🚨 CVE-2023-52502
In the Linux kernel, the following vulnerability has been resolved:
net: nfc: fix races in nfc_llcp_sock_get() and nfc_llcp_sock_get_sn()
Sili Luo reported a race in nfc_llcp_sock_get(), leading to UAF.
Getting a reference on the socket found in a lookup while
holding a lock should happen before releasing the lock.
nfc_llcp_sock_get_sn() has a similar problem.
Finally nfc_llcp_recv_snl() needs to make sure the socket
found by nfc_llcp_sock_from_sn() does not disappear.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
net: nfc: fix races in nfc_llcp_sock_get() and nfc_llcp_sock_get_sn()
Sili Luo reported a race in nfc_llcp_sock_get(), leading to UAF.
Getting a reference on the socket found in a lookup while
holding a lock should happen before releasing the lock.
nfc_llcp_sock_get_sn() has a similar problem.
Finally nfc_llcp_recv_snl() needs to make sure the socket
found by nfc_llcp_sock_from_sn() does not disappear.
🎖@cveNotify
🚨 CVE-2023-52503
In the Linux kernel, the following vulnerability has been resolved:
tee: amdtee: fix use-after-free vulnerability in amdtee_close_session
There is a potential race condition in amdtee_close_session that may
cause use-after-free in amdtee_open_session. For instance, if a session
has refcount == 1, and one thread tries to free this session via:
kref_put(&sess->refcount, destroy_session);
the reference count will get decremented, and the next step would be to
call destroy_session(). However, if in another thread,
amdtee_open_session() is called before destroy_session() has completed
execution, alloc_session() may return 'sess' that will be freed up
later in destroy_session() leading to use-after-free in
amdtee_open_session.
To fix this issue, treat decrement of sess->refcount and removal of
'sess' from session list in destroy_session() as a critical section, so
that it is executed atomically.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
tee: amdtee: fix use-after-free vulnerability in amdtee_close_session
There is a potential race condition in amdtee_close_session that may
cause use-after-free in amdtee_open_session. For instance, if a session
has refcount == 1, and one thread tries to free this session via:
kref_put(&sess->refcount, destroy_session);
the reference count will get decremented, and the next step would be to
call destroy_session(). However, if in another thread,
amdtee_open_session() is called before destroy_session() has completed
execution, alloc_session() may return 'sess' that will be freed up
later in destroy_session() leading to use-after-free in
amdtee_open_session.
To fix this issue, treat decrement of sess->refcount and removal of
'sess' from session list in destroy_session() as a critical section, so
that it is executed atomically.
🎖@cveNotify
🚨 CVE-2023-52509
In the Linux kernel, the following vulnerability has been resolved:
ravb: Fix use-after-free issue in ravb_tx_timeout_work()
The ravb_stop() should call cancel_work_sync(). Otherwise,
ravb_tx_timeout_work() is possible to use the freed priv after
ravb_remove() was called like below:
CPU0 CPU1
ravb_tx_timeout()
ravb_remove()
unregister_netdev()
free_netdev(ndev)
// free priv
ravb_tx_timeout_work()
// use priv
unregister_netdev() will call .ndo_stop() so that ravb_stop() is
called. And, after phy_stop() is called, netif_carrier_off()
is also called. So that .ndo_tx_timeout() will not be called
after phy_stop().
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
ravb: Fix use-after-free issue in ravb_tx_timeout_work()
The ravb_stop() should call cancel_work_sync(). Otherwise,
ravb_tx_timeout_work() is possible to use the freed priv after
ravb_remove() was called like below:
CPU0 CPU1
ravb_tx_timeout()
ravb_remove()
unregister_netdev()
free_netdev(ndev)
// free priv
ravb_tx_timeout_work()
// use priv
unregister_netdev() will call .ndo_stop() so that ravb_stop() is
called. And, after phy_stop() is called, netif_carrier_off()
is also called. So that .ndo_tx_timeout() will not be called
after phy_stop().
🎖@cveNotify
🚨 CVE-2023-52513
In the Linux kernel, the following vulnerability has been resolved:
RDMA/siw: Fix connection failure handling
In case immediate MPA request processing fails, the newly
created endpoint unlinks the listening endpoint and is
ready to be dropped. This special case was not handled
correctly by the code handling the later TCP socket close,
causing a NULL dereference crash in siw_cm_work_handler()
when dereferencing a NULL listener. We now also cancel
the useless MPA timeout, if immediate MPA request
processing fails.
This patch furthermore simplifies MPA processing in general:
Scheduling a useless TCP socket read in sk_data_ready() upcall
is now surpressed, if the socket is already moved out of
TCP_ESTABLISHED state.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
RDMA/siw: Fix connection failure handling
In case immediate MPA request processing fails, the newly
created endpoint unlinks the listening endpoint and is
ready to be dropped. This special case was not handled
correctly by the code handling the later TCP socket close,
causing a NULL dereference crash in siw_cm_work_handler()
when dereferencing a NULL listener. We now also cancel
the useless MPA timeout, if immediate MPA request
processing fails.
This patch furthermore simplifies MPA processing in general:
Scheduling a useless TCP socket read in sk_data_ready() upcall
is now surpressed, if the socket is already moved out of
TCP_ESTABLISHED state.
🎖@cveNotify
🚨 CVE-2023-52515
In the Linux kernel, the following vulnerability has been resolved:
RDMA/srp: Do not call scsi_done() from srp_abort()
After scmd_eh_abort_handler() has called the SCSI LLD eh_abort_handler
callback, it performs one of the following actions:
* Call scsi_queue_insert().
* Call scsi_finish_command().
* Call scsi_eh_scmd_add().
Hence, SCSI abort handlers must not call scsi_done(). Otherwise all
the above actions would trigger a use-after-free. Hence remove the
scsi_done() call from srp_abort(). Keep the srp_free_req() call
before returning SUCCESS because we may not see the command again if
SUCCESS is returned.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
RDMA/srp: Do not call scsi_done() from srp_abort()
After scmd_eh_abort_handler() has called the SCSI LLD eh_abort_handler
callback, it performs one of the following actions:
* Call scsi_queue_insert().
* Call scsi_finish_command().
* Call scsi_eh_scmd_add().
Hence, SCSI abort handlers must not call scsi_done(). Otherwise all
the above actions would trigger a use-after-free. Hence remove the
scsi_done() call from srp_abort(). Keep the srp_free_req() call
before returning SUCCESS because we may not see the command again if
SUCCESS is returned.
🎖@cveNotify
🚨 CVE-2023-52517
In the Linux kernel, the following vulnerability has been resolved:
spi: sun6i: fix race between DMA RX transfer completion and RX FIFO drain
Previously the transfer complete IRQ immediately drained to RX FIFO to
read any data remaining in FIFO to the RX buffer. This behaviour is
correct when dealing with SPI in interrupt mode. However in DMA mode the
transfer complete interrupt still fires as soon as all bytes to be
transferred have been stored in the FIFO. At that point data in the FIFO
still needs to be picked up by the DMA engine. Thus the drain procedure
and DMA engine end up racing to read from RX FIFO, corrupting any data
read. Additionally the RX buffer pointer is never adjusted according to
DMA progress in DMA mode, thus calling the RX FIFO drain procedure in DMA
mode is a bug.
Fix corruptions in DMA RX mode by draining RX FIFO only in interrupt mode.
Also wait for completion of RX DMA when in DMA mode before returning to
ensure all data has been copied to the supplied memory buffer.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
spi: sun6i: fix race between DMA RX transfer completion and RX FIFO drain
Previously the transfer complete IRQ immediately drained to RX FIFO to
read any data remaining in FIFO to the RX buffer. This behaviour is
correct when dealing with SPI in interrupt mode. However in DMA mode the
transfer complete interrupt still fires as soon as all bytes to be
transferred have been stored in the FIFO. At that point data in the FIFO
still needs to be picked up by the DMA engine. Thus the drain procedure
and DMA engine end up racing to read from RX FIFO, corrupting any data
read. Additionally the RX buffer pointer is never adjusted according to
DMA progress in DMA mode, thus calling the RX FIFO drain procedure in DMA
mode is a bug.
Fix corruptions in DMA RX mode by draining RX FIFO only in interrupt mode.
Also wait for completion of RX DMA when in DMA mode before returning to
ensure all data has been copied to the supplied memory buffer.
🎖@cveNotify
🚨 CVE-2023-52522
In the Linux kernel, the following vulnerability has been resolved:
net: fix possible store tearing in neigh_periodic_work()
While looking at a related syzbot report involving neigh_periodic_work(),
I found that I forgot to add an annotation when deleting an
RCU protected item from a list.
Readers use rcu_deference(*np), we need to use either
rcu_assign_pointer() or WRITE_ONCE() on writer side
to prevent store tearing.
I use rcu_assign_pointer() to have lockdep support,
this was the choice made in neigh_flush_dev().
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
net: fix possible store tearing in neigh_periodic_work()
While looking at a related syzbot report involving neigh_periodic_work(),
I found that I forgot to add an annotation when deleting an
RCU protected item from a list.
Readers use rcu_deference(*np), we need to use either
rcu_assign_pointer() or WRITE_ONCE() on writer side
to prevent store tearing.
I use rcu_assign_pointer() to have lockdep support,
this was the choice made in neigh_flush_dev().
🎖@cveNotify
🚨 CVE-2023-52523
In the Linux kernel, the following vulnerability has been resolved:
bpf, sockmap: Reject sk_msg egress redirects to non-TCP sockets
With a SOCKMAP/SOCKHASH map and an sk_msg program user can steer messages
sent from one TCP socket (s1) to actually egress from another TCP
socket (s2):
tcp_bpf_sendmsg(s1) // = sk_prot->sendmsg
tcp_bpf_send_verdict(s1) // __SK_REDIRECT case
tcp_bpf_sendmsg_redir(s2)
tcp_bpf_push_locked(s2)
tcp_bpf_push(s2)
tcp_rate_check_app_limited(s2) // expects tcp_sock
tcp_sendmsg_locked(s2) // ditto
There is a hard-coded assumption in the call-chain, that the egress
socket (s2) is a TCP socket.
However in commit 122e6c79efe1 ("sock_map: Update sock type checks for
UDP") we have enabled redirects to non-TCP sockets. This was done for the
sake of BPF sk_skb programs. There was no indention to support sk_msg
send-to-egress use case.
As a result, attempts to send-to-egress through a non-TCP socket lead to a
crash due to invalid downcast from sock to tcp_sock:
BUG: kernel NULL pointer dereference, address: 000000000000002f
...
Call Trace:
<TASK>
? show_regs+0x60/0x70
? __die+0x1f/0x70
? page_fault_oops+0x80/0x160
? do_user_addr_fault+0x2d7/0x800
? rcu_is_watching+0x11/0x50
? exc_page_fault+0x70/0x1c0
? asm_exc_page_fault+0x27/0x30
? tcp_tso_segs+0x14/0xa0
tcp_write_xmit+0x67/0xce0
__tcp_push_pending_frames+0x32/0xf0
tcp_push+0x107/0x140
tcp_sendmsg_locked+0x99f/0xbb0
tcp_bpf_push+0x19d/0x3a0
tcp_bpf_sendmsg_redir+0x55/0xd0
tcp_bpf_send_verdict+0x407/0x550
tcp_bpf_sendmsg+0x1a1/0x390
inet_sendmsg+0x6a/0x70
sock_sendmsg+0x9d/0xc0
? sockfd_lookup_light+0x12/0x80
__sys_sendto+0x10e/0x160
? syscall_enter_from_user_mode+0x20/0x60
? __this_cpu_preempt_check+0x13/0x20
? lockdep_hardirqs_on+0x82/0x110
__x64_sys_sendto+0x1f/0x30
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Reject selecting a non-TCP sockets as redirect target from a BPF sk_msg
program to prevent the crash. When attempted, user will receive an EACCES
error from send/sendto/sendmsg() syscall.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
bpf, sockmap: Reject sk_msg egress redirects to non-TCP sockets
With a SOCKMAP/SOCKHASH map and an sk_msg program user can steer messages
sent from one TCP socket (s1) to actually egress from another TCP
socket (s2):
tcp_bpf_sendmsg(s1) // = sk_prot->sendmsg
tcp_bpf_send_verdict(s1) // __SK_REDIRECT case
tcp_bpf_sendmsg_redir(s2)
tcp_bpf_push_locked(s2)
tcp_bpf_push(s2)
tcp_rate_check_app_limited(s2) // expects tcp_sock
tcp_sendmsg_locked(s2) // ditto
There is a hard-coded assumption in the call-chain, that the egress
socket (s2) is a TCP socket.
However in commit 122e6c79efe1 ("sock_map: Update sock type checks for
UDP") we have enabled redirects to non-TCP sockets. This was done for the
sake of BPF sk_skb programs. There was no indention to support sk_msg
send-to-egress use case.
As a result, attempts to send-to-egress through a non-TCP socket lead to a
crash due to invalid downcast from sock to tcp_sock:
BUG: kernel NULL pointer dereference, address: 000000000000002f
...
Call Trace:
<TASK>
? show_regs+0x60/0x70
? __die+0x1f/0x70
? page_fault_oops+0x80/0x160
? do_user_addr_fault+0x2d7/0x800
? rcu_is_watching+0x11/0x50
? exc_page_fault+0x70/0x1c0
? asm_exc_page_fault+0x27/0x30
? tcp_tso_segs+0x14/0xa0
tcp_write_xmit+0x67/0xce0
__tcp_push_pending_frames+0x32/0xf0
tcp_push+0x107/0x140
tcp_sendmsg_locked+0x99f/0xbb0
tcp_bpf_push+0x19d/0x3a0
tcp_bpf_sendmsg_redir+0x55/0xd0
tcp_bpf_send_verdict+0x407/0x550
tcp_bpf_sendmsg+0x1a1/0x390
inet_sendmsg+0x6a/0x70
sock_sendmsg+0x9d/0xc0
? sockfd_lookup_light+0x12/0x80
__sys_sendto+0x10e/0x160
? syscall_enter_from_user_mode+0x20/0x60
? __this_cpu_preempt_check+0x13/0x20
? lockdep_hardirqs_on+0x82/0x110
__x64_sys_sendto+0x1f/0x30
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Reject selecting a non-TCP sockets as redirect target from a BPF sk_msg
program to prevent the crash. When attempted, user will receive an EACCES
error from send/sendto/sendmsg() syscall.
🎖@cveNotify
🚨 CVE-2023-52530
In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix potential key use-after-free
When ieee80211_key_link() is called by ieee80211_gtk_rekey_add()
but returns 0 due to KRACK protection (identical key reinstall),
ieee80211_gtk_rekey_add() will still return a pointer into the
key, in a potential use-after-free. This normally doesn't happen
since it's only called by iwlwifi in case of WoWLAN rekey offload
which has its own KRACK protection, but still better to fix, do
that by returning an error code and converting that to success on
the cfg80211 boundary only, leaving the error for bad callers of
ieee80211_gtk_rekey_add().
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix potential key use-after-free
When ieee80211_key_link() is called by ieee80211_gtk_rekey_add()
but returns 0 due to KRACK protection (identical key reinstall),
ieee80211_gtk_rekey_add() will still return a pointer into the
key, in a potential use-after-free. This normally doesn't happen
since it's only called by iwlwifi in case of WoWLAN rekey offload
which has its own KRACK protection, but still better to fix, do
that by returning an error code and converting that to success on
the cfg80211 boundary only, leaving the error for bad callers of
ieee80211_gtk_rekey_add().
🎖@cveNotify
🚨 CVE-2023-52572
In the Linux kernel, the following vulnerability has been resolved:
cifs: Fix UAF in cifs_demultiplex_thread()
There is a UAF when xfstests on cifs:
BUG: KASAN: use-after-free in smb2_is_network_name_deleted+0x27/0x160
Read of size 4 at addr ffff88810103fc08 by task cifsd/923
CPU: 1 PID: 923 Comm: cifsd Not tainted 6.1.0-rc4+ #45
...
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x44
print_report+0x171/0x472
kasan_report+0xad/0x130
kasan_check_range+0x145/0x1a0
smb2_is_network_name_deleted+0x27/0x160
cifs_demultiplex_thread.cold+0x172/0x5a4
kthread+0x165/0x1a0
ret_from_fork+0x1f/0x30
</TASK>
Allocated by task 923:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
__kasan_slab_alloc+0x54/0x60
kmem_cache_alloc+0x147/0x320
mempool_alloc+0xe1/0x260
cifs_small_buf_get+0x24/0x60
allocate_buffers+0xa1/0x1c0
cifs_demultiplex_thread+0x199/0x10d0
kthread+0x165/0x1a0
ret_from_fork+0x1f/0x30
Freed by task 921:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x40
____kasan_slab_free+0x143/0x1b0
kmem_cache_free+0xe3/0x4d0
cifs_small_buf_release+0x29/0x90
SMB2_negotiate+0x8b7/0x1c60
smb2_negotiate+0x51/0x70
cifs_negotiate_protocol+0xf0/0x160
cifs_get_smb_ses+0x5fa/0x13c0
mount_get_conns+0x7a/0x750
cifs_mount+0x103/0xd00
cifs_smb3_do_mount+0x1dd/0xcb0
smb3_get_tree+0x1d5/0x300
vfs_get_tree+0x41/0xf0
path_mount+0x9b3/0xdd0
__x64_sys_mount+0x190/0x1d0
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
The UAF is because:
mount(pid: 921) | cifsd(pid: 923)
-------------------------------|-------------------------------
| cifs_demultiplex_thread
SMB2_negotiate |
cifs_send_recv |
compound_send_recv |
smb_send_rqst |
wait_for_response |
wait_event_state [1] |
| standard_receive3
| cifs_handle_standard
| handle_mid
| mid->resp_buf = buf; [2]
| dequeue_mid [3]
KILL the process [4] |
resp_iov[i].iov_base = buf |
free_rsp_buf [5] |
| is_network_name_deleted [6]
| callback
1. After send request to server, wait the response until
mid->mid_state != SUBMITTED;
2. Receive response from server, and set it to mid;
3. Set the mid state to RECEIVED;
4. Kill the process, the mid state already RECEIVED, get 0;
5. Handle and release the negotiate response;
6. UAF.
It can be easily reproduce with add some delay in [3] - [6].
Only sync call has the problem since async call's callback is
executed in cifsd process.
Add an extra state to mark the mid state to READY before wakeup the
waitter, then it can get the resp safely.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
cifs: Fix UAF in cifs_demultiplex_thread()
There is a UAF when xfstests on cifs:
BUG: KASAN: use-after-free in smb2_is_network_name_deleted+0x27/0x160
Read of size 4 at addr ffff88810103fc08 by task cifsd/923
CPU: 1 PID: 923 Comm: cifsd Not tainted 6.1.0-rc4+ #45
...
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x44
print_report+0x171/0x472
kasan_report+0xad/0x130
kasan_check_range+0x145/0x1a0
smb2_is_network_name_deleted+0x27/0x160
cifs_demultiplex_thread.cold+0x172/0x5a4
kthread+0x165/0x1a0
ret_from_fork+0x1f/0x30
</TASK>
Allocated by task 923:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
__kasan_slab_alloc+0x54/0x60
kmem_cache_alloc+0x147/0x320
mempool_alloc+0xe1/0x260
cifs_small_buf_get+0x24/0x60
allocate_buffers+0xa1/0x1c0
cifs_demultiplex_thread+0x199/0x10d0
kthread+0x165/0x1a0
ret_from_fork+0x1f/0x30
Freed by task 921:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x40
____kasan_slab_free+0x143/0x1b0
kmem_cache_free+0xe3/0x4d0
cifs_small_buf_release+0x29/0x90
SMB2_negotiate+0x8b7/0x1c60
smb2_negotiate+0x51/0x70
cifs_negotiate_protocol+0xf0/0x160
cifs_get_smb_ses+0x5fa/0x13c0
mount_get_conns+0x7a/0x750
cifs_mount+0x103/0xd00
cifs_smb3_do_mount+0x1dd/0xcb0
smb3_get_tree+0x1d5/0x300
vfs_get_tree+0x41/0xf0
path_mount+0x9b3/0xdd0
__x64_sys_mount+0x190/0x1d0
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
The UAF is because:
mount(pid: 921) | cifsd(pid: 923)
-------------------------------|-------------------------------
| cifs_demultiplex_thread
SMB2_negotiate |
cifs_send_recv |
compound_send_recv |
smb_send_rqst |
wait_for_response |
wait_event_state [1] |
| standard_receive3
| cifs_handle_standard
| handle_mid
| mid->resp_buf = buf; [2]
| dequeue_mid [3]
KILL the process [4] |
resp_iov[i].iov_base = buf |
free_rsp_buf [5] |
| is_network_name_deleted [6]
| callback
1. After send request to server, wait the response until
mid->mid_state != SUBMITTED;
2. Receive response from server, and set it to mid;
3. Set the mid state to RECEIVED;
4. Kill the process, the mid state already RECEIVED, get 0;
5. Handle and release the negotiate response;
6. UAF.
It can be easily reproduce with add some delay in [3] - [6].
Only sync call has the problem since async call's callback is
executed in cifsd process.
Add an extra state to mark the mid state to READY before wakeup the
waitter, then it can get the resp safely.
🎖@cveNotify
🚨 CVE-2023-52574
In the Linux kernel, the following vulnerability has been resolved:
team: fix null-ptr-deref when team device type is changed
Get a null-ptr-deref bug as follows with reproducer [1].
BUG: kernel NULL pointer dereference, address: 0000000000000228
...
RIP: 0010:vlan_dev_hard_header+0x35/0x140 [8021q]
...
Call Trace:
<TASK>
? __die+0x24/0x70
? page_fault_oops+0x82/0x150
? exc_page_fault+0x69/0x150
? asm_exc_page_fault+0x26/0x30
? vlan_dev_hard_header+0x35/0x140 [8021q]
? vlan_dev_hard_header+0x8e/0x140 [8021q]
neigh_connected_output+0xb2/0x100
ip6_finish_output2+0x1cb/0x520
? nf_hook_slow+0x43/0xc0
? ip6_mtu+0x46/0x80
ip6_finish_output+0x2a/0xb0
mld_sendpack+0x18f/0x250
mld_ifc_work+0x39/0x160
process_one_work+0x1e6/0x3f0
worker_thread+0x4d/0x2f0
? __pfx_worker_thread+0x10/0x10
kthread+0xe5/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
[1]
$ teamd -t team0 -d -c '{"runner": {"name": "loadbalance"}}'
$ ip link add name t-dummy type dummy
$ ip link add link t-dummy name t-dummy.100 type vlan id 100
$ ip link add name t-nlmon type nlmon
$ ip link set t-nlmon master team0
$ ip link set t-nlmon nomaster
$ ip link set t-dummy up
$ ip link set team0 up
$ ip link set t-dummy.100 down
$ ip link set t-dummy.100 master team0
When enslave a vlan device to team device and team device type is changed
from non-ether to ether, header_ops of team device is changed to
vlan_header_ops. That is incorrect and will trigger null-ptr-deref
for vlan->real_dev in vlan_dev_hard_header() because team device is not
a vlan device.
Cache eth_header_ops in team_setup(), then assign cached header_ops to
header_ops of team net device when its type is changed from non-ether
to ether to fix the bug.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
team: fix null-ptr-deref when team device type is changed
Get a null-ptr-deref bug as follows with reproducer [1].
BUG: kernel NULL pointer dereference, address: 0000000000000228
...
RIP: 0010:vlan_dev_hard_header+0x35/0x140 [8021q]
...
Call Trace:
<TASK>
? __die+0x24/0x70
? page_fault_oops+0x82/0x150
? exc_page_fault+0x69/0x150
? asm_exc_page_fault+0x26/0x30
? vlan_dev_hard_header+0x35/0x140 [8021q]
? vlan_dev_hard_header+0x8e/0x140 [8021q]
neigh_connected_output+0xb2/0x100
ip6_finish_output2+0x1cb/0x520
? nf_hook_slow+0x43/0xc0
? ip6_mtu+0x46/0x80
ip6_finish_output+0x2a/0xb0
mld_sendpack+0x18f/0x250
mld_ifc_work+0x39/0x160
process_one_work+0x1e6/0x3f0
worker_thread+0x4d/0x2f0
? __pfx_worker_thread+0x10/0x10
kthread+0xe5/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
[1]
$ teamd -t team0 -d -c '{"runner": {"name": "loadbalance"}}'
$ ip link add name t-dummy type dummy
$ ip link add link t-dummy name t-dummy.100 type vlan id 100
$ ip link add name t-nlmon type nlmon
$ ip link set t-nlmon master team0
$ ip link set t-nlmon nomaster
$ ip link set t-dummy up
$ ip link set team0 up
$ ip link set t-dummy.100 down
$ ip link set t-dummy.100 master team0
When enslave a vlan device to team device and team device type is changed
from non-ether to ether, header_ops of team device is changed to
vlan_header_ops. That is incorrect and will trigger null-ptr-deref
for vlan->real_dev in vlan_dev_hard_header() because team device is not
a vlan device.
Cache eth_header_ops in team_setup(), then assign cached header_ops to
header_ops of team net device when its type is changed from non-ether
to ether to fix the bug.
🎖@cveNotify
🚨 CVE-2021-47082
In the Linux kernel, the following vulnerability has been resolved:
tun: avoid double free in tun_free_netdev
Avoid double free in tun_free_netdev() by moving the
dev->tstats and tun->security allocs to a new ndo_init routine
(tun_net_init()) that will be called by register_netdevice().
ndo_init is paired with the desctructor (tun_free_netdev()),
so if there's an error in register_netdevice() the destructor
will handle the frees.
BUG: KASAN: double-free or invalid-free in selinux_tun_dev_free_security+0x1a/0x20 security/selinux/hooks.c:5605
CPU: 0 PID: 25750 Comm: syz-executor416 Not tainted 5.16.0-rc2-syzk #1
Hardware name: Red Hat KVM, BIOS
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x89/0xb5 lib/dump_stack.c:106
print_address_description.constprop.9+0x28/0x160 mm/kasan/report.c:247
kasan_report_invalid_free+0x55/0x80 mm/kasan/report.c:372
____kasan_slab_free mm/kasan/common.c:346 [inline]
__kasan_slab_free+0x107/0x120 mm/kasan/common.c:374
kasan_slab_free include/linux/kasan.h:235 [inline]
slab_free_hook mm/slub.c:1723 [inline]
slab_free_freelist_hook mm/slub.c:1749 [inline]
slab_free mm/slub.c:3513 [inline]
kfree+0xac/0x2d0 mm/slub.c:4561
selinux_tun_dev_free_security+0x1a/0x20 security/selinux/hooks.c:5605
security_tun_dev_free_security+0x4f/0x90 security/security.c:2342
tun_free_netdev+0xe6/0x150 drivers/net/tun.c:2215
netdev_run_todo+0x4df/0x840 net/core/dev.c:10627
rtnl_unlock+0x13/0x20 net/core/rtnetlink.c:112
__tun_chr_ioctl+0x80c/0x2870 drivers/net/tun.c:3302
tun_chr_ioctl+0x2f/0x40 drivers/net/tun.c:3311
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:874 [inline]
__se_sys_ioctl fs/ioctl.c:860 [inline]
__x64_sys_ioctl+0x19d/0x220 fs/ioctl.c:860
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3a/0x80 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
tun: avoid double free in tun_free_netdev
Avoid double free in tun_free_netdev() by moving the
dev->tstats and tun->security allocs to a new ndo_init routine
(tun_net_init()) that will be called by register_netdevice().
ndo_init is paired with the desctructor (tun_free_netdev()),
so if there's an error in register_netdevice() the destructor
will handle the frees.
BUG: KASAN: double-free or invalid-free in selinux_tun_dev_free_security+0x1a/0x20 security/selinux/hooks.c:5605
CPU: 0 PID: 25750 Comm: syz-executor416 Not tainted 5.16.0-rc2-syzk #1
Hardware name: Red Hat KVM, BIOS
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x89/0xb5 lib/dump_stack.c:106
print_address_description.constprop.9+0x28/0x160 mm/kasan/report.c:247
kasan_report_invalid_free+0x55/0x80 mm/kasan/report.c:372
____kasan_slab_free mm/kasan/common.c:346 [inline]
__kasan_slab_free+0x107/0x120 mm/kasan/common.c:374
kasan_slab_free include/linux/kasan.h:235 [inline]
slab_free_hook mm/slub.c:1723 [inline]
slab_free_freelist_hook mm/slub.c:1749 [inline]
slab_free mm/slub.c:3513 [inline]
kfree+0xac/0x2d0 mm/slub.c:4561
selinux_tun_dev_free_security+0x1a/0x20 security/selinux/hooks.c:5605
security_tun_dev_free_security+0x4f/0x90 security/security.c:2342
tun_free_netdev+0xe6/0x150 drivers/net/tun.c:2215
netdev_run_todo+0x4df/0x840 net/core/dev.c:10627
rtnl_unlock+0x13/0x20 net/core/rtnetlink.c:112
__tun_chr_ioctl+0x80c/0x2870 drivers/net/tun.c:3302
tun_chr_ioctl+0x2f/0x40 drivers/net/tun.c:3311
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:874 [inline]
__se_sys_ioctl fs/ioctl.c:860 [inline]
__x64_sys_ioctl+0x19d/0x220 fs/ioctl.c:860
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3a/0x80 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
🎖@cveNotify
🚨 CVE-2021-47083
In the Linux kernel, the following vulnerability has been resolved:
pinctrl: mediatek: fix global-out-of-bounds issue
When eint virtual eint number is greater than gpio number,
it maybe produce 'desc[eint_n]' size globle-out-of-bounds issue.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
pinctrl: mediatek: fix global-out-of-bounds issue
When eint virtual eint number is greater than gpio number,
it maybe produce 'desc[eint_n]' size globle-out-of-bounds issue.
🎖@cveNotify
🚨 CVE-2021-47087
In the Linux kernel, the following vulnerability has been resolved:
tee: optee: Fix incorrect page free bug
Pointer to the allocated pages (struct page *page) has already
progressed towards the end of allocation. It is incorrect to perform
__free_pages(page, order) using this pointer as we would free any
arbitrary pages. Fix this by stop modifying the page pointer.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
tee: optee: Fix incorrect page free bug
Pointer to the allocated pages (struct page *page) has already
progressed towards the end of allocation. It is incorrect to perform
__free_pages(page, order) using this pointer as we would free any
arbitrary pages. Fix this by stop modifying the page pointer.
🎖@cveNotify
🚨 CVE-2021-47094
In the Linux kernel, the following vulnerability has been resolved:
KVM: x86/mmu: Don't advance iterator after restart due to yielding
After dropping mmu_lock in the TDP MMU, restart the iterator during
tdp_iter_next() and do not advance the iterator. Advancing the iterator
results in skipping the top-level SPTE and all its children, which is
fatal if any of the skipped SPTEs were not visited before yielding.
When zapping all SPTEs, i.e. when min_level == root_level, restarting the
iter and then invoking tdp_iter_next() is always fatal if the current gfn
has as a valid SPTE, as advancing the iterator results in try_step_side()
skipping the current gfn, which wasn't visited before yielding.
Sprinkle WARNs on iter->yielded being true in various helpers that are
often used in conjunction with yielding, and tag the helper with
__must_check to reduce the probabily of improper usage.
Failing to zap a top-level SPTE manifests in one of two ways. If a valid
SPTE is skipped by both kvm_tdp_mmu_zap_all() and kvm_tdp_mmu_put_root(),
the shadow page will be leaked and KVM will WARN accordingly.
WARNING: CPU: 1 PID: 3509 at arch/x86/kvm/mmu/tdp_mmu.c:46 [kvm]
RIP: 0010:kvm_mmu_uninit_tdp_mmu+0x3e/0x50 [kvm]
Call Trace:
<TASK>
kvm_arch_destroy_vm+0x130/0x1b0 [kvm]
kvm_destroy_vm+0x162/0x2a0 [kvm]
kvm_vcpu_release+0x34/0x60 [kvm]
__fput+0x82/0x240
task_work_run+0x5c/0x90
do_exit+0x364/0xa10
? futex_unqueue+0x38/0x60
do_group_exit+0x33/0xa0
get_signal+0x155/0x850
arch_do_signal_or_restart+0xed/0x750
exit_to_user_mode_prepare+0xc5/0x120
syscall_exit_to_user_mode+0x1d/0x40
do_syscall_64+0x48/0xc0
entry_SYSCALL_64_after_hwframe+0x44/0xae
If kvm_tdp_mmu_zap_all() skips a gfn/SPTE but that SPTE is then zapped by
kvm_tdp_mmu_put_root(), KVM triggers a use-after-free in the form of
marking a struct page as dirty/accessed after it has been put back on the
free list. This directly triggers a WARN due to encountering a page with
page_count() == 0, but it can also lead to data corruption and additional
errors in the kernel.
WARNING: CPU: 7 PID: 1995658 at arch/x86/kvm/../../../virt/kvm/kvm_main.c:171
RIP: 0010:kvm_is_zone_device_pfn.part.0+0x9e/0xd0 [kvm]
Call Trace:
<TASK>
kvm_set_pfn_dirty+0x120/0x1d0 [kvm]
__handle_changed_spte+0x92e/0xca0 [kvm]
__handle_changed_spte+0x63c/0xca0 [kvm]
__handle_changed_spte+0x63c/0xca0 [kvm]
__handle_changed_spte+0x63c/0xca0 [kvm]
zap_gfn_range+0x549/0x620 [kvm]
kvm_tdp_mmu_put_root+0x1b6/0x270 [kvm]
mmu_free_root_page+0x219/0x2c0 [kvm]
kvm_mmu_free_roots+0x1b4/0x4e0 [kvm]
kvm_mmu_unload+0x1c/0xa0 [kvm]
kvm_arch_destroy_vm+0x1f2/0x5c0 [kvm]
kvm_put_kvm+0x3b1/0x8b0 [kvm]
kvm_vcpu_release+0x4e/0x70 [kvm]
__fput+0x1f7/0x8c0
task_work_run+0xf8/0x1a0
do_exit+0x97b/0x2230
do_group_exit+0xda/0x2a0
get_signal+0x3be/0x1e50
arch_do_signal_or_restart+0x244/0x17f0
exit_to_user_mode_prepare+0xcb/0x120
syscall_exit_to_user_mode+0x1d/0x40
do_syscall_64+0x4d/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Note, the underlying bug existed even before commit 1af4a96025b3 ("KVM:
x86/mmu: Yield in TDU MMU iter even if no SPTES changed") moved calls to
tdp_mmu_iter_cond_resched() to the beginning of loops, as KVM could still
incorrectly advance past a top-level entry when yielding on a lower-level
entry. But with respect to leaking shadow pages, the bug was introduced
by yielding before processing the current gfn.
Alternatively, tdp_mmu_iter_cond_resched() could simply fall through, or
callers could jump to their "retry" label. The downside of that approach
is that tdp_mmu_iter_cond_resched() _must_ be called before anything else
in the loop, and there's no easy way to enfornce that requirement.
Ideally, KVM would handling the cond_resched() fully within the iterator
macro (the code is actually quite clean) and avoid this entire class of
bugs, but that is extremely difficult do wh
---truncated---
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
KVM: x86/mmu: Don't advance iterator after restart due to yielding
After dropping mmu_lock in the TDP MMU, restart the iterator during
tdp_iter_next() and do not advance the iterator. Advancing the iterator
results in skipping the top-level SPTE and all its children, which is
fatal if any of the skipped SPTEs were not visited before yielding.
When zapping all SPTEs, i.e. when min_level == root_level, restarting the
iter and then invoking tdp_iter_next() is always fatal if the current gfn
has as a valid SPTE, as advancing the iterator results in try_step_side()
skipping the current gfn, which wasn't visited before yielding.
Sprinkle WARNs on iter->yielded being true in various helpers that are
often used in conjunction with yielding, and tag the helper with
__must_check to reduce the probabily of improper usage.
Failing to zap a top-level SPTE manifests in one of two ways. If a valid
SPTE is skipped by both kvm_tdp_mmu_zap_all() and kvm_tdp_mmu_put_root(),
the shadow page will be leaked and KVM will WARN accordingly.
WARNING: CPU: 1 PID: 3509 at arch/x86/kvm/mmu/tdp_mmu.c:46 [kvm]
RIP: 0010:kvm_mmu_uninit_tdp_mmu+0x3e/0x50 [kvm]
Call Trace:
<TASK>
kvm_arch_destroy_vm+0x130/0x1b0 [kvm]
kvm_destroy_vm+0x162/0x2a0 [kvm]
kvm_vcpu_release+0x34/0x60 [kvm]
__fput+0x82/0x240
task_work_run+0x5c/0x90
do_exit+0x364/0xa10
? futex_unqueue+0x38/0x60
do_group_exit+0x33/0xa0
get_signal+0x155/0x850
arch_do_signal_or_restart+0xed/0x750
exit_to_user_mode_prepare+0xc5/0x120
syscall_exit_to_user_mode+0x1d/0x40
do_syscall_64+0x48/0xc0
entry_SYSCALL_64_after_hwframe+0x44/0xae
If kvm_tdp_mmu_zap_all() skips a gfn/SPTE but that SPTE is then zapped by
kvm_tdp_mmu_put_root(), KVM triggers a use-after-free in the form of
marking a struct page as dirty/accessed after it has been put back on the
free list. This directly triggers a WARN due to encountering a page with
page_count() == 0, but it can also lead to data corruption and additional
errors in the kernel.
WARNING: CPU: 7 PID: 1995658 at arch/x86/kvm/../../../virt/kvm/kvm_main.c:171
RIP: 0010:kvm_is_zone_device_pfn.part.0+0x9e/0xd0 [kvm]
Call Trace:
<TASK>
kvm_set_pfn_dirty+0x120/0x1d0 [kvm]
__handle_changed_spte+0x92e/0xca0 [kvm]
__handle_changed_spte+0x63c/0xca0 [kvm]
__handle_changed_spte+0x63c/0xca0 [kvm]
__handle_changed_spte+0x63c/0xca0 [kvm]
zap_gfn_range+0x549/0x620 [kvm]
kvm_tdp_mmu_put_root+0x1b6/0x270 [kvm]
mmu_free_root_page+0x219/0x2c0 [kvm]
kvm_mmu_free_roots+0x1b4/0x4e0 [kvm]
kvm_mmu_unload+0x1c/0xa0 [kvm]
kvm_arch_destroy_vm+0x1f2/0x5c0 [kvm]
kvm_put_kvm+0x3b1/0x8b0 [kvm]
kvm_vcpu_release+0x4e/0x70 [kvm]
__fput+0x1f7/0x8c0
task_work_run+0xf8/0x1a0
do_exit+0x97b/0x2230
do_group_exit+0xda/0x2a0
get_signal+0x3be/0x1e50
arch_do_signal_or_restart+0x244/0x17f0
exit_to_user_mode_prepare+0xcb/0x120
syscall_exit_to_user_mode+0x1d/0x40
do_syscall_64+0x4d/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Note, the underlying bug existed even before commit 1af4a96025b3 ("KVM:
x86/mmu: Yield in TDU MMU iter even if no SPTES changed") moved calls to
tdp_mmu_iter_cond_resched() to the beginning of loops, as KVM could still
incorrectly advance past a top-level entry when yielding on a lower-level
entry. But with respect to leaking shadow pages, the bug was introduced
by yielding before processing the current gfn.
Alternatively, tdp_mmu_iter_cond_resched() could simply fall through, or
callers could jump to their "retry" label. The downside of that approach
is that tdp_mmu_iter_cond_resched() _must_ be called before anything else
in the loop, and there's no easy way to enfornce that requirement.
Ideally, KVM would handling the cond_resched() fully within the iterator
macro (the code is actually quite clean) and avoid this entire class of
bugs, but that is extremely difficult do wh
---truncated---
🎖@cveNotify
🚨 CVE-2021-47099
In the Linux kernel, the following vulnerability has been resolved:
veth: ensure skb entering GRO are not cloned.
After commit d3256efd8e8b ("veth: allow enabling NAPI even without XDP"),
if GRO is enabled on a veth device and TSO is disabled on the peer
device, TCP skbs will go through the NAPI callback. If there is no XDP
program attached, the veth code does not perform any share check, and
shared/cloned skbs could enter the GRO engine.
Ignat reported a BUG triggered later-on due to the above condition:
[ 53.970529][ C1] kernel BUG at net/core/skbuff.c:3574!
[ 53.981755][ C1] invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
[ 53.982634][ C1] CPU: 1 PID: 19 Comm: ksoftirqd/1 Not tainted 5.16.0-rc5+ #25
[ 53.982634][ C1] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
[ 53.982634][ C1] RIP: 0010:skb_shift+0x13ef/0x23b0
[ 53.982634][ C1] Code: ea 03 0f b6 04 02 48 89 fa 83 e2 07 38 d0
7f 08 84 c0 0f 85 41 0c 00 00 41 80 7f 02 00 4d 8d b5 d0 00 00 00 0f
85 74 f5 ff ff <0f> 0b 4d 8d 77 20 be 04 00 00 00 4c 89 44 24 78 4c 89
f7 4c 89 8c
[ 53.982634][ C1] RSP: 0018:ffff8881008f7008 EFLAGS: 00010246
[ 53.982634][ C1] RAX: 0000000000000000 RBX: ffff8881180b4c80 RCX: 0000000000000000
[ 53.982634][ C1] RDX: 0000000000000002 RSI: ffff8881180b4d3c RDI: ffff88810bc9cac2
[ 53.982634][ C1] RBP: ffff8881008f70b8 R08: ffff8881180b4cf4 R09: ffff8881180b4cf0
[ 53.982634][ C1] R10: ffffed1022999e5c R11: 0000000000000002 R12: 0000000000000590
[ 53.982634][ C1] R13: ffff88810f940c80 R14: ffff88810f940d50 R15: ffff88810bc9cac0
[ 53.982634][ C1] FS: 0000000000000000(0000) GS:ffff888235880000(0000) knlGS:0000000000000000
[ 53.982634][ C1] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 53.982634][ C1] CR2: 00007ff5f9b86680 CR3: 0000000108ce8004 CR4: 0000000000170ee0
[ 53.982634][ C1] Call Trace:
[ 53.982634][ C1] <TASK>
[ 53.982634][ C1] tcp_sacktag_walk+0xaba/0x18e0
[ 53.982634][ C1] tcp_sacktag_write_queue+0xe7b/0x3460
[ 53.982634][ C1] tcp_ack+0x2666/0x54b0
[ 53.982634][ C1] tcp_rcv_established+0x4d9/0x20f0
[ 53.982634][ C1] tcp_v4_do_rcv+0x551/0x810
[ 53.982634][ C1] tcp_v4_rcv+0x22ed/0x2ed0
[ 53.982634][ C1] ip_protocol_deliver_rcu+0x96/0xaf0
[ 53.982634][ C1] ip_local_deliver_finish+0x1e0/0x2f0
[ 53.982634][ C1] ip_sublist_rcv_finish+0x211/0x440
[ 53.982634][ C1] ip_list_rcv_finish.constprop.0+0x424/0x660
[ 53.982634][ C1] ip_list_rcv+0x2c8/0x410
[ 53.982634][ C1] __netif_receive_skb_list_core+0x65c/0x910
[ 53.982634][ C1] netif_receive_skb_list_internal+0x5f9/0xcb0
[ 53.982634][ C1] napi_complete_done+0x188/0x6e0
[ 53.982634][ C1] gro_cell_poll+0x10c/0x1d0
[ 53.982634][ C1] __napi_poll+0xa1/0x530
[ 53.982634][ C1] net_rx_action+0x567/0x1270
[ 53.982634][ C1] __do_softirq+0x28a/0x9ba
[ 53.982634][ C1] run_ksoftirqd+0x32/0x60
[ 53.982634][ C1] smpboot_thread_fn+0x559/0x8c0
[ 53.982634][ C1] kthread+0x3b9/0x490
[ 53.982634][ C1] ret_from_fork+0x22/0x30
[ 53.982634][ C1] </TASK>
Address the issue by skipping the GRO stage for shared or cloned skbs.
To reduce the chance of OoO, try to unclone the skbs before giving up.
v1 -> v2:
- use avoid skb_copy and fallback to netif_receive_skb - Eric
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
veth: ensure skb entering GRO are not cloned.
After commit d3256efd8e8b ("veth: allow enabling NAPI even without XDP"),
if GRO is enabled on a veth device and TSO is disabled on the peer
device, TCP skbs will go through the NAPI callback. If there is no XDP
program attached, the veth code does not perform any share check, and
shared/cloned skbs could enter the GRO engine.
Ignat reported a BUG triggered later-on due to the above condition:
[ 53.970529][ C1] kernel BUG at net/core/skbuff.c:3574!
[ 53.981755][ C1] invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
[ 53.982634][ C1] CPU: 1 PID: 19 Comm: ksoftirqd/1 Not tainted 5.16.0-rc5+ #25
[ 53.982634][ C1] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
[ 53.982634][ C1] RIP: 0010:skb_shift+0x13ef/0x23b0
[ 53.982634][ C1] Code: ea 03 0f b6 04 02 48 89 fa 83 e2 07 38 d0
7f 08 84 c0 0f 85 41 0c 00 00 41 80 7f 02 00 4d 8d b5 d0 00 00 00 0f
85 74 f5 ff ff <0f> 0b 4d 8d 77 20 be 04 00 00 00 4c 89 44 24 78 4c 89
f7 4c 89 8c
[ 53.982634][ C1] RSP: 0018:ffff8881008f7008 EFLAGS: 00010246
[ 53.982634][ C1] RAX: 0000000000000000 RBX: ffff8881180b4c80 RCX: 0000000000000000
[ 53.982634][ C1] RDX: 0000000000000002 RSI: ffff8881180b4d3c RDI: ffff88810bc9cac2
[ 53.982634][ C1] RBP: ffff8881008f70b8 R08: ffff8881180b4cf4 R09: ffff8881180b4cf0
[ 53.982634][ C1] R10: ffffed1022999e5c R11: 0000000000000002 R12: 0000000000000590
[ 53.982634][ C1] R13: ffff88810f940c80 R14: ffff88810f940d50 R15: ffff88810bc9cac0
[ 53.982634][ C1] FS: 0000000000000000(0000) GS:ffff888235880000(0000) knlGS:0000000000000000
[ 53.982634][ C1] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 53.982634][ C1] CR2: 00007ff5f9b86680 CR3: 0000000108ce8004 CR4: 0000000000170ee0
[ 53.982634][ C1] Call Trace:
[ 53.982634][ C1] <TASK>
[ 53.982634][ C1] tcp_sacktag_walk+0xaba/0x18e0
[ 53.982634][ C1] tcp_sacktag_write_queue+0xe7b/0x3460
[ 53.982634][ C1] tcp_ack+0x2666/0x54b0
[ 53.982634][ C1] tcp_rcv_established+0x4d9/0x20f0
[ 53.982634][ C1] tcp_v4_do_rcv+0x551/0x810
[ 53.982634][ C1] tcp_v4_rcv+0x22ed/0x2ed0
[ 53.982634][ C1] ip_protocol_deliver_rcu+0x96/0xaf0
[ 53.982634][ C1] ip_local_deliver_finish+0x1e0/0x2f0
[ 53.982634][ C1] ip_sublist_rcv_finish+0x211/0x440
[ 53.982634][ C1] ip_list_rcv_finish.constprop.0+0x424/0x660
[ 53.982634][ C1] ip_list_rcv+0x2c8/0x410
[ 53.982634][ C1] __netif_receive_skb_list_core+0x65c/0x910
[ 53.982634][ C1] netif_receive_skb_list_internal+0x5f9/0xcb0
[ 53.982634][ C1] napi_complete_done+0x188/0x6e0
[ 53.982634][ C1] gro_cell_poll+0x10c/0x1d0
[ 53.982634][ C1] __napi_poll+0xa1/0x530
[ 53.982634][ C1] net_rx_action+0x567/0x1270
[ 53.982634][ C1] __do_softirq+0x28a/0x9ba
[ 53.982634][ C1] run_ksoftirqd+0x32/0x60
[ 53.982634][ C1] smpboot_thread_fn+0x559/0x8c0
[ 53.982634][ C1] kthread+0x3b9/0x490
[ 53.982634][ C1] ret_from_fork+0x22/0x30
[ 53.982634][ C1] </TASK>
Address the issue by skipping the GRO stage for shared or cloned skbs.
To reduce the chance of OoO, try to unclone the skbs before giving up.
v1 -> v2:
- use avoid skb_copy and fallback to netif_receive_skb - Eric
🎖@cveNotify
🚨 CVE-2021-47102
In the Linux kernel, the following vulnerability has been resolved:
net: marvell: prestera: fix incorrect structure access
In line:
upper = info->upper_dev;
We access upper_dev field, which is related only for particular events
(e.g. event == NETDEV_CHANGEUPPER). So, this line cause invalid memory
access for another events,
when ptr is not netdev_notifier_changeupper_info.
The KASAN logs are as follows:
[ 30.123165] BUG: KASAN: stack-out-of-bounds in prestera_netdev_port_event.constprop.0+0x68/0x538 [prestera]
[ 30.133336] Read of size 8 at addr ffff80000cf772b0 by task udevd/778
[ 30.139866]
[ 30.141398] CPU: 0 PID: 778 Comm: udevd Not tainted 5.16.0-rc3 #6
[ 30.147588] Hardware name: DNI AmazonGo1 A7040 board (DT)
[ 30.153056] Call trace:
[ 30.155547] dump_backtrace+0x0/0x2c0
[ 30.159320] show_stack+0x18/0x30
[ 30.162729] dump_stack_lvl+0x68/0x84
[ 30.166491] print_address_description.constprop.0+0x74/0x2b8
[ 30.172346] kasan_report+0x1e8/0x250
[ 30.176102] __asan_load8+0x98/0xe0
[ 30.179682] prestera_netdev_port_event.constprop.0+0x68/0x538 [prestera]
[ 30.186847] prestera_netdev_event_handler+0x1b4/0x1c0 [prestera]
[ 30.193313] raw_notifier_call_chain+0x74/0xa0
[ 30.197860] call_netdevice_notifiers_info+0x68/0xc0
[ 30.202924] register_netdevice+0x3cc/0x760
[ 30.207190] register_netdev+0x24/0x50
[ 30.211015] prestera_device_register+0x8a0/0xba0 [prestera]
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
net: marvell: prestera: fix incorrect structure access
In line:
upper = info->upper_dev;
We access upper_dev field, which is related only for particular events
(e.g. event == NETDEV_CHANGEUPPER). So, this line cause invalid memory
access for another events,
when ptr is not netdev_notifier_changeupper_info.
The KASAN logs are as follows:
[ 30.123165] BUG: KASAN: stack-out-of-bounds in prestera_netdev_port_event.constprop.0+0x68/0x538 [prestera]
[ 30.133336] Read of size 8 at addr ffff80000cf772b0 by task udevd/778
[ 30.139866]
[ 30.141398] CPU: 0 PID: 778 Comm: udevd Not tainted 5.16.0-rc3 #6
[ 30.147588] Hardware name: DNI AmazonGo1 A7040 board (DT)
[ 30.153056] Call trace:
[ 30.155547] dump_backtrace+0x0/0x2c0
[ 30.159320] show_stack+0x18/0x30
[ 30.162729] dump_stack_lvl+0x68/0x84
[ 30.166491] print_address_description.constprop.0+0x74/0x2b8
[ 30.172346] kasan_report+0x1e8/0x250
[ 30.176102] __asan_load8+0x98/0xe0
[ 30.179682] prestera_netdev_port_event.constprop.0+0x68/0x538 [prestera]
[ 30.186847] prestera_netdev_event_handler+0x1b4/0x1c0 [prestera]
[ 30.193313] raw_notifier_call_chain+0x74/0xa0
[ 30.197860] call_netdevice_notifiers_info+0x68/0xc0
[ 30.202924] register_netdevice+0x3cc/0x760
[ 30.207190] register_netdev+0x24/0x50
[ 30.211015] prestera_device_register+0x8a0/0xba0 [prestera]
🎖@cveNotify
🚨 CVE-2021-47103
In the Linux kernel, the following vulnerability has been resolved:
inet: fully convert sk->sk_rx_dst to RCU rules
syzbot reported various issues around early demux,
one being included in this changelog [1]
sk->sk_rx_dst is using RCU protection without clearly
documenting it.
And following sequences in tcp_v4_do_rcv()/tcp_v6_do_rcv()
are not following standard RCU rules.
[a] dst_release(dst);
[b] sk->sk_rx_dst = NULL;
They look wrong because a delete operation of RCU protected
pointer is supposed to clear the pointer before
the call_rcu()/synchronize_rcu() guarding actual memory freeing.
In some cases indeed, dst could be freed before [b] is done.
We could cheat by clearing sk_rx_dst before calling
dst_release(), but this seems the right time to stick
to standard RCU annotations and debugging facilities.
[1]
BUG: KASAN: use-after-free in dst_check include/net/dst.h:470 [inline]
BUG: KASAN: use-after-free in tcp_v4_early_demux+0x95b/0x960 net/ipv4/tcp_ipv4.c:1792
Read of size 2 at addr ffff88807f1cb73a by task syz-executor.5/9204
CPU: 0 PID: 9204 Comm: syz-executor.5 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x320 mm/kasan/report.c:247
__kasan_report mm/kasan/report.c:433 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:450
dst_check include/net/dst.h:470 [inline]
tcp_v4_early_demux+0x95b/0x960 net/ipv4/tcp_ipv4.c:1792
ip_rcv_finish_core.constprop.0+0x15de/0x1e80 net/ipv4/ip_input.c:340
ip_list_rcv_finish.constprop.0+0x1b2/0x6e0 net/ipv4/ip_input.c:583
ip_sublist_rcv net/ipv4/ip_input.c:609 [inline]
ip_list_rcv+0x34e/0x490 net/ipv4/ip_input.c:644
__netif_receive_skb_list_ptype net/core/dev.c:5508 [inline]
__netif_receive_skb_list_core+0x549/0x8e0 net/core/dev.c:5556
__netif_receive_skb_list net/core/dev.c:5608 [inline]
netif_receive_skb_list_internal+0x75e/0xd80 net/core/dev.c:5699
gro_normal_list net/core/dev.c:5853 [inline]
gro_normal_list net/core/dev.c:5849 [inline]
napi_complete_done+0x1f1/0x880 net/core/dev.c:6590
virtqueue_napi_complete drivers/net/virtio_net.c:339 [inline]
virtnet_poll+0xca2/0x11b0 drivers/net/virtio_net.c:1557
__napi_poll+0xaf/0x440 net/core/dev.c:7023
napi_poll net/core/dev.c:7090 [inline]
net_rx_action+0x801/0xb40 net/core/dev.c:7177
__do_softirq+0x29b/0x9c2 kernel/softirq.c:558
invoke_softirq kernel/softirq.c:432 [inline]
__irq_exit_rcu+0x123/0x180 kernel/softirq.c:637
irq_exit_rcu+0x5/0x20 kernel/softirq.c:649
common_interrupt+0x52/0xc0 arch/x86/kernel/irq.c:240
asm_common_interrupt+0x1e/0x40 arch/x86/include/asm/idtentry.h:629
RIP: 0033:0x7f5e972bfd57
Code: 39 d1 73 14 0f 1f 80 00 00 00 00 48 8b 50 f8 48 83 e8 08 48 39 ca 77 f3 48 39 c3 73 3e 48 89 13 48 8b 50 f8 48 89 38 49 8b 0e <48> 8b 3e 48 83 c3 08 48 83 c6 08 eb bc 48 39 d1 72 9e 48 39 d0 73
RSP: 002b:00007fff8a413210 EFLAGS: 00000283
RAX: 00007f5e97108990 RBX: 00007f5e97108338 RCX: ffffffff81d3aa45
RDX: ffffffff81d3aa45 RSI: 00007f5e97108340 RDI: ffffffff81d3aa45
RBP: 00007f5e97107eb8 R08: 00007f5e97108d88 R09: 0000000093c2e8d9
R10: 0000000000000000 R11: 0000000000000000 R12: 00007f5e97107eb0
R13: 00007f5e97108338 R14: 00007f5e97107ea8 R15: 0000000000000019
</TASK>
Allocated by task 13:
kasan_save_stack+0x1e/0x50 mm/kasan/common.c:38
kasan_set_track mm/kasan/common.c:46 [inline]
set_alloc_info mm/kasan/common.c:434 [inline]
__kasan_slab_alloc+0x90/0xc0 mm/kasan/common.c:467
kasan_slab_alloc include/linux/kasan.h:259 [inline]
slab_post_alloc_hook mm/slab.h:519 [inline]
slab_alloc_node mm/slub.c:3234 [inline]
slab_alloc mm/slub.c:3242 [inline]
kmem_cache_alloc+0x202/0x3a0 mm/slub.c:3247
dst_alloc+0x146/0x1f0 net/core/dst.c:92
rt_dst_alloc+0x73/0x430 net/ipv4/route.c:1613
ip_route_input_slow+0x1817/0x3a20 net/ipv4/route.c:234
---truncated---
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
inet: fully convert sk->sk_rx_dst to RCU rules
syzbot reported various issues around early demux,
one being included in this changelog [1]
sk->sk_rx_dst is using RCU protection without clearly
documenting it.
And following sequences in tcp_v4_do_rcv()/tcp_v6_do_rcv()
are not following standard RCU rules.
[a] dst_release(dst);
[b] sk->sk_rx_dst = NULL;
They look wrong because a delete operation of RCU protected
pointer is supposed to clear the pointer before
the call_rcu()/synchronize_rcu() guarding actual memory freeing.
In some cases indeed, dst could be freed before [b] is done.
We could cheat by clearing sk_rx_dst before calling
dst_release(), but this seems the right time to stick
to standard RCU annotations and debugging facilities.
[1]
BUG: KASAN: use-after-free in dst_check include/net/dst.h:470 [inline]
BUG: KASAN: use-after-free in tcp_v4_early_demux+0x95b/0x960 net/ipv4/tcp_ipv4.c:1792
Read of size 2 at addr ffff88807f1cb73a by task syz-executor.5/9204
CPU: 0 PID: 9204 Comm: syz-executor.5 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x320 mm/kasan/report.c:247
__kasan_report mm/kasan/report.c:433 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:450
dst_check include/net/dst.h:470 [inline]
tcp_v4_early_demux+0x95b/0x960 net/ipv4/tcp_ipv4.c:1792
ip_rcv_finish_core.constprop.0+0x15de/0x1e80 net/ipv4/ip_input.c:340
ip_list_rcv_finish.constprop.0+0x1b2/0x6e0 net/ipv4/ip_input.c:583
ip_sublist_rcv net/ipv4/ip_input.c:609 [inline]
ip_list_rcv+0x34e/0x490 net/ipv4/ip_input.c:644
__netif_receive_skb_list_ptype net/core/dev.c:5508 [inline]
__netif_receive_skb_list_core+0x549/0x8e0 net/core/dev.c:5556
__netif_receive_skb_list net/core/dev.c:5608 [inline]
netif_receive_skb_list_internal+0x75e/0xd80 net/core/dev.c:5699
gro_normal_list net/core/dev.c:5853 [inline]
gro_normal_list net/core/dev.c:5849 [inline]
napi_complete_done+0x1f1/0x880 net/core/dev.c:6590
virtqueue_napi_complete drivers/net/virtio_net.c:339 [inline]
virtnet_poll+0xca2/0x11b0 drivers/net/virtio_net.c:1557
__napi_poll+0xaf/0x440 net/core/dev.c:7023
napi_poll net/core/dev.c:7090 [inline]
net_rx_action+0x801/0xb40 net/core/dev.c:7177
__do_softirq+0x29b/0x9c2 kernel/softirq.c:558
invoke_softirq kernel/softirq.c:432 [inline]
__irq_exit_rcu+0x123/0x180 kernel/softirq.c:637
irq_exit_rcu+0x5/0x20 kernel/softirq.c:649
common_interrupt+0x52/0xc0 arch/x86/kernel/irq.c:240
asm_common_interrupt+0x1e/0x40 arch/x86/include/asm/idtentry.h:629
RIP: 0033:0x7f5e972bfd57
Code: 39 d1 73 14 0f 1f 80 00 00 00 00 48 8b 50 f8 48 83 e8 08 48 39 ca 77 f3 48 39 c3 73 3e 48 89 13 48 8b 50 f8 48 89 38 49 8b 0e <48> 8b 3e 48 83 c3 08 48 83 c6 08 eb bc 48 39 d1 72 9e 48 39 d0 73
RSP: 002b:00007fff8a413210 EFLAGS: 00000283
RAX: 00007f5e97108990 RBX: 00007f5e97108338 RCX: ffffffff81d3aa45
RDX: ffffffff81d3aa45 RSI: 00007f5e97108340 RDI: ffffffff81d3aa45
RBP: 00007f5e97107eb8 R08: 00007f5e97108d88 R09: 0000000093c2e8d9
R10: 0000000000000000 R11: 0000000000000000 R12: 00007f5e97107eb0
R13: 00007f5e97108338 R14: 00007f5e97107ea8 R15: 0000000000000019
</TASK>
Allocated by task 13:
kasan_save_stack+0x1e/0x50 mm/kasan/common.c:38
kasan_set_track mm/kasan/common.c:46 [inline]
set_alloc_info mm/kasan/common.c:434 [inline]
__kasan_slab_alloc+0x90/0xc0 mm/kasan/common.c:467
kasan_slab_alloc include/linux/kasan.h:259 [inline]
slab_post_alloc_hook mm/slab.h:519 [inline]
slab_alloc_node mm/slub.c:3234 [inline]
slab_alloc mm/slub.c:3242 [inline]
kmem_cache_alloc+0x202/0x3a0 mm/slub.c:3247
dst_alloc+0x146/0x1f0 net/core/dst.c:92
rt_dst_alloc+0x73/0x430 net/ipv4/route.c:1613
ip_route_input_slow+0x1817/0x3a20 net/ipv4/route.c:234
---truncated---
🎖@cveNotify
🚨 CVE-2021-47106
In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: fix use-after-free in nft_set_catchall_destroy()
We need to use list_for_each_entry_safe() iterator
because we can not access @catchall after kfree_rcu() call.
syzbot reported:
BUG: KASAN: use-after-free in nft_set_catchall_destroy net/netfilter/nf_tables_api.c:4486 [inline]
BUG: KASAN: use-after-free in nft_set_destroy net/netfilter/nf_tables_api.c:4504 [inline]
BUG: KASAN: use-after-free in nft_set_destroy+0x3fd/0x4f0 net/netfilter/nf_tables_api.c:4493
Read of size 8 at addr ffff8880716e5b80 by task syz-executor.3/8871
CPU: 1 PID: 8871 Comm: syz-executor.3 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x2ed mm/kasan/report.c:247
__kasan_report mm/kasan/report.c:433 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:450
nft_set_catchall_destroy net/netfilter/nf_tables_api.c:4486 [inline]
nft_set_destroy net/netfilter/nf_tables_api.c:4504 [inline]
nft_set_destroy+0x3fd/0x4f0 net/netfilter/nf_tables_api.c:4493
__nft_release_table+0x79f/0xcd0 net/netfilter/nf_tables_api.c:9626
nft_rcv_nl_event+0x4f8/0x670 net/netfilter/nf_tables_api.c:9688
notifier_call_chain+0xb5/0x200 kernel/notifier.c:83
blocking_notifier_call_chain kernel/notifier.c:318 [inline]
blocking_notifier_call_chain+0x67/0x90 kernel/notifier.c:306
netlink_release+0xcb6/0x1dd0 net/netlink/af_netlink.c:788
__sock_release+0xcd/0x280 net/socket.c:649
sock_close+0x18/0x20 net/socket.c:1314
__fput+0x286/0x9f0 fs/file_table.c:280
task_work_run+0xdd/0x1a0 kernel/task_work.c:164
tracehook_notify_resume include/linux/tracehook.h:189 [inline]
exit_to_user_mode_loop kernel/entry/common.c:175 [inline]
exit_to_user_mode_prepare+0x27e/0x290 kernel/entry/common.c:207
__syscall_exit_to_user_mode_work kernel/entry/common.c:289 [inline]
syscall_exit_to_user_mode+0x19/0x60 kernel/entry/common.c:300
do_syscall_64+0x42/0xb0 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f75fbf28adb
Code: 0f 05 48 3d 00 f0 ff ff 77 45 c3 0f 1f 40 00 48 83 ec 18 89 7c 24 0c e8 63 fc ff ff 8b 7c 24 0c 41 89 c0 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 35 44 89 c7 89 44 24 0c e8 a1 fc ff ff 8b 44
RSP: 002b:00007ffd8da7ec10 EFLAGS: 00000293 ORIG_RAX: 0000000000000003
RAX: 0000000000000000 RBX: 0000000000000004 RCX: 00007f75fbf28adb
RDX: 00007f75fc08e828 RSI: ffffffffffffffff RDI: 0000000000000003
RBP: 00007f75fc08a960 R08: 0000000000000000 R09: 00007f75fc08e830
R10: 00007ffd8da7ed10 R11: 0000000000000293 R12: 00000000002067c3
R13: 00007ffd8da7ed10 R14: 00007f75fc088f60 R15: 0000000000000032
</TASK>
Allocated by task 8886:
kasan_save_stack+0x1e/0x50 mm/kasan/common.c:38
kasan_set_track mm/kasan/common.c:46 [inline]
set_alloc_info mm/kasan/common.c:434 [inline]
____kasan_kmalloc mm/kasan/common.c:513 [inline]
____kasan_kmalloc mm/kasan/common.c:472 [inline]
__kasan_kmalloc+0xa6/0xd0 mm/kasan/common.c:522
kasan_kmalloc include/linux/kasan.h:269 [inline]
kmem_cache_alloc_trace+0x1ea/0x4a0 mm/slab.c:3575
kmalloc include/linux/slab.h:590 [inline]
nft_setelem_catchall_insert net/netfilter/nf_tables_api.c:5544 [inline]
nft_setelem_insert net/netfilter/nf_tables_api.c:5562 [inline]
nft_add_set_elem+0x232e/0x2f40 net/netfilter/nf_tables_api.c:5936
nf_tables_newsetelem+0x6ff/0xbb0 net/netfilter/nf_tables_api.c:6032
nfnetlink_rcv_batch+0x1710/0x25f0 net/netfilter/nfnetlink.c:513
nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline]
nfnetlink_rcv+0x3af/0x420 net/netfilter/nfnetlink.c:652
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x904/0xdf0 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/
---truncated---
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: fix use-after-free in nft_set_catchall_destroy()
We need to use list_for_each_entry_safe() iterator
because we can not access @catchall after kfree_rcu() call.
syzbot reported:
BUG: KASAN: use-after-free in nft_set_catchall_destroy net/netfilter/nf_tables_api.c:4486 [inline]
BUG: KASAN: use-after-free in nft_set_destroy net/netfilter/nf_tables_api.c:4504 [inline]
BUG: KASAN: use-after-free in nft_set_destroy+0x3fd/0x4f0 net/netfilter/nf_tables_api.c:4493
Read of size 8 at addr ffff8880716e5b80 by task syz-executor.3/8871
CPU: 1 PID: 8871 Comm: syz-executor.3 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x2ed mm/kasan/report.c:247
__kasan_report mm/kasan/report.c:433 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:450
nft_set_catchall_destroy net/netfilter/nf_tables_api.c:4486 [inline]
nft_set_destroy net/netfilter/nf_tables_api.c:4504 [inline]
nft_set_destroy+0x3fd/0x4f0 net/netfilter/nf_tables_api.c:4493
__nft_release_table+0x79f/0xcd0 net/netfilter/nf_tables_api.c:9626
nft_rcv_nl_event+0x4f8/0x670 net/netfilter/nf_tables_api.c:9688
notifier_call_chain+0xb5/0x200 kernel/notifier.c:83
blocking_notifier_call_chain kernel/notifier.c:318 [inline]
blocking_notifier_call_chain+0x67/0x90 kernel/notifier.c:306
netlink_release+0xcb6/0x1dd0 net/netlink/af_netlink.c:788
__sock_release+0xcd/0x280 net/socket.c:649
sock_close+0x18/0x20 net/socket.c:1314
__fput+0x286/0x9f0 fs/file_table.c:280
task_work_run+0xdd/0x1a0 kernel/task_work.c:164
tracehook_notify_resume include/linux/tracehook.h:189 [inline]
exit_to_user_mode_loop kernel/entry/common.c:175 [inline]
exit_to_user_mode_prepare+0x27e/0x290 kernel/entry/common.c:207
__syscall_exit_to_user_mode_work kernel/entry/common.c:289 [inline]
syscall_exit_to_user_mode+0x19/0x60 kernel/entry/common.c:300
do_syscall_64+0x42/0xb0 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f75fbf28adb
Code: 0f 05 48 3d 00 f0 ff ff 77 45 c3 0f 1f 40 00 48 83 ec 18 89 7c 24 0c e8 63 fc ff ff 8b 7c 24 0c 41 89 c0 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 35 44 89 c7 89 44 24 0c e8 a1 fc ff ff 8b 44
RSP: 002b:00007ffd8da7ec10 EFLAGS: 00000293 ORIG_RAX: 0000000000000003
RAX: 0000000000000000 RBX: 0000000000000004 RCX: 00007f75fbf28adb
RDX: 00007f75fc08e828 RSI: ffffffffffffffff RDI: 0000000000000003
RBP: 00007f75fc08a960 R08: 0000000000000000 R09: 00007f75fc08e830
R10: 00007ffd8da7ed10 R11: 0000000000000293 R12: 00000000002067c3
R13: 00007ffd8da7ed10 R14: 00007f75fc088f60 R15: 0000000000000032
</TASK>
Allocated by task 8886:
kasan_save_stack+0x1e/0x50 mm/kasan/common.c:38
kasan_set_track mm/kasan/common.c:46 [inline]
set_alloc_info mm/kasan/common.c:434 [inline]
____kasan_kmalloc mm/kasan/common.c:513 [inline]
____kasan_kmalloc mm/kasan/common.c:472 [inline]
__kasan_kmalloc+0xa6/0xd0 mm/kasan/common.c:522
kasan_kmalloc include/linux/kasan.h:269 [inline]
kmem_cache_alloc_trace+0x1ea/0x4a0 mm/slab.c:3575
kmalloc include/linux/slab.h:590 [inline]
nft_setelem_catchall_insert net/netfilter/nf_tables_api.c:5544 [inline]
nft_setelem_insert net/netfilter/nf_tables_api.c:5562 [inline]
nft_add_set_elem+0x232e/0x2f40 net/netfilter/nf_tables_api.c:5936
nf_tables_newsetelem+0x6ff/0xbb0 net/netfilter/nf_tables_api.c:6032
nfnetlink_rcv_batch+0x1710/0x25f0 net/netfilter/nfnetlink.c:513
nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline]
nfnetlink_rcv+0x3af/0x420 net/netfilter/nfnetlink.c:652
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x904/0xdf0 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/
---truncated---
🎖@cveNotify
🚨 CVE-2021-47107
In the Linux kernel, the following vulnerability has been resolved:
NFSD: Fix READDIR buffer overflow
If a client sends a READDIR count argument that is too small (say,
zero), then the buffer size calculation in the new init_dirlist
helper functions results in an underflow, allowing the XDR stream
functions to write beyond the actual buffer.
This calculation has always been suspect. NFSD has never sanity-
checked the READDIR count argument, but the old entry encoders
managed the problem correctly.
With the commits below, entry encoding changed, exposing the
underflow to the pointer arithmetic in xdr_reserve_space().
Modern NFS clients attempt to retrieve as much data as possible
for each READDIR request. Also, we have no unit tests that
exercise the behavior of READDIR at the lower bound of @count
values. Thus this case was missed during testing.
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
NFSD: Fix READDIR buffer overflow
If a client sends a READDIR count argument that is too small (say,
zero), then the buffer size calculation in the new init_dirlist
helper functions results in an underflow, allowing the XDR stream
functions to write beyond the actual buffer.
This calculation has always been suspect. NFSD has never sanity-
checked the READDIR count argument, but the old entry encoders
managed the problem correctly.
With the commits below, entry encoding changed, exposing the
underflow to the pointer arithmetic in xdr_reserve_space().
Modern NFS clients attempt to retrieve as much data as possible
for each READDIR request. Also, we have no unit tests that
exercise the behavior of READDIR at the lower bound of @count
values. Thus this case was missed during testing.
🎖@cveNotify
🚨 CVE-2022-48629
In the Linux kernel, the following vulnerability has been resolved:
crypto: qcom-rng - ensure buffer for generate is completely filled
The generate function in struct rng_alg expects that the destination
buffer is completely filled if the function returns 0. qcom_rng_read()
can run into a situation where the buffer is partially filled with
randomness and the remaining part of the buffer is zeroed since
qcom_rng_generate() doesn't check the return value. This issue can
be reproduced by running the following from libkcapi:
kcapi-rng -b 9000000 > OUTFILE
The generated OUTFILE will have three huge sections that contain all
zeros, and this is caused by the code where the test
'val & PRNG_STATUS_DATA_AVAIL' fails.
Let's fix this issue by ensuring that qcom_rng_read() always returns
with a full buffer if the function returns success. Let's also have
qcom_rng_generate() return the correct value.
Here's some statistics from the ent project
(https://www.fourmilab.ch/random/) that shows information about the
quality of the generated numbers:
$ ent -c qcom-random-before
Value Char Occurrences Fraction
0 606748 0.067416
1 33104 0.003678
2 33001 0.003667
...
253 � 32883 0.003654
254 � 33035 0.003671
255 � 33239 0.003693
Total: 9000000 1.000000
Entropy = 7.811590 bits per byte.
Optimum compression would reduce the size
of this 9000000 byte file by 2 percent.
Chi square distribution for 9000000 samples is 9329962.81, and
randomly would exceed this value less than 0.01 percent of the
times.
Arithmetic mean value of data bytes is 119.3731 (127.5 = random).
Monte Carlo value for Pi is 3.197293333 (error 1.77 percent).
Serial correlation coefficient is 0.159130 (totally uncorrelated =
0.0).
Without this patch, the results of the chi-square test is 0.01%, and
the numbers are certainly not random according to ent's project page.
The results improve with this patch:
$ ent -c qcom-random-after
Value Char Occurrences Fraction
0 35432 0.003937
1 35127 0.003903
2 35424 0.003936
...
253 � 35201 0.003911
254 � 34835 0.003871
255 � 35368 0.003930
Total: 9000000 1.000000
Entropy = 7.999979 bits per byte.
Optimum compression would reduce the size
of this 9000000 byte file by 0 percent.
Chi square distribution for 9000000 samples is 258.77, and randomly
would exceed this value 42.24 percent of the times.
Arithmetic mean value of data bytes is 127.5006 (127.5 = random).
Monte Carlo value for Pi is 3.141277333 (error 0.01 percent).
Serial correlation coefficient is 0.000468 (totally uncorrelated =
0.0).
This change was tested on a Nexus 5 phone (msm8974 SoC).
🎖@cveNotify
In the Linux kernel, the following vulnerability has been resolved:
crypto: qcom-rng - ensure buffer for generate is completely filled
The generate function in struct rng_alg expects that the destination
buffer is completely filled if the function returns 0. qcom_rng_read()
can run into a situation where the buffer is partially filled with
randomness and the remaining part of the buffer is zeroed since
qcom_rng_generate() doesn't check the return value. This issue can
be reproduced by running the following from libkcapi:
kcapi-rng -b 9000000 > OUTFILE
The generated OUTFILE will have three huge sections that contain all
zeros, and this is caused by the code where the test
'val & PRNG_STATUS_DATA_AVAIL' fails.
Let's fix this issue by ensuring that qcom_rng_read() always returns
with a full buffer if the function returns success. Let's also have
qcom_rng_generate() return the correct value.
Here's some statistics from the ent project
(https://www.fourmilab.ch/random/) that shows information about the
quality of the generated numbers:
$ ent -c qcom-random-before
Value Char Occurrences Fraction
0 606748 0.067416
1 33104 0.003678
2 33001 0.003667
...
253 � 32883 0.003654
254 � 33035 0.003671
255 � 33239 0.003693
Total: 9000000 1.000000
Entropy = 7.811590 bits per byte.
Optimum compression would reduce the size
of this 9000000 byte file by 2 percent.
Chi square distribution for 9000000 samples is 9329962.81, and
randomly would exceed this value less than 0.01 percent of the
times.
Arithmetic mean value of data bytes is 119.3731 (127.5 = random).
Monte Carlo value for Pi is 3.197293333 (error 1.77 percent).
Serial correlation coefficient is 0.159130 (totally uncorrelated =
0.0).
Without this patch, the results of the chi-square test is 0.01%, and
the numbers are certainly not random according to ent's project page.
The results improve with this patch:
$ ent -c qcom-random-after
Value Char Occurrences Fraction
0 35432 0.003937
1 35127 0.003903
2 35424 0.003936
...
253 � 35201 0.003911
254 � 34835 0.003871
255 � 35368 0.003930
Total: 9000000 1.000000
Entropy = 7.999979 bits per byte.
Optimum compression would reduce the size
of this 9000000 byte file by 0 percent.
Chi square distribution for 9000000 samples is 258.77, and randomly
would exceed this value 42.24 percent of the times.
Arithmetic mean value of data bytes is 127.5006 (127.5 = random).
Monte Carlo value for Pi is 3.141277333 (error 0.01 percent).
Serial correlation coefficient is 0.000468 (totally uncorrelated =
0.0).
This change was tested on a Nexus 5 phone (msm8974 SoC).
🎖@cveNotify