🚨 CVE-2026-74559
In the Linux kernel, the following vulnerability has been resolved:
xsk: drain continuation descs after overflow in xsk_build_skb()
Fix generic xmit path multi-buffer logic when packets are either too big
(count of descriptors exceed MAX_SKB_FRAGS) or an invalid descriptor is
included in fragmented packet. Introduce xdp_sock::drain_cont and act
upon this flag - when it is set, keep on consuming descriptors from
AF_XDP Tx ring and put them directly onto Cq. Previously these
descriptors were silently lost and could never be reached again.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
xsk: drain continuation descs after overflow in xsk_build_skb()
Fix generic xmit path multi-buffer logic when packets are either too big
(count of descriptors exceed MAX_SKB_FRAGS) or an invalid descriptor is
included in fragmented packet. Introduce xdp_sock::drain_cont and act
upon this flag - when it is set, keep on consuming descriptors from
AF_XDP Tx ring and put them directly onto Cq. Previously these
descriptors were silently lost and could never be reached again.
🎖@cveNotify
🚨 CVE-2026-74560
In the Linux kernel, the following vulnerability has been resolved:
xsk: fix buffer leak in xsk_drop_skb() for AF_XDP multi-buffer Tx
This patch is inspired by the check[1] from sashiko. It says when
overflow happens, the address of cq to be published is invalid.
Actually the severer thing is the whole process of publishing the
address of cq in this particular case is not right: it should truely
publish the address and advance the cached_prod in cq as long as it
reads descriptors from txq.
The following is the full analysis.
xsk_drop_skb() is called in three places, which all discard a partially
built multi-buffer skb:
1) xsk_build_skb() -EOVERFLOW error path: packet exceeds MAX_SKB_FRAGS
2) __xsk_generic_xmit() post-loop cleanup: an invalid descriptor in
the TX ring prevents the partial packet from completing
3) xsk_release(): socket close while xs->skb holds an incomplete packet
In all three cases, the TX descriptors for the already-processed frags
have been consumed from the TX ring (xskq_cons_release), and CQ slots
have been reserved. However, xsk_drop_skb() calls xsk_consume_skb()
which cancels the CQ reservations via xsk_cq_cancel_locked(). Since
the buffer addresses never appear in the completion queue, userspace
permanently loses track of these buffers.
Fix this by letting consume_skb() trigger the existing xsk_destruct_skb
destructor, which already submits buffer addresses to the CQ via
xsk_cq_submit_addr_locked().
Note that cancelling the descriptors back to the TX ring (via
xskq_cons_cancel_n) is not a appropriate option because an oversized
packet that always exceeds MAX_SKB_FRAGS would be retried indefinitely,
which is an obviously deadlock bug in the TX path.
Also move the desc->addr assignment in xsk_build_skb() above the
overflow check so that the current descriptor's address is recorded
before a potential -EOVERFLOW jump to free_err, consistent with the
zerocopy path in xsk_build_skb_zerocopy().
[1]: https://lore.kernel.org/all/20260425041726.85FB3C2BCB2@smtp.kernel.org/
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
xsk: fix buffer leak in xsk_drop_skb() for AF_XDP multi-buffer Tx
This patch is inspired by the check[1] from sashiko. It says when
overflow happens, the address of cq to be published is invalid.
Actually the severer thing is the whole process of publishing the
address of cq in this particular case is not right: it should truely
publish the address and advance the cached_prod in cq as long as it
reads descriptors from txq.
The following is the full analysis.
xsk_drop_skb() is called in three places, which all discard a partially
built multi-buffer skb:
1) xsk_build_skb() -EOVERFLOW error path: packet exceeds MAX_SKB_FRAGS
2) __xsk_generic_xmit() post-loop cleanup: an invalid descriptor in
the TX ring prevents the partial packet from completing
3) xsk_release(): socket close while xs->skb holds an incomplete packet
In all three cases, the TX descriptors for the already-processed frags
have been consumed from the TX ring (xskq_cons_release), and CQ slots
have been reserved. However, xsk_drop_skb() calls xsk_consume_skb()
which cancels the CQ reservations via xsk_cq_cancel_locked(). Since
the buffer addresses never appear in the completion queue, userspace
permanently loses track of these buffers.
Fix this by letting consume_skb() trigger the existing xsk_destruct_skb
destructor, which already submits buffer addresses to the CQ via
xsk_cq_submit_addr_locked().
Note that cancelling the descriptors back to the TX ring (via
xskq_cons_cancel_n) is not a appropriate option because an oversized
packet that always exceeds MAX_SKB_FRAGS would be retried indefinitely,
which is an obviously deadlock bug in the TX path.
Also move the desc->addr assignment in xsk_build_skb() above the
overflow check so that the current descriptor's address is recorded
before a potential -EOVERFLOW jump to free_err, consistent with the
zerocopy path in xsk_build_skb_zerocopy().
[1]: https://lore.kernel.org/all/20260425041726.85FB3C2BCB2@smtp.kernel.org/
🎖@cveNotify
🚨 CVE-2026-74561
In the Linux kernel, the following vulnerability has been resolved:
nexthop: avoid unlocked f6i_list walk in nh_rt_cache_flush
nh_rt_cache_flush() walks nh->f6i_list during an RTNL-serialized nexthop
replace without holding nh->lock, racing the unlocked IPv6 route
add/delete that mutate the list under nh->lock and free fib6_info
entries (nh_rt_cache_flush() is inlined into rtm_new_nexthop()):
BUG: KASAN: slab-use-after-free in nh_rt_cache_flush (net/ipv4/nexthop.c:2243)
Read of size 8 at addr ffff888012953e18 by task exploit/146
nh_rt_cache_flush (net/ipv4/nexthop.c:2243)
replace_nexthop (net/ipv4/nexthop.c:2610)
rtm_new_nexthop (net/ipv4/nexthop.c:3323)
rtnetlink_rcv_msg (net/core/rtnetlink.c:7076)
Unlike the other f6i_list walks, this one bumps each route's sernum via
fib6_update_sernum_upto_root(), which needs tb6_lock; taking nh->lock
around it would invert the established tb6_lock -> nh->lock order and
deadlock. As the only purpose is to invalidate cached dsts, bump the
IPv6 sernum for the whole netns with rt_genid_bump_ipv6() instead,
mirroring the rt_cache_flush() already done for IPv4 just above.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
nexthop: avoid unlocked f6i_list walk in nh_rt_cache_flush
nh_rt_cache_flush() walks nh->f6i_list during an RTNL-serialized nexthop
replace without holding nh->lock, racing the unlocked IPv6 route
add/delete that mutate the list under nh->lock and free fib6_info
entries (nh_rt_cache_flush() is inlined into rtm_new_nexthop()):
BUG: KASAN: slab-use-after-free in nh_rt_cache_flush (net/ipv4/nexthop.c:2243)
Read of size 8 at addr ffff888012953e18 by task exploit/146
nh_rt_cache_flush (net/ipv4/nexthop.c:2243)
replace_nexthop (net/ipv4/nexthop.c:2610)
rtm_new_nexthop (net/ipv4/nexthop.c:3323)
rtnetlink_rcv_msg (net/core/rtnetlink.c:7076)
Unlike the other f6i_list walks, this one bumps each route's sernum via
fib6_update_sernum_upto_root(), which needs tb6_lock; taking nh->lock
around it would invert the established tb6_lock -> nh->lock order and
deadlock. As the only purpose is to invalidate cached dsts, bump the
IPv6 sernum for the whole netns with rt_genid_bump_ipv6() instead,
mirroring the rt_cache_flush() already done for IPv4 just above.
🎖@cveNotify
🚨 CVE-2026-74562
In the Linux kernel, the following vulnerability has been resolved:
nexthop: take nh->lock for f6i_list walks in replace check and notify
fib6_check_nh_list() and __nexthop_replace_notify() walk nh->f6i_list
during an RTNL-serialized nexthop replace without holding nh->lock. IPv6
RTM_NEWROUTE/RTM_DELROUTE run without RTNL and mutate that list under
nh->lock (fib6_add_rt2node_nh(), fib6_purge_rt()), so both walks race a
concurrent route delete that unlinks and frees a fib6_info:
BUG: KASAN: slab-use-after-free in rt6_fill_node.isra.0 (net/ipv6/route.c:5799)
Read of size 4 at addr ffff888014607e64 by task exploit/143
rt6_fill_node.isra.0 (net/ipv6/route.c:5799)
fib6_rt_update (net/ipv6/route.c:6412)
__nexthop_replace_notify (net/ipv4/nexthop.c:2542)
rtm_new_nexthop (net/ipv4/nexthop.c:2554)
rtnetlink_rcv_msg (net/core/rtnetlink.c:7076)
BUG: KASAN: slab-use-after-free in fib6_check_nh_list (net/ipv4/nexthop.c:1605)
Read of size 8 at addr ffff888014a7d068 by task exploit/142
fib6_check_nh_list (net/ipv4/nexthop.c:1605)
rtm_new_nexthop (net/ipv4/nexthop.c:2575)
rtnetlink_rcv_msg (net/core/rtnetlink.c:7076)
Both walks only read the entries and take no tb6_lock, so protect them
with nh->lock; fib6_rt_update() uses gfp_any(), which returns GFP_ATOMIC
under the lock.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
nexthop: take nh->lock for f6i_list walks in replace check and notify
fib6_check_nh_list() and __nexthop_replace_notify() walk nh->f6i_list
during an RTNL-serialized nexthop replace without holding nh->lock. IPv6
RTM_NEWROUTE/RTM_DELROUTE run without RTNL and mutate that list under
nh->lock (fib6_add_rt2node_nh(), fib6_purge_rt()), so both walks race a
concurrent route delete that unlinks and frees a fib6_info:
BUG: KASAN: slab-use-after-free in rt6_fill_node.isra.0 (net/ipv6/route.c:5799)
Read of size 4 at addr ffff888014607e64 by task exploit/143
rt6_fill_node.isra.0 (net/ipv6/route.c:5799)
fib6_rt_update (net/ipv6/route.c:6412)
__nexthop_replace_notify (net/ipv4/nexthop.c:2542)
rtm_new_nexthop (net/ipv4/nexthop.c:2554)
rtnetlink_rcv_msg (net/core/rtnetlink.c:7076)
BUG: KASAN: slab-use-after-free in fib6_check_nh_list (net/ipv4/nexthop.c:1605)
Read of size 8 at addr ffff888014a7d068 by task exploit/142
fib6_check_nh_list (net/ipv4/nexthop.c:1605)
rtm_new_nexthop (net/ipv4/nexthop.c:2575)
rtnetlink_rcv_msg (net/core/rtnetlink.c:7076)
Both walks only read the entries and take no tb6_lock, so protect them
with nh->lock; fib6_rt_update() uses gfp_any(), which returns GFP_ATOMIC
under the lock.
🎖@cveNotify
🚨 CVE-2026-74563
In the Linux kernel, the following vulnerability has been resolved:
rds: tcp: hold the RCU lock across ipv6_chk_addr() in rds_tcp_laddr_check()
rds_tcp_laddr_check() looks up a scoped IPv6 interface with
dev_get_by_index_rcu(), drops the RCU read-side lock, and only then
passes the bare struct net_device * into ipv6_chk_addr().
dev_get_by_index_rcu() only keeps the device alive within the same RCU
read-side section. After rcu_read_unlock(), a concurrent RTM_DELLINK can
free the net_device; ipv6_chk_addr() then dereferences the stale pointer
in __ipv6_chk_addr_and_flags() (e.g. l3mdev_master_dev_rcu(dev)), reading
freed memory.
Keep the RCU read-side lock held across the ipv6_chk_addr() call instead
of dropping it right after the lookup, so the device cannot be freed
while it is in use.
BUG: KASAN: slab-use-after-free in __ipv6_chk_addr_and_flags (... net/ipv6/addrconf.c:1998)
Read of size 8 at addr ffff8880106ec000 by task exploit/153
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
__ipv6_chk_addr_and_flags (... net/ipv6/addrconf.c:1998)
ipv6_chk_addr (net/ipv6/addrconf.c:2031 net/ipv6/addrconf.c:1972)
rds_tcp_laddr_check (net/rds/tcp.c:370)
rds_bind (net/rds/bind.c:248)
__sys_bind (net/socket.c:1920)
__x64_sys_bind (net/socket.c:1956)
do_syscall_64 (arch/x86/entry/syscall_64.c:63)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
rds: tcp: hold the RCU lock across ipv6_chk_addr() in rds_tcp_laddr_check()
rds_tcp_laddr_check() looks up a scoped IPv6 interface with
dev_get_by_index_rcu(), drops the RCU read-side lock, and only then
passes the bare struct net_device * into ipv6_chk_addr().
dev_get_by_index_rcu() only keeps the device alive within the same RCU
read-side section. After rcu_read_unlock(), a concurrent RTM_DELLINK can
free the net_device; ipv6_chk_addr() then dereferences the stale pointer
in __ipv6_chk_addr_and_flags() (e.g. l3mdev_master_dev_rcu(dev)), reading
freed memory.
Keep the RCU read-side lock held across the ipv6_chk_addr() call instead
of dropping it right after the lookup, so the device cannot be freed
while it is in use.
BUG: KASAN: slab-use-after-free in __ipv6_chk_addr_and_flags (... net/ipv6/addrconf.c:1998)
Read of size 8 at addr ffff8880106ec000 by task exploit/153
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
__ipv6_chk_addr_and_flags (... net/ipv6/addrconf.c:1998)
ipv6_chk_addr (net/ipv6/addrconf.c:2031 net/ipv6/addrconf.c:1972)
rds_tcp_laddr_check (net/rds/tcp.c:370)
rds_bind (net/rds/bind.c:248)
__sys_bind (net/socket.c:1920)
__x64_sys_bind (net/socket.c:1956)
do_syscall_64 (arch/x86/entry/syscall_64.c:63)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
🎖@cveNotify
🚨 CVE-2026-74564
In the Linux kernel, the following vulnerability has been resolved:
netfilter: xt_hashlimit: validate hashtable supports XT_HASHLIMIT_RATE_MATCH
The XT_HASHLIMIT_RATE_MATCH flag mode changes the semantics of the
dsthash_ent structure which represents an entry in the hashtable. There
is a union area which uses a different layout to express the rate match
mode.
Update .checkentry path to validate the XT_HASHLIMIT_RATE_MATCH mode
flag is requested by two or more different rules that refer to the same
hashtable. Otherwise, uninitialized access to the burst field in the
union is possible.
Reject the use of the XT_HASHLIMIT_RATE_MATCH mode flag if set on by
revision less than 3 too.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
netfilter: xt_hashlimit: validate hashtable supports XT_HASHLIMIT_RATE_MATCH
The XT_HASHLIMIT_RATE_MATCH flag mode changes the semantics of the
dsthash_ent structure which represents an entry in the hashtable. There
is a union area which uses a different layout to express the rate match
mode.
Update .checkentry path to validate the XT_HASHLIMIT_RATE_MATCH mode
flag is requested by two or more different rules that refer to the same
hashtable. Otherwise, uninitialized access to the burst field in the
union is possible.
Reject the use of the XT_HASHLIMIT_RATE_MATCH mode flag if set on by
revision less than 3 too.
🎖@cveNotify
🚨 CVE-2026-74566
In the Linux kernel, the following vulnerability has been resolved:
keys: make keyring key-chunk byte order agree with keyring_diff_objects()
keyring_get_key_chunk() loads description bytes into the index chunk low
address first, while keyring_diff_objects() numbers the first differing
bit from the low end and folds the absolute byte index into the level
without removing the inline-prefix offset the level already carries.
The two disagree on byte order and bit position, so the array can be
told two keys first differ at a bit that does not differ in the chunk
the walker uses, letting crafted descriptions collide into one node.
Load the chunk in the order keyring_diff_objects() assumes and drop the
inline-prefix length when folding the byte index into the level. This
only changes the in-memory ordering used to place keys within a keyring;
add, search and read of non-colliding keys are unaffected.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
keys: make keyring key-chunk byte order agree with keyring_diff_objects()
keyring_get_key_chunk() loads description bytes into the index chunk low
address first, while keyring_diff_objects() numbers the first differing
bit from the low end and folds the absolute byte index into the level
without removing the inline-prefix offset the level already carries.
The two disagree on byte order and bit position, so the array can be
told two keys first differ at a bit that does not differ in the chunk
the walker uses, letting crafted descriptions collide into one node.
Load the chunk in the order keyring_diff_objects() assumes and drop the
inline-prefix length when folding the byte index into the level. This
only changes the in-memory ordering used to place keys within a keyring;
add, search and read of non-colliding keys are unaffected.
🎖@cveNotify
🚨 CVE-2026-74567
In the Linux kernel, the following vulnerability has been resolved:
keys: fix out-of-bounds read in keyring_get_key_chunk()
For description-level chunks keyring_get_key_chunk() advances the read
pointer by level * sizeof(long) past the inline prefix but only
bounds-checks the prefix, so a long enough key description is read past
its kmemdup(desc, desc_len + 1) allocation. Compute the full byte
offset and bounds-check the description against it before reading.
The walk only reaches a description-level chunk when two keys collide
through the hash, x, type and domain_tag chunks, so this is reached from
an unprivileged add_key(2) with a crafted pair of same-type keys whose
index hashes collide; KASAN reports a slab-out-of-bounds read.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
keys: fix out-of-bounds read in keyring_get_key_chunk()
For description-level chunks keyring_get_key_chunk() advances the read
pointer by level * sizeof(long) past the inline prefix but only
bounds-checks the prefix, so a long enough key description is read past
its kmemdup(desc, desc_len + 1) allocation. Compute the full byte
offset and bounds-check the description against it before reading.
The walk only reaches a description-level chunk when two keys collide
through the hash, x, type and domain_tag chunks, so this is reached from
an unprivileged add_key(2) with a crafted pair of same-type keys whose
index hashes collide; KASAN reports a slab-out-of-bounds read.
🎖@cveNotify
🚨 CVE-2026-74568
In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: vgic: Fix race between LPI release and re-registration
Fix a potential race between decrementing an LPI's reference count and
evicting that structure from the LPI xarray.
LPI structures are maintained in the VGIC LPI xarray (dist->lpi_xa).
When the reference count of an LPI structure drops to zero,
vgic_release_lpi_locked() removes the structure from the xarray and
frees it under the xarray lock.
However, the release of an LPI can race with a concurrent LPI
re-registration with the same INTID via vgic_add_lpi() on another CPU,
since the reference count drop and the xarray eviction are not performed
in a single atomic step. This can happen e.g. if the guest issues a
DISCARD while the LPI is still referenced from a vCPU's active-pending
list (ap_list), and the same INTID is re-mapped via MAPTI.
Particularly, vgic_release_lpi_locked() is called from two distinct
paths: direct release via vgic_put_irq(), and deferred release via
vgic_release_deleted_lpis(). During direct release, the issue can result
in deleting a newly registered LPI from the xarray:
CPU0 (Releasing LPI) CPU1 (Adding new LPI)
==================== =====================
vgic_put_irq()
__vgic_put_irq()
refcount_dec_and_test()
vgic_add_lpi()
xa_lock_irqsave()
old_irq = xa_load(.., intid)
vgic_try_get_irq_ref(old_irq) == false
new IRQ inserted --> __xa_store(.., intid, ..)
xa_unlock_irqrestore()
xa_lock_irqsave();
vgic_release_lpi_locked()
__xa_erase(.., irq->intid) <-- BUG: new IRQ is erased
kfree_rcu(old_irq)
During the deferred release path, the old IRQ can be leaked:
CPU0 (Releasing LPI) CPU1 (Adding new LPI)
==================== =====================
vgic_put_irq_norelease()
__vgic_put_irq()
refcount_dec_and_test()
irq->pending_release = true
vgic_add_lpi()
xa_lock_irqsave()
old_irq = xa_load(.., intid)
vgic_try_get_irq_ref(oldirq) == false
BUG: old IRQ overwritten --> __xa_store(.., intid, ..)
xa_unlock_irqrestore()
vgic_release_deleted_lpis()
xa_lock_irqsave()
xa_for_each() { .. } <-- old IRQ with pending_release = true
is gone, so it cannot be released
To fix the direct release path, move the reference count drop inside
the xarray lock, making sure that vgic_add_lpi() never encounters the
to-be-released LPI.
In the deferred release path, the refcount drop must happen under a raw
spinlock, so the xarray lock cannot be grabbed, and the same solution
does not work. Instead, update vgic_add_lpi(), so that if it evicts
an LPI from the xarray, it takes on the responsibility of freeing it.
Consequently, an LPI may now be freed concurrently after a deferred
release drops the refcount, so accessing the pending_release field is no
longer safe from use-after-free. Delete all uses of the flag, and update
vgic_release_deleted_lpis() to identify orphaned LPIs purely based on
their refcount.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: vgic: Fix race between LPI release and re-registration
Fix a potential race between decrementing an LPI's reference count and
evicting that structure from the LPI xarray.
LPI structures are maintained in the VGIC LPI xarray (dist->lpi_xa).
When the reference count of an LPI structure drops to zero,
vgic_release_lpi_locked() removes the structure from the xarray and
frees it under the xarray lock.
However, the release of an LPI can race with a concurrent LPI
re-registration with the same INTID via vgic_add_lpi() on another CPU,
since the reference count drop and the xarray eviction are not performed
in a single atomic step. This can happen e.g. if the guest issues a
DISCARD while the LPI is still referenced from a vCPU's active-pending
list (ap_list), and the same INTID is re-mapped via MAPTI.
Particularly, vgic_release_lpi_locked() is called from two distinct
paths: direct release via vgic_put_irq(), and deferred release via
vgic_release_deleted_lpis(). During direct release, the issue can result
in deleting a newly registered LPI from the xarray:
CPU0 (Releasing LPI) CPU1 (Adding new LPI)
==================== =====================
vgic_put_irq()
__vgic_put_irq()
refcount_dec_and_test()
vgic_add_lpi()
xa_lock_irqsave()
old_irq = xa_load(.., intid)
vgic_try_get_irq_ref(old_irq) == false
new IRQ inserted --> __xa_store(.., intid, ..)
xa_unlock_irqrestore()
xa_lock_irqsave();
vgic_release_lpi_locked()
__xa_erase(.., irq->intid) <-- BUG: new IRQ is erased
kfree_rcu(old_irq)
During the deferred release path, the old IRQ can be leaked:
CPU0 (Releasing LPI) CPU1 (Adding new LPI)
==================== =====================
vgic_put_irq_norelease()
__vgic_put_irq()
refcount_dec_and_test()
irq->pending_release = true
vgic_add_lpi()
xa_lock_irqsave()
old_irq = xa_load(.., intid)
vgic_try_get_irq_ref(oldirq) == false
BUG: old IRQ overwritten --> __xa_store(.., intid, ..)
xa_unlock_irqrestore()
vgic_release_deleted_lpis()
xa_lock_irqsave()
xa_for_each() { .. } <-- old IRQ with pending_release = true
is gone, so it cannot be released
To fix the direct release path, move the reference count drop inside
the xarray lock, making sure that vgic_add_lpi() never encounters the
to-be-released LPI.
In the deferred release path, the refcount drop must happen under a raw
spinlock, so the xarray lock cannot be grabbed, and the same solution
does not work. Instead, update vgic_add_lpi(), so that if it evicts
an LPI from the xarray, it takes on the responsibility of freeing it.
Consequently, an LPI may now be freed concurrently after a deferred
release drops the refcount, so accessing the pending_release field is no
longer safe from use-after-free. Delete all uses of the flag, and update
vgic_release_deleted_lpis() to identify orphaned LPIs purely based on
their refcount.
🎖@cveNotify
🚨 CVE-2026-74569
In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_conntrack_sip: widen NAT rewrite delta to s32 in sip_help_tcp()
sip_help_tcp() stores the size change of each NAT-rewritten SIP message
in s16 diff and accumulates it in s16 tdiff, but a single message can
grow by more than S16_MAX while the packet stays under the 65535
enlarge_skb() limit: nf_nat_sip() rewrites every matching URI, and a long
Contact list expands the message by tens of kilobytes. diff then wraps,
and "datalen = datalen + diff - msglen" yields a huge unsigned datalen,
so the next iteration's ct_sip_get_header() reads past the linearized skb
tail.
Widen diff, tdiff and the seq_adjust hook to s32. Both are bounded by the
65535 byte packet limit, and the seqadj core is already s32
(nf_ct_seqadj_set() takes s32), so no previously accepted input is
rejected.
BUG: KASAN: use-after-free in ct_sip_get_header (net/netfilter/nf_conntrack_sip.c:464)
Read of size 1 at addr ffff888010800000 by task ksoftirqd/1/25
ct_sip_get_header (net/netfilter/nf_conntrack_sip.c:464)
sip_help_tcp (net/netfilter/nf_conntrack_sip.c:1694)
nf_confirm (net/netfilter/nf_conntrack_proto.c:183)
nf_hook_slow (net/netfilter/core.c:619)
ip6_output (net/ipv6/ip6_output.c:246)
ip6_forward (net/ipv6/ip6_output.c:690)
ipv6_rcv (net/ipv6/ip6_input.c:351)
__netif_receive_skb_one_core (net/core/dev.c:6212)
process_backlog (net/core/dev.c:6676)
__napi_poll (net/core/dev.c:7735)
net_rx_action (net/core/dev.c:7955)
handle_softirqs (kernel/softirq.c:622)
run_ksoftirqd (kernel/softirq.c:1076)
...
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_conntrack_sip: widen NAT rewrite delta to s32 in sip_help_tcp()
sip_help_tcp() stores the size change of each NAT-rewritten SIP message
in s16 diff and accumulates it in s16 tdiff, but a single message can
grow by more than S16_MAX while the packet stays under the 65535
enlarge_skb() limit: nf_nat_sip() rewrites every matching URI, and a long
Contact list expands the message by tens of kilobytes. diff then wraps,
and "datalen = datalen + diff - msglen" yields a huge unsigned datalen,
so the next iteration's ct_sip_get_header() reads past the linearized skb
tail.
Widen diff, tdiff and the seq_adjust hook to s32. Both are bounded by the
65535 byte packet limit, and the seqadj core is already s32
(nf_ct_seqadj_set() takes s32), so no previously accepted input is
rejected.
BUG: KASAN: use-after-free in ct_sip_get_header (net/netfilter/nf_conntrack_sip.c:464)
Read of size 1 at addr ffff888010800000 by task ksoftirqd/1/25
ct_sip_get_header (net/netfilter/nf_conntrack_sip.c:464)
sip_help_tcp (net/netfilter/nf_conntrack_sip.c:1694)
nf_confirm (net/netfilter/nf_conntrack_proto.c:183)
nf_hook_slow (net/netfilter/core.c:619)
ip6_output (net/ipv6/ip6_output.c:246)
ip6_forward (net/ipv6/ip6_output.c:690)
ipv6_rcv (net/ipv6/ip6_input.c:351)
__netif_receive_skb_one_core (net/core/dev.c:6212)
process_backlog (net/core/dev.c:6676)
__napi_poll (net/core/dev.c:7735)
net_rx_action (net/core/dev.c:7955)
handle_softirqs (kernel/softirq.c:622)
run_ksoftirqd (kernel/softirq.c:1076)
...
🎖@cveNotify
🚨 CVE-2026-74570
In the Linux kernel, the following vulnerability has been resolved:
ntfs: harden runlist realloc size calculations
Add a shared helper to safely convert runlist element counts to byte sizes
using overflow checks, and use it in both ntfs_rl_realloc() and
ntfs_rl_realloc_nofail().
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
ntfs: harden runlist realloc size calculations
Add a shared helper to safely convert runlist element counts to byte sizes
using overflow checks, and use it in both ntfs_rl_realloc() and
ntfs_rl_realloc_nofail().
🎖@cveNotify
🚨 CVE-2026-74571
In the Linux kernel, the following vulnerability has been resolved:
btrfs: skip global block reserve accounting for rescue mounts
[BUG]
Mounting with rescue=ibadroots after corrupting the block group tree
root triggers a NULL pointer dereference:
BUG: kernel NULL pointer dereference, address: 0000000000000100
RIP: 0010:btrfs_update_global_block_rsv+0x9d/0x1c0 [btrfs]
Call Trace:
fill_dummy_bgs+0xd4/0x120 [btrfs]
open_ctree+0xc6e/0x1ca0 [btrfs]
btrfs_get_tree+0x50d/0xa40 [btrfs]
The same crash occurs with a corrupted raid stripe tree root, via
btrfs_read_block_groups() instead of fill_dummy_bgs().
[CAUSE]
With rescue=ibadroots, btrfs_read_roots() allows the mount to continue
when either root cannot be read, leaving the corresponding root pointer
NULL while its on-disk feature bit remains set.
btrfs_update_global_block_rsv() then dereferences the missing root based
on the feature bit alone.
[FIX]
Rescue mounts are fully read-only and cannot start transactions, so the
global reserve is never consumed. Under btrfs_is_full_ro(), mark the
reserve as full and return before performing the accounting.
And since we need to check if the fs is mount fully RO, export
fs_is_full_ro() as btrfs_is_full_ro(), and move it to fs.h.
[ Squash the fs_is_full_ro() export commit into this one. ]
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
btrfs: skip global block reserve accounting for rescue mounts
[BUG]
Mounting with rescue=ibadroots after corrupting the block group tree
root triggers a NULL pointer dereference:
BUG: kernel NULL pointer dereference, address: 0000000000000100
RIP: 0010:btrfs_update_global_block_rsv+0x9d/0x1c0 [btrfs]
Call Trace:
fill_dummy_bgs+0xd4/0x120 [btrfs]
open_ctree+0xc6e/0x1ca0 [btrfs]
btrfs_get_tree+0x50d/0xa40 [btrfs]
The same crash occurs with a corrupted raid stripe tree root, via
btrfs_read_block_groups() instead of fill_dummy_bgs().
[CAUSE]
With rescue=ibadroots, btrfs_read_roots() allows the mount to continue
when either root cannot be read, leaving the corresponding root pointer
NULL while its on-disk feature bit remains set.
btrfs_update_global_block_rsv() then dereferences the missing root based
on the feature bit alone.
[FIX]
Rescue mounts are fully read-only and cannot start transactions, so the
global reserve is never consumed. Under btrfs_is_full_ro(), mark the
reserve as full and return before performing the accounting.
And since we need to check if the fs is mount fully RO, export
fs_is_full_ro() as btrfs_is_full_ro(), and move it to fs.h.
[ Squash the fs_is_full_ro() export commit into this one. ]
🎖@cveNotify
🚨 CVE-2026-74572
In the Linux kernel, the following vulnerability has been resolved:
btrfs: zoned: fix deadlock between metadata writeback and transaction commit
When writing out metadata extent buffers in a zoned filesystem,
btree_writepages() holds fs_info->zoned_meta_io_lock across the whole
writeback loop, including the call to btrfs_check_meta_write_pointer() ->
check_bg_is_active().
For the tree-log block group, check_bg_is_active() may fail to activate
the zone and fall back to btrfs_zone_finish_one_bg() to free an active
zone. That path waits for the running transaction to commit while still
holding zoned_meta_io_lock, but the committer needs that same lock to
write out the tree extents, so the two tasks deadlock:
Task A (kworker, metadata writeback) Task B (fsstress, transaction commit)
------------------------------------ -------------------------------------
wb_workfn() btrfs_commit_transaction(T)
btree_writepages() btrfs_write_and_wait_transaction()
btrfs_zoned_meta_io_lock() btrfs_write_marked_extents()
btrfs_check_meta_write_pointer() btree_writepages()
check_bg_is_active() [treelog_bg] btrfs_zoned_meta_io_lock()
btrfs_zone_finish_one_bg() <blocks on zoned_meta_io_lock,
btrfs_zone_finish() held by Task A>
do_zone_finish()
btrfs_inc_block_group_ro()
btrfs_wait_for_commit()
<blocks waiting for commit
of transaction T, done by
Task B>
The sibling branch in check_bg_is_active() already drops zoned_meta_io_lock
around do_zone_finish() for this exact reason. Do the same in the tree-log
branch: release the lock around btrfs_zone_finish_one_bg() and re-acquire
it afterwards. The lock only protects fs_info->active_{meta,system}_bg,
which this branch does not touch, and ctx->zoned_bg keeps a reference to
the block group across the unlock, so nothing is lost while the lock
is dropped.
This hang occasionally reproduces with fstests generic/475 on a zoned
btrfs filesystem.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
btrfs: zoned: fix deadlock between metadata writeback and transaction commit
When writing out metadata extent buffers in a zoned filesystem,
btree_writepages() holds fs_info->zoned_meta_io_lock across the whole
writeback loop, including the call to btrfs_check_meta_write_pointer() ->
check_bg_is_active().
For the tree-log block group, check_bg_is_active() may fail to activate
the zone and fall back to btrfs_zone_finish_one_bg() to free an active
zone. That path waits for the running transaction to commit while still
holding zoned_meta_io_lock, but the committer needs that same lock to
write out the tree extents, so the two tasks deadlock:
Task A (kworker, metadata writeback) Task B (fsstress, transaction commit)
------------------------------------ -------------------------------------
wb_workfn() btrfs_commit_transaction(T)
btree_writepages() btrfs_write_and_wait_transaction()
btrfs_zoned_meta_io_lock() btrfs_write_marked_extents()
btrfs_check_meta_write_pointer() btree_writepages()
check_bg_is_active() [treelog_bg] btrfs_zoned_meta_io_lock()
btrfs_zone_finish_one_bg() <blocks on zoned_meta_io_lock,
btrfs_zone_finish() held by Task A>
do_zone_finish()
btrfs_inc_block_group_ro()
btrfs_wait_for_commit()
<blocks waiting for commit
of transaction T, done by
Task B>
The sibling branch in check_bg_is_active() already drops zoned_meta_io_lock
around do_zone_finish() for this exact reason. Do the same in the tree-log
branch: release the lock around btrfs_zone_finish_one_bg() and re-acquire
it afterwards. The lock only protects fs_info->active_{meta,system}_bg,
which this branch does not touch, and ctx->zoned_bg keeps a reference to
the block group across the unlock, so nothing is lost while the lock
is dropped.
This hang occasionally reproduces with fstests generic/475 on a zoned
btrfs filesystem.
🎖@cveNotify
🚨 CVE-2026-74573
In the Linux kernel, the following vulnerability has been resolved:
iommu/arm-smmu-v3-iommufd: Require exactly one Stream ID for a vDEVICE
arm_vsmmu_vsid_to_sid() maps a guest's vSID to a single physical Stream ID
taken from master->streams[0], assuming a device has exactly one stream. A
device with several streams gets only its first one mapped, so a guest vSID
invalidation cannot reach the others' ATC and IOTLB entries; a device with
none makes master->streams a ZERO_SIZE_PTR, read out of bounds.
Add an arm_vsmmu_vdevice_init() op to reject the vDEVICE with -EOPNOTSUPP
when master->num_streams is not one, rather than mapping it silently.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
iommu/arm-smmu-v3-iommufd: Require exactly one Stream ID for a vDEVICE
arm_vsmmu_vsid_to_sid() maps a guest's vSID to a single physical Stream ID
taken from master->streams[0], assuming a device has exactly one stream. A
device with several streams gets only its first one mapped, so a guest vSID
invalidation cannot reach the others' ATC and IOTLB entries; a device with
none makes master->streams a ZERO_SIZE_PTR, read out of bounds.
Add an arm_vsmmu_vdevice_init() op to reject the vDEVICE with -EOPNOTSUPP
when master->num_streams is not one, rather than mapping it silently.
🎖@cveNotify
🚨 CVE-2026-74574
In the Linux kernel, the following vulnerability has been resolved:
dmaengine: idxd: fix fdev setup failure cleanup in idxd_cdev_open()
The failed_dev_add and failed_dev_name paths drop the file-device
reference while wq->wq_lock is still held. If put_device(fdev) drops the
last reference, idxd_file_dev_release() runs synchronously and tries to
take wq->wq_lock again, deadlocking.
Those paths also fall through into the later ctx cleanup labels even
though idxd_file_dev_release() owns that cleanup and frees ctx. This can
make idxd_xa_pasid_remove(ctx) and kfree(ctx) operate on a freed context.
Move idxd_wq_get() before file-device setup can fail, since the release
callback always calls idxd_wq_put(). Then unlock wq->wq_lock before
put_device(fdev) and return directly from the file-device setup failure
path, leaving ctx cleanup to the release callback.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
dmaengine: idxd: fix fdev setup failure cleanup in idxd_cdev_open()
The failed_dev_add and failed_dev_name paths drop the file-device
reference while wq->wq_lock is still held. If put_device(fdev) drops the
last reference, idxd_file_dev_release() runs synchronously and tries to
take wq->wq_lock again, deadlocking.
Those paths also fall through into the later ctx cleanup labels even
though idxd_file_dev_release() owns that cleanup and frees ctx. This can
make idxd_xa_pasid_remove(ctx) and kfree(ctx) operate on a freed context.
Move idxd_wq_get() before file-device setup can fail, since the release
callback always calls idxd_wq_put(). Then unlock wq->wq_lock before
put_device(fdev) and return directly from the file-device setup failure
path, leaving ctx cleanup to the release callback.
🎖@cveNotify
🚨 CVE-2026-74575
In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Prevent XDomain delayed work use-after-free on disconnect
tb_xdp_handle_request() runs on system_wq and queues
xd->state_work via queue_delayed_work() in three request handlers:
PROPERTIES_CHANGED_REQUEST, UUID_REQUEST (via start_handshake),
and LINK_STATE_CHANGE_REQUEST. Similarly, update_xdomain() queues
xd->properties_changed_work when local properties change.
Concurrently, tb_xdomain_remove() calls stop_handshake() which does
cancel_delayed_work_sync() on both delayed works. Later,
tb_xdomain_unregister() calls device_unregister() which eventually
frees the xdomain. Since commit 559c1e1e0134 ("thunderbolt: Run
tb_xdp_handle_request() in system workqueue") moved the request
handler off tb->wq, the handler and the remove path are no longer
serialized. If queue_delayed_work() executes after
cancel_delayed_work_sync() but before the xdomain is freed, the
delayed work fires on a freed object.
Add xd->removing that tb_xdomain_remove() sets under xd->lock
before calling stop_handshake(). Each external queue site holds
the same lock and checks removing before calling
queue_delayed_work(). This provides the mutual exclusion needed:
either the queue site acquires the lock first and queues work that
the subsequent cancel will see, or the remove path acquires the
lock first and the queue site observes removing == true and skips
the queue.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Prevent XDomain delayed work use-after-free on disconnect
tb_xdp_handle_request() runs on system_wq and queues
xd->state_work via queue_delayed_work() in three request handlers:
PROPERTIES_CHANGED_REQUEST, UUID_REQUEST (via start_handshake),
and LINK_STATE_CHANGE_REQUEST. Similarly, update_xdomain() queues
xd->properties_changed_work when local properties change.
Concurrently, tb_xdomain_remove() calls stop_handshake() which does
cancel_delayed_work_sync() on both delayed works. Later,
tb_xdomain_unregister() calls device_unregister() which eventually
frees the xdomain. Since commit 559c1e1e0134 ("thunderbolt: Run
tb_xdp_handle_request() in system workqueue") moved the request
handler off tb->wq, the handler and the remove path are no longer
serialized. If queue_delayed_work() executes after
cancel_delayed_work_sync() but before the xdomain is freed, the
delayed work fires on a freed object.
Add xd->removing that tb_xdomain_remove() sets under xd->lock
before calling stop_handshake(). Each external queue site holds
the same lock and checks removing before calling
queue_delayed_work(). This provides the mutual exclusion needed:
either the queue site acquires the lock first and queues work that
the subsequent cancel will see, or the remove path acquires the
lock first and the queue site observes removing == true and skips
the queue.
🎖@cveNotify
🚨 CVE-2026-74576
In the Linux kernel, the following vulnerability has been resolved:
mm/slab: prevent unbounded recursion in free path with new kmalloc type
Commit 280ea9c3154b ("mm/slab: avoid allocating slabobj_ext array from
its own slab") avoided recursive allocation of obj_exts from kmalloc
caches of the same size, by bumping the obj_exts array's allocation
size whenever the array size equals the size of the object being
allocated.
However, as reported by Danielle Costantino and Shakeel Butt,
even slabs from kmalloc caches of different sizes can form a cycle
by allocating obj_exts arrays from each other [1]:
What happened: a KMALLOC_NORMAL slab's obj_exts array (used by
allocation profiling / memcg accounting) is itself kmalloc()'d from a
KMALLOC_NORMAL cache, so the "slab holds another slab's obj_exts array"
relation can form cycles. With sizeof(struct slabobj_ext) == 16 and
the host's geometry:
- kmalloc-512 has 64 objects/slab -> array is 64*16 == 1024 bytes,
served from kmalloc-1k;
- kmalloc-1k has 32 objects/slab -> array is 32*16 == 512 bytes,
served from kmalloc-512.
A kmalloc-512 slab and a kmalloc-1k slab therefore hold each other's
obj_exts array. Discarding one frees the other's array, which empties
and discards that slab, which frees the first's array, and so on:
__free_slab() -> free_slab_obj_exts() -> kfree() -> discard_slab() ->
__free_slab() recurses along the cycle until the stack is exhausted.
With memory allocation profiling, this allows unbounded recursion
in the free path and led to a stack overflow on a production host in
the Meta fleet [1]:
BUG: TASK stack guard page was hit
Oops: stack guard page
RIP: 0010:kfree+0x8/0x5d0
Call Trace:
__free_slab+0x66/0xc0
kfree+0x3f0/0x5d0
... ( ~125x __free_slab <-> kfree ) ...
<kernel driver freeing a resource>
do_syscall_64
It is proposed [1] to resolve this issue by always serving the obj_exts
array allocation from kmalloc caches (or large kmalloc) of sizes larger
than the object size. However, as pointed out by Vlastimil Babka [2],
this can waste an excessive amount of memory as slabs from large
kmalloc sizes (e.g. kmalloc-8k) generally need obj_exts arrays much
smaller than the object size.
Therefore, rather than bumping the size, let us take a different
approach; disallow formation of cycles between kmalloc types when
allocating obj_exts arrays. Currently, all obj_exts arrays are served
from normal kmalloc caches. Cycles cannot be created if obj_exts arrays
of normal kmalloc caches are served from a special kmalloc type that can
never have obj_exts arrays.
To achieve this, create a new kmalloc type called KMALLOC_NO_OBJ_EXT.
KMALLOC_NO_OBJ_EXT caches are created with SLAB_NO_OBJ_EXT flag when
either 1) memory allocation profiling is not permanently disabled,
or 2) kmalloc types with a priority higher than KMALLOC_CGROUP are
aliased with KMALLOC_NORMAL.
Sheaf bootstrapping for KMALLOC_NO_OBJ_EXT caches now must be deferred
because allocation of a barn can trigger obj_exts array allocation of
normal kmalloc caches when the KMALLOC_NO_OBJ_EXT cache for that size
is not ready yet. For simplicity, perform bootstrapping of sheaves for
all kmalloc caches later.
Introduce a new slab alloc flag, SLAB_ALLOC_NO_OBJ_EXT, to prevent
allocation of obj_exts arrays, and let kmalloc_slab() override the type
to KMALLOC_NO_OBJ_EXT when specified. Note that kmalloc_type() remains
unchanged because kmalloc_flags() bypasses the kmalloc fastpath.
Do not pass SLAB_ALLOC_NO_RECURSE to kmalloc_flags() in
alloc_slab_obj_exts() and instead use SLAB_ALLOC_NO_OBJ_EXT only when
the objects are allocated from normal kmalloc caches. While this
prevents unbounded recursive allocation of obj_exts, it allows
KMALLOC_NO_OBJ_EXT caches to have sheaves.
Since sheaf allocations specify SLAB_ALLOC_NO_RECURSE that prevents
allocation of both sheaves and obj_exts arrays, the recursion depth
is bounded.
obj_exts arrays for non-
---truncated---
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
mm/slab: prevent unbounded recursion in free path with new kmalloc type
Commit 280ea9c3154b ("mm/slab: avoid allocating slabobj_ext array from
its own slab") avoided recursive allocation of obj_exts from kmalloc
caches of the same size, by bumping the obj_exts array's allocation
size whenever the array size equals the size of the object being
allocated.
However, as reported by Danielle Costantino and Shakeel Butt,
even slabs from kmalloc caches of different sizes can form a cycle
by allocating obj_exts arrays from each other [1]:
What happened: a KMALLOC_NORMAL slab's obj_exts array (used by
allocation profiling / memcg accounting) is itself kmalloc()'d from a
KMALLOC_NORMAL cache, so the "slab holds another slab's obj_exts array"
relation can form cycles. With sizeof(struct slabobj_ext) == 16 and
the host's geometry:
- kmalloc-512 has 64 objects/slab -> array is 64*16 == 1024 bytes,
served from kmalloc-1k;
- kmalloc-1k has 32 objects/slab -> array is 32*16 == 512 bytes,
served from kmalloc-512.
A kmalloc-512 slab and a kmalloc-1k slab therefore hold each other's
obj_exts array. Discarding one frees the other's array, which empties
and discards that slab, which frees the first's array, and so on:
__free_slab() -> free_slab_obj_exts() -> kfree() -> discard_slab() ->
__free_slab() recurses along the cycle until the stack is exhausted.
With memory allocation profiling, this allows unbounded recursion
in the free path and led to a stack overflow on a production host in
the Meta fleet [1]:
BUG: TASK stack guard page was hit
Oops: stack guard page
RIP: 0010:kfree+0x8/0x5d0
Call Trace:
__free_slab+0x66/0xc0
kfree+0x3f0/0x5d0
... ( ~125x __free_slab <-> kfree ) ...
<kernel driver freeing a resource>
do_syscall_64
It is proposed [1] to resolve this issue by always serving the obj_exts
array allocation from kmalloc caches (or large kmalloc) of sizes larger
than the object size. However, as pointed out by Vlastimil Babka [2],
this can waste an excessive amount of memory as slabs from large
kmalloc sizes (e.g. kmalloc-8k) generally need obj_exts arrays much
smaller than the object size.
Therefore, rather than bumping the size, let us take a different
approach; disallow formation of cycles between kmalloc types when
allocating obj_exts arrays. Currently, all obj_exts arrays are served
from normal kmalloc caches. Cycles cannot be created if obj_exts arrays
of normal kmalloc caches are served from a special kmalloc type that can
never have obj_exts arrays.
To achieve this, create a new kmalloc type called KMALLOC_NO_OBJ_EXT.
KMALLOC_NO_OBJ_EXT caches are created with SLAB_NO_OBJ_EXT flag when
either 1) memory allocation profiling is not permanently disabled,
or 2) kmalloc types with a priority higher than KMALLOC_CGROUP are
aliased with KMALLOC_NORMAL.
Sheaf bootstrapping for KMALLOC_NO_OBJ_EXT caches now must be deferred
because allocation of a barn can trigger obj_exts array allocation of
normal kmalloc caches when the KMALLOC_NO_OBJ_EXT cache for that size
is not ready yet. For simplicity, perform bootstrapping of sheaves for
all kmalloc caches later.
Introduce a new slab alloc flag, SLAB_ALLOC_NO_OBJ_EXT, to prevent
allocation of obj_exts arrays, and let kmalloc_slab() override the type
to KMALLOC_NO_OBJ_EXT when specified. Note that kmalloc_type() remains
unchanged because kmalloc_flags() bypasses the kmalloc fastpath.
Do not pass SLAB_ALLOC_NO_RECURSE to kmalloc_flags() in
alloc_slab_obj_exts() and instead use SLAB_ALLOC_NO_OBJ_EXT only when
the objects are allocated from normal kmalloc caches. While this
prevents unbounded recursive allocation of obj_exts, it allows
KMALLOC_NO_OBJ_EXT caches to have sheaves.
Since sheaf allocations specify SLAB_ALLOC_NO_RECURSE that prevents
allocation of both sheaves and obj_exts arrays, the recursion depth
is bounded.
obj_exts arrays for non-
---truncated---
🎖@cveNotify
🚨 CVE-2026-74577
In the Linux kernel, the following vulnerability has been resolved:
net: mpls: initialize rtm_tos in mpls_getroute()
mpls_getroute() builds the RTM_NEWROUTE reply to an RTM_GETROUTE
request by filling a struct rtmsg allocated from an skb whose data
area is not zeroed (alloc_skb(NLMSG_GOODSIZE, ...)). It sets every
field of the header except rtm_tos:
r = nlmsg_data(nlh);
r->rtm_family = AF_MPLS;
r->rtm_dst_len = 20;
r->rtm_src_len = 0;
r->rtm_table = RT_TABLE_MAIN;
r->rtm_type = RTN_UNICAST;
r->rtm_scope = RT_SCOPE_UNIVERSE;
r->rtm_protocol = rt->rt_protocol;
r->rtm_flags = 0;
struct rtmsg has no padding, so the one uninitialised byte rtm_tos
(offset 3) is copied straight to user space on recvmsg(), leaking a
byte of uninitialised heap memory. This is in contrast to
mpls_dump_route(), which fills the very same header and does set
rtm_tos = 0.
Initialize rtm_tos to 0, matching mpls_dump_route().
Reproduced with KMSAN by adding an MPLS route and issuing a
non-RTM_F_FIB_MATCH RTM_GETROUTE for its label:
BUG: KMSAN: kernel-infoleak in _copy_to_iter+0x36c/0x33f0
_copy_to_iter+0x36c/0x33f0
__skb_datagram_iter+0x196/0x12c0
skb_copy_datagram_iter+0x5b/0x210
netlink_recvmsg+0x37b/0xef0
...
Uninit was created at:
__alloc_skb+0x8ca/0x10e0
mpls_getroute+0x1280/0x3a40
rtnetlink_rcv_msg+0x1138/0x15a0
...
Byte 19 of 64 is uninitialized
(byte 19 = nlmsghdr(16) + rtmsg offset 3 = rtm_tos)
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
net: mpls: initialize rtm_tos in mpls_getroute()
mpls_getroute() builds the RTM_NEWROUTE reply to an RTM_GETROUTE
request by filling a struct rtmsg allocated from an skb whose data
area is not zeroed (alloc_skb(NLMSG_GOODSIZE, ...)). It sets every
field of the header except rtm_tos:
r = nlmsg_data(nlh);
r->rtm_family = AF_MPLS;
r->rtm_dst_len = 20;
r->rtm_src_len = 0;
r->rtm_table = RT_TABLE_MAIN;
r->rtm_type = RTN_UNICAST;
r->rtm_scope = RT_SCOPE_UNIVERSE;
r->rtm_protocol = rt->rt_protocol;
r->rtm_flags = 0;
struct rtmsg has no padding, so the one uninitialised byte rtm_tos
(offset 3) is copied straight to user space on recvmsg(), leaking a
byte of uninitialised heap memory. This is in contrast to
mpls_dump_route(), which fills the very same header and does set
rtm_tos = 0.
Initialize rtm_tos to 0, matching mpls_dump_route().
Reproduced with KMSAN by adding an MPLS route and issuing a
non-RTM_F_FIB_MATCH RTM_GETROUTE for its label:
BUG: KMSAN: kernel-infoleak in _copy_to_iter+0x36c/0x33f0
_copy_to_iter+0x36c/0x33f0
__skb_datagram_iter+0x196/0x12c0
skb_copy_datagram_iter+0x5b/0x210
netlink_recvmsg+0x37b/0xef0
...
Uninit was created at:
__alloc_skb+0x8ca/0x10e0
mpls_getroute+0x1280/0x3a40
rtnetlink_rcv_msg+0x1138/0x15a0
...
Byte 19 of 64 is uninitialized
(byte 19 = nlmsghdr(16) + rtmsg offset 3 = rtm_tos)
🎖@cveNotify
🚨 CVE-2026-74578
In the Linux kernel, the following vulnerability has been resolved:
crypto: algif_skcipher - force synchronous processing on trees without ctx->state
The AIO/async path in skcipher_recvmsg() passes the socket-wide ctx->iv
directly into the skcipher request. After io_submit() the socket lock is
dropped and the request is processed asynchronously, so a concurrent
sendmsg(ALG_SET_IV) can overwrite ctx->iv and make the in-flight request
run under an attacker-controlled IV. For CTR/stream modes this is
IV/keystream reuse and lets an unprivileged user recover the plaintext of
a concurrent operation.
Snapshotting ctx->iv into per-request storage for the async path is not
sufficient. For ciphers with statesize == 0 - which includes cbc and ctr -
the MSG_MORE inter-chunk IV chaining is carried solely by the in-place
req->iv writeback, which a snapshot redirects into per-request memory that
af_alg_free_resources() releases on completion, silently producing wrong
output. Writing the IV back from the completion callback instead is not
possible either: that would require lock_sock() there, but the callback can
run in softirq/atomic context, so it must not sleep.
Make the operation synchronous instead, which removes both the IV race and
any writeback race. This is equivalent to the upstream resolution, commit
fcc77d33a34c ("net: Remove support for AIO on sockets"), which removed the
AIO socket path across net/ entirely and so produces the same end state for
this file. This patch deviates from that commit deliberately: rather than
removing AIO socket support tree-wide, which would be far too invasive for
stable, it removes only the AIO branch in crypto/algif_skcipher.c.
io_submit() now completes synchronously; AF_ALG async is rarely used in
practice.
The -EIOCBQUEUED check in skcipher_recvmsg() is now dead but harmless,
and is left alone to keep the fix minimal.
Tested on 6.6.y: attacker IV injection dropped from 2296/200000 to 0/200000
after the change; MSG_MORE chunked CTR output bit-identical to single-shot.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
crypto: algif_skcipher - force synchronous processing on trees without ctx->state
The AIO/async path in skcipher_recvmsg() passes the socket-wide ctx->iv
directly into the skcipher request. After io_submit() the socket lock is
dropped and the request is processed asynchronously, so a concurrent
sendmsg(ALG_SET_IV) can overwrite ctx->iv and make the in-flight request
run under an attacker-controlled IV. For CTR/stream modes this is
IV/keystream reuse and lets an unprivileged user recover the plaintext of
a concurrent operation.
Snapshotting ctx->iv into per-request storage for the async path is not
sufficient. For ciphers with statesize == 0 - which includes cbc and ctr -
the MSG_MORE inter-chunk IV chaining is carried solely by the in-place
req->iv writeback, which a snapshot redirects into per-request memory that
af_alg_free_resources() releases on completion, silently producing wrong
output. Writing the IV back from the completion callback instead is not
possible either: that would require lock_sock() there, but the callback can
run in softirq/atomic context, so it must not sleep.
Make the operation synchronous instead, which removes both the IV race and
any writeback race. This is equivalent to the upstream resolution, commit
fcc77d33a34c ("net: Remove support for AIO on sockets"), which removed the
AIO socket path across net/ entirely and so produces the same end state for
this file. This patch deviates from that commit deliberately: rather than
removing AIO socket support tree-wide, which would be far too invasive for
stable, it removes only the AIO branch in crypto/algif_skcipher.c.
io_submit() now completes synchronously; AF_ALG async is rarely used in
practice.
The -EIOCBQUEUED check in skcipher_recvmsg() is now dead but harmless,
and is left alone to keep the fix minimal.
Tested on 6.6.y: attacker IV injection dropped from 2296/200000 to 0/200000
after the change; MSG_MORE chunked CTR output bit-identical to single-shot.
🎖@cveNotify
🚨 CVE-2026-13700
The WooMS WordPress plugin through 9.14 does not validate a user-supplied URL before using it in a server-side request and attaches stored third-party integration credentials to every such request, allowing unauthenticated attackers to perform Server-Side Request Forgery and to disclose the configured integration credentials when the relevant data-sync feature is enabled.
🎖@cveNotify
The WooMS WordPress plugin through 9.14 does not validate a user-supplied URL before using it in a server-side request and attaches stored third-party integration credentials to every such request, allowing unauthenticated attackers to perform Server-Side Request Forgery and to disclose the configured integration credentials when the relevant data-sync feature is enabled.
🎖@cveNotify
WPScan
WooMS <= 9.14 - Unauthenticated Server-Side Request Forgery and Sensitive Information Disclosure
See details on WooMS <= 9.14 - Unauthenticated Server-Side Request Forgery and Sensitive Information Disclosure CVE 2026-13700. View the latest Plugin Vulnerabilities on WPScan.
🚨 CVE-2026-14832
The ShopSmart Loyalty for WooCommerce WordPress plugin through 1.0.0 does not perform any authorization or ownership check on a phone-number lookup exposed to unauthenticated users, allowing anyone who knows a customer's phone number to retrieve that customer's loyalty profile, including name, email, and account balance.
🎖@cveNotify
The ShopSmart Loyalty for WooCommerce WordPress plugin through 1.0.0 does not perform any authorization or ownership check on a phone-number lookup exposed to unauthenticated users, allowing anyone who knows a customer's phone number to retrieve that customer's loyalty profile, including name, email, and account balance.
🎖@cveNotify
WPScan
ShopSmart Loyalty for WooCommerce <= 1.0.0 - Unauthenticated Sensitive Information Disclosure via shopsmart_check_phone
See details on ShopSmart Loyalty for WooCommerce <= 1.0.0 - Unauthenticated Sensitive Information Disclosure via shopsmart_check_phone CVE 2026-14832. View the latest Plugin Vulnerabilities on WPScan.