which represents an entry in the hashtable. There
is a union area which uses a different layout to express the rate match
mode.

Update .checkentry path to validate the XT_HASHLIMIT_RATE_MATCH mode
flag is requested by two or more different rules that refer to the same
hashtable. Otherwise, uninitialized access to the burst field in the
union is possible.

Reject the use of the XT_HASHLIMIT_RATE_MATCH mode flag if set on by
revision less than 3 too.

🎖@cveNotify

🚨 CVE-2026-74566
In the Linux kernel, the following vulnerability has been resolved:

keys: make keyring key-chunk byte order agree with keyring_diff_objects()

keyring_get_key_chunk() loads description bytes into the index chunk low
address first, while keyring_diff_objects() numbers the first differing
bit from the low end and folds the absolute byte index into the level
without removing the inline-prefix offset the level already carries.
The two disagree on byte order and bit position, so the array can be
told two keys first differ at a bit that does not differ in the chunk
the walker uses, letting crafted descriptions collide into one node.

Load the chunk in the order keyring_diff_objects() assumes and drop the
inline-prefix length when folding the byte index into the level. This
only changes the in-memory ordering used to place keys within a keyring;
add, search and read of non-colliding keys are unaffected.

🎖@cveNotify

🚨 CVE-2026-74567
In the Linux kernel, the following vulnerability has been resolved:

keys: fix out-of-bounds read in keyring_get_key_chunk()

For description-level chunks keyring_get_key_chunk() advances the read
pointer by level * sizeof(long) past the inline prefix but only
bounds-checks the prefix, so a long enough key description is read past
its kmemdup(desc, desc_len + 1) allocation. Compute the full byte
offset and bounds-check the description against it before reading.

The walk only reaches a description-level chunk when two keys collide
through the hash, x, type and domain_tag chunks, so this is reached from
an unprivileged add_key(2) with a crafted pair of same-type keys whose
index hashes collide; KASAN reports a slab-out-of-bounds read.

🎖@cveNotify

🚨 CVE-2026-74577
In the Linux kernel, the following vulnerability has been resolved:

net: mpls: initialize rtm_tos in mpls_getroute()

mpls_getroute() builds the RTM_NEWROUTE reply to an RTM_GETROUTE
request by filling a struct rtmsg allocated from an skb whose data
area is not zeroed (alloc_skb(NLMSG_GOODSIZE, ...)). It sets every
field of the header except rtm_tos:

r = nlmsg_data(nlh);
r->rtm_family = AF_MPLS;
r->rtm_dst_len = 20;
r->rtm_src_len = 0;
r->rtm_table = RT_TABLE_MAIN;
r->rtm_type = RTN_UNICAST;
r->rtm_scope = RT_SCOPE_UNIVERSE;
r->rtm_protocol = rt->rt_protocol;
r->rtm_flags = 0;

struct rtmsg has no padding, so the one uninitialised byte rtm_tos
(offset 3) is copied straight to user space on recvmsg(), leaking a
byte of uninitialised heap memory. This is in contrast to
mpls_dump_route(), which fills the very same header and does set
rtm_tos = 0.

Initialize rtm_tos to 0, matching mpls_dump_route().

Reproduced with KMSAN by adding an MPLS route and issuing a
non-RTM_F_FIB_MATCH RTM_GETROUTE for its label:

BUG: KMSAN: kernel-infoleak in _copy_to_iter+0x36c/0x33f0
_copy_to_iter+0x36c/0x33f0
__skb_datagram_iter+0x196/0x12c0
skb_copy_datagram_iter+0x5b/0x210
netlink_recvmsg+0x37b/0xef0
...
Uninit was created at:
__alloc_skb+0x8ca/0x10e0
mpls_getroute+0x1280/0x3a40
rtnetlink_rcv_msg+0x1138/0x15a0
...
Byte 19 of 64 is uninitialized

(byte 19 = nlmsghdr(16) + rtmsg offset 3 = rtm_tos)

🎖@cveNotify

🚨 CVE-2026-74579
In the Linux kernel, the following vulnerability has been resolved:

netfilter: nft_payload: fix mask build for partial field offload

nft_payload_offload_mask() builds the offload match mask for a payload
expression that covers only part of a header field. For a partial IPv6
address match (field_len = 16, priv_len = 1) that shift is 1 << 120, which
is undefined on the 32-bit int operand. It also trims only one word, so
the remaining words stay 0xffffffff (and when priv_len is a multiple of 4
the trim is skipped entirely), leaving the mask covering more bytes than
the rule matches.

UBSAN: shift-out-of-bounds in net/netfilter/nft_payload.c:278:20
shift exponent 120 is too large for 32-bit type 'int'
...

The match is byte-granular and struct nft_data is zero-initialised, so the
correct mask is simply the first priv_len bytes set to 0xff. Set those
bytes directly and drop the word/shift trimming; this removes the undefined
shift and no longer over-masks the trailing bytes.

🎖@cveNotify

🚨 CVE-2026-74969
Use-after-free in the Layout: Text and Fonts component. This vulnerability was fixed in Firefox 154, Firefox ESR 115.39, Firefox ESR 140.14, Firefox ESR 153.1, Thunderbird 154, Thunderbird 140.14, and Thunderbird 153.1.

🎖@cveNotify

🚨 CVE-2026-70657
Copyparty is a portable file server. Prior to 1.20.17, copyparty volumes with the dk or dks directory-key flag combined with the fk or fka file-key flag can convert a valid file key into a directory key, granting read access to the containing folder. This vulnerability was only reachable if both types of keys (filekeys and dirkeys) were manually enabled in the volume flags simultaneously. This issue is fixed in version 1.20.17.

🎖@cveNotify

🚨 CVE-2026-76038
Type confusion in V8 in Google Chrome prior to 151.0.7922.169 allowed a remote attacker to execute arbitrary code inside the sandbox via a crafted HTML page. (Chromium security severity: High)

🎖@cveNotify

🚨 CVE-2026-73974
linuxfabrik-lib provides Python modules for database access, caching, shell execution, and API integrations, and Linuxfabrik Monitoring Plugins uses its shared testing helper across check plugins. Prior to linuxfabrik-lib 6.1.0 and Linuxfabrik Monitoring Plugins 7.0.0, lib.lftest.test() treated the first or second element of a --test CSV argument as a filesystem path and returned the file contents as simulated standard output or standard error without path confinement. The hidden but production-accessible --test argument was accepted by sudo-authorized plugins, so an attacker controlling the nagios or icinga account could use check-plugins/deb-updates/deb-updates with its default QUERY=1 to disclose every line of a root-readable file. Approximately 22 other plugins exposed filtered content or a root file existence and readability oracle through the same helper, while check-plugins/network-bonding/network-bonding and check-plugins/openstack-swift-stat/openstack-swift-stat had direct read paths that bypassed the helper. The library fix confines fixture reads to the invoking plugin's unit-test directory and refuses unsafe anchors, and the plugin fix routes the two bypasses through that helper. These issues are fixed in linuxfabrik-lib 6.1.0 and Linuxfabrik Monitoring Plugins 7.0.0.

🎖@cveNotify

🚨 CVE-2026-71470
A flaw was found in the search-v2-operator. This vulnerability allows a privileged user, specifically a Custom Resource (CR) editor, to manipulate Search CR fields such as imageOverride, arguments, and environment variables without proper validation. By exploiting this, an attacker can mount arbitrary secrets into a search container's environment or replace the container image with an attacker-controlled one. This leads to privilege escalation and can result in a full cluster compromise due to the ServiceAccount's extensive impersonation permissions.

🎖@cveNotify

🚨 CVE-2026-72529
A remote unauthorized attacker with network access via port 4307/TCP to the TrueConf server versions 5.3.X to 5.3.9, 5.4.X to 5.4.9, 5.5.X to 5.5.5, and earlier could execute an arbitrary script by calling an undocumented function.

🎖@cveNotify

🚨 CVE-2026-72530
A remote unauthorized attacker with network access via port 4307/TCP to the TrueConf server versions 5.3.X to 5.3.9, 5.4.X to 5.4.9, 5.5.X to 5.5.5, and earlier could use a specially crafted script to break out of the isolated environment and execute arbitrary code on the host system.

🎖@cveNotify

🚨 CVE-2026-75141
FFmpeg before commit acf5d7c contains a heap buffer overflow in the hvcC box writer. When writing an HEVC configuration record with more NAL units of a single type than the count field can represent, the NAL unit count overflows, causing a heap buffer overflow. A crafted HEVC input file triggers the overflow during muxing.

🎖@cveNotify

🚨 CVE-2026-75142
FFmpeg before commit 9d786e4 contains a stack buffer overflow in the MPEG-PS muxer (libavformat/mpegenc.c). When muxing input with more streams than the muxer's fixed-size stack buffer accommodates, the buffer is overflowed. A crafted input with an excessive number of streams triggers the overflow during MPEG-PS muxing.

🎖@cveNotify

🚨 CVE-2026-75143
FFmpeg before commit 1c10bcc contains a heap buffer overflow in the RIST protocol reader (libavformat/librist.c). librist_read() ignored its size argument and copied the full received payload length into the caller-provided destination buffer, overflowing it when the payload exceeds the destination size. This is reachable via the async:rist:// URL scheme, where the async wrapper supplies a smaller buffer than the received payload. A remote RIST sender can trigger the overflow by sending a packet whose payload exceeds the caller buffer size.

🎖@cveNotify