🚨 CVE-2026-43488
In the Linux kernel, the following vulnerability has been resolved:

usb: xhci: Prevent interrupt storm on host controller error (HCE)

The xHCI controller reports a Host Controller Error (HCE) in UAS Storage
Device plug/unplug scenarios on Android devices. HCE is checked in
xhci_irq() function and causes an interrupt storm (since the interrupt
isn’t cleared), leading to severe system-level faults.

When the xHC controller reports HCE in the interrupt handler, the driver
only logs a warning and assumes xHC activity will stop as stated in xHCI
specification. An interrupt storm does however continue on some hosts
even after HCE, and only ceases after manually disabling xHC interrupt
and stopping the controller by calling xhci_halt().

Add xhci_halt() to xhci_irq() function where STS_HCE status is checked,
mirroring the existing error handling pattern used for STS_FATAL errors.

This only fixes the interrupt storm. Proper HCE recovery requires resetting
and re-initializing the xHC.

🎖@cveNotify

🚨 CVE-2026-43489
In the Linux kernel, the following vulnerability has been resolved:

liveupdate: luo_file: remember retrieve() status

LUO keeps track of successful retrieve attempts on a LUO file. It does so
to avoid multiple retrievals of the same file. Multiple retrievals cause
problems because once the file is retrieved, the serialized data
structures are likely freed and the file is likely in a very different
state from what the code expects.

The retrieve boolean in struct luo_file keeps track of this, and is passed
to the finish callback so it knows what work was already done and what it
has left to do.

All this works well when retrieve succeeds. When it fails,
luo_retrieve_file() returns the error immediately, without ever storing
anywhere that a retrieve was attempted or what its error code was. This
results in an errored LIVEUPDATE_SESSION_RETRIEVE_FD ioctl to userspace,
but nothing prevents it from trying this again.

The retry is problematic for much of the same reasons listed above. The
file is likely in a very different state than what the retrieve logic
normally expects, and it might even have freed some serialization data
structures. Attempting to access them or free them again is going to
break things.

For example, if memfd managed to restore 8 of its 10 folios, but fails on
the 9th, a subsequent retrieve attempt will try to call
kho_restore_folio() on the first folio again, and that will fail with a
warning since it is an invalid operation.

Apart from the retry, finish() also breaks. Since on failure the
retrieved bool in luo_file is never touched, the finish() call on session
close will tell the file handler that retrieve was never attempted, and it
will try to access or free the data structures that might not exist, much
in the same way as the retry attempt.

There is no sane way of attempting the retrieve again. Remember the error
retrieve returned and directly return it on a retry. Also pass this
status code to finish() so it can make the right decision on the work it
needs to do.

This is done by changing the bool to an integer. A value of 0 means
retrieve was never attempted, a positive value means it succeeded, and a
negative value means it failed and the error code is the value.

🎖@cveNotify

🚨 CVE-2026-43490
In the Linux kernel, the following vulnerability has been resolved:

ksmbd: validate inherited ACE SID length

smb_inherit_dacl() walks the parent directory DACL loaded from the
security descriptor xattr. It verifies that each ACE contains the fixed
SID header before using it, but does not verify that the variable-length
SID described by sid.num_subauth is fully contained in the ACE.

A malformed inheritable ACE can advertise more subauthorities than are
present in the ACE. compare_sids() may then read past the ACE.
smb_set_ace() also clamps the copied destination SID, but used the
unchecked source SID count to compute the inherited ACE size. That could
advance the temporary inherited ACE buffer pointer and nt_size accounting
past the allocated buffer.

Fix this by validating the parent ACE SID count and SID length before
using the SID during inheritance. Compute the inherited ACE size from the
copied SID so the size matches the bounded destination SID. Reject the
inherited DACL if size accumulation would overflow smb_acl.size or the
security descriptor allocation size.

🎖@cveNotify

🚨 CVE-2026-43491
In the Linux kernel, the following vulnerability has been resolved:

net: qrtr: ns: Limit the maximum server registration per node

Current code does no bound checking on the number of servers added per
node. A malicious client can flood NEW_SERVER messages and exhaust memory.

Fix this issue by limiting the maximum number of server registrations to
256 per node. If the NEW_SERVER message is received for an old port, then
don't restrict it as it will get replaced. While at it, also rate limit
the error messages in the failure path of qrtr_ns_worker().

Note that the limit of 256 is chosen based on the current platform
requirements. If requirement changes in the future, this limit can be
increased.

🎖@cveNotify

🚨 CVE-2026-43503
In the Linux kernel, the following vulnerability has been resolved:

net: skbuff: propagate shared-frag marker through frag-transfer helpers

Two frag-transfer helpers (__pskb_copy_fclone() and skb_shift()) fail
to propagate the SKBFL_SHARED_FRAG bit in skb_shinfo()->flags when
moving frags from source to destination. __pskb_copy_fclone() defers
the rest of the shinfo metadata to skb_copy_header() after copying
frag descriptors, but that helper only carries over gso_{size,segs,
type} and never touches skb_shinfo()->flags; skb_shift() moves frag
descriptors directly and leaves flags untouched. As a result, the
destination skb keeps a reference to the same externally-owned or
page-cache-backed pages while reporting skb_has_shared_frag() as
false.

The mismatch is harmful in any in-place writer that uses
skb_has_shared_frag() to decide whether shared pages must be detoured
through skb_cow_data(). ESP input is one such writer (esp4.c,
esp6.c), and a single nft 'dup to <local>' rule -- or any other
nf_dup_ipv4() / xt_TEE caller -- is enough to land a pskb_copy()'d
skb in esp_input() with the marker stripped, letting an unprivileged
user write into the page cache of a root-owned read-only file via
authencesn-ESN stray writes.

Set SKBFL_SHARED_FRAG on the destination whenever frag descriptors
were actually moved from the source. skb_copy() and skb_copy_expand()
share skb_copy_header() too but linearize all paged data into freshly
allocated head storage and emerge with nr_frags == 0, so
skb_has_shared_frag() returns false on its own; they need no change.

The same omission exists in skb_gro_receive() and skb_gro_receive_list().
The former moves the incoming skb's frag descriptors into the
accumulator's last sub-skb via two paths (a direct frag-move loop and
the head_frag + memcpy path); the latter chains the incoming skb whole
onto p's frag_list. Downstream skb_segment() reads only
skb_shinfo(p)->flags, and skb_segment_list() reuses each sub-skb's
shinfo as the nskb -- both p and lp must carry the marker.

The same omission also exists in tcp_clone_payload(), which builds an
MTU probe skb by moving frag descriptors from skbs on sk_write_queue
into a freshly allocated nskb. The helper falls into the same family
and warrants the same fix for consistency; no TCP TX-side in-place
writer is currently known to reach a user page through this gap, but
a future consumer depending on the marker would regress silently.

The same omission exists in skb_segment(): the per-iteration flag
merge takes only head_skb's flag, and the inner switch that rebinds
frag_skb to list_skb on head_skb-frags exhaustion does not fold the
new frag_skb's flag into nskb. Fold frag_skb's flag at both sites
so segments drawing frags from frag_list members carry the marker.

🎖@cveNotify

🚨 CVE-2026-45834
In the Linux kernel, the following vulnerability has been resolved:

Bluetooth: L2CAP: Fix null-ptr-deref in l2cap_sock_state_change_cb()

Add the same NULL guard already present in
l2cap_sock_resume_cb() and l2cap_sock_ready_cb().

🎖@cveNotify

🚨 CVE-2026-45835
In the Linux kernel, the following vulnerability has been resolved:

Bluetooth: L2CAP: Fix null-ptr-deref in l2cap_sock_new_connection_cb()

Add the same NULL guard already present in
l2cap_sock_resume_cb() and l2cap_sock_ready_cb().

🎖@cveNotify

🚨 CVE-2026-45836
In the Linux kernel, the following vulnerability has been resolved:

Bluetooth: L2CAP: Fix null-ptr-deref in l2cap_sock_get_sndtimeo_cb()

Add the same NULL guard already present in
l2cap_sock_resume_cb() and l2cap_sock_ready_cb().

🎖@cveNotify

🚨 CVE-2026-45837
In the Linux kernel, the following vulnerability has been resolved:

bpf: Fix use-after-free in arena_vm_close on fork

arena_vm_open() only bumps vml->mmap_count but never registers the
child VMA in arena->vma_list. The vml->vma always points at the
parent VMA, so after parent munmap the pointer dangles. If the child
then calls bpf_arena_free_pages(), zap_pages() reads the stale
vml->vma triggering use-after-free.

Fix this by preventing the arena VMA from being inherited across
fork with VM_DONTCOPY, and preventing VMA splits via the may_split
callback.

Also reject mremap with a .mremap callback returning -EINVAL. A
same-size mremap(MREMAP_FIXED) on the full arena VMA reaches
copy_vma() through the following path:

check_prep_vma() - returns 0 early: new_len == old_len
skips VM_DONTEXPAND check
prep_move_vma() - vm_start == old_addr and
vm_end == old_addr + old_len
so may_split is never called
move_vma()
copy_vma_and_data()
copy_vma()
vm_area_dup() - copies vm_private_data (vml pointer)
vm_ops->open() - bumps vml->mmap_count
vm_ops->mremap() - returns -EINVAL, rollback unmaps new VMA

The refcount ensures the rollback's arena_vm_close does not free
the vml shared with the original VMA.

🎖@cveNotify

🚨 CVE-2026-45838
In the Linux kernel, the following vulnerability has been resolved:

bpf: fix end-of-list detection in cgroup_storage_get_next_key()

list_next_entry() never returns NULL -- when the current element is the
last entry it wraps to the list head via container_of(). The subsequent
NULL check is therefore dead code and get_next_key() never returns
-ENOENT for the last element, instead reading storage->key from a bogus
pointer that aliases internal map fields and copying the result to
userspace.

Replace it with list_entry_is_head() so the function correctly returns
-ENOENT when there are no more entries.

🎖@cveNotify

🚨 CVE-2026-45839
In the Linux kernel, the following vulnerability has been resolved:

bpf: reject negative CO-RE accessor indices in bpf_core_parse_spec()

CO-RE accessor strings are colon-separated indices that describe a path
from a root BTF type to a target field, e.g. "0:1:2" walks through
nested struct members. bpf_core_parse_spec() parses each component with
sscanf("%d"), so negative values like -1 are silently accepted. The
subsequent bounds checks (access_idx >= btf_vlen(t)) only guard the
upper bound and always pass for negative values because C integer
promotion converts the __u16 btf_vlen result to int, making the
comparison (int)(-1) >= (int)(N) false for any positive N.

When -1 reaches btf_member_bit_offset() it gets cast to u32 0xffffffff,
producing an out-of-bounds read far past the members array. A crafted
BPF program with a negative CO-RE accessor on any struct that exists in
vmlinux BTF (e.g. task_struct) crashes the kernel deterministically
during BPF_PROG_LOAD on any system with CONFIG_DEBUG_INFO_BTF=y
(default on major distributions). The bug is reachable with CAP_BPF:

BUG: unable to handle page fault for address: ffffed11818b6626
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
Oops: Oops: 0000 [#1] SMP KASAN NOPTI
CPU: 0 UID: 0 PID: 85 Comm: poc Not tainted 7.0.0-rc6 #18 PREEMPT(full)
RIP: 0010:bpf_core_parse_spec (tools/lib/bpf/relo_core.c:354)
RAX: 00000000ffffffff
Call Trace:
<TASK>
bpf_core_calc_relo_insn (tools/lib/bpf/relo_core.c:1321)
bpf_core_apply (kernel/bpf/btf.c:9507)
check_core_relo (kernel/bpf/verifier.c:19475)
bpf_check (kernel/bpf/verifier.c:26031)
bpf_prog_load (kernel/bpf/syscall.c:3089)
__sys_bpf (kernel/bpf/syscall.c:6228)
</TASK>

CO-RE accessor indices are inherently non-negative (struct member index,
array element index, or enumerator index), so reject them immediately
after parsing.

🎖@cveNotify

🚨 CVE-2026-45840
In the Linux kernel, the following vulnerability has been resolved:

openvswitch: cap upcall PID array size and pre-size vport replies

The vport netlink reply helpers allocate a fixed-size skb with
nlmsg_new(NLMSG_DEFAULT_SIZE, ...) but serialize the full upcall PID
array via ovs_vport_get_upcall_portids(). Since
ovs_vport_set_upcall_portids() accepts any non-zero multiple of
sizeof(u32) with no upper bound, a CAP_NET_ADMIN user can install a PID
array large enough to overflow the reply buffer, causing nla_put() to
fail with -EMSGSIZE and hitting BUG_ON(err < 0). On systems with
unprivileged user namespaces enabled (e.g., Ubuntu default), this is
reachable via unshare -Urn since OVS vport mutation operations use
GENL_UNS_ADMIN_PERM.

kernel BUG at net/openvswitch/datapath.c:2414!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 1 UID: 0 PID: 65 Comm: poc Not tainted 7.0.0-rc7-00195-geb216e422044 #1
RIP: 0010:ovs_vport_cmd_set+0x34c/0x400
Call Trace:
<TASK>
genl_family_rcv_msg_doit (net/netlink/genetlink.c:1116)
genl_rcv_msg (net/netlink/genetlink.c:1194)
netlink_rcv_skb (net/netlink/af_netlink.c:2550)
genl_rcv (net/netlink/genetlink.c:1219)
netlink_unicast (net/netlink/af_netlink.c:1344)
netlink_sendmsg (net/netlink/af_netlink.c:1894)
__sys_sendto (net/socket.c:2206)
__x64_sys_sendto (net/socket.c:2209)
do_syscall_64 (arch/x86/entry/syscall_64.c:63)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
</TASK>
Kernel panic - not syncing: Fatal exception

Reject attempts to set more PIDs than nr_cpu_ids in
ovs_vport_set_upcall_portids(), and pre-compute the worst-case reply
size in ovs_vport_cmd_msg_size() based on that bound, similar to the
existing ovs_dp_cmd_msg_size(). nr_cpu_ids matches the cap already
used by the per-CPU dispatch configuration on the datapath side
(ovs_dp_cmd_fill_info() serialises at most nr_cpu_ids PIDs), so the
two sides stay consistent.

🎖@cveNotify

🚨 CVE-2026-48818
Starlette is a lightweight ASGI framework/toolkit. In versions 1.0.1 and earlier, StaticFiles on Windows is vulnerable to SSRF. An UNC path such as \\attacker.com\share can cause os.path.realpath to initiate an outbound SMB connection before the path is rejected, exposing the service account’s NTLMv2 credentials for offline cracking or relay even though the HTTP response is only a 404. The issue affects default follow_symlink=False deployments, including frameworks built on Starlette such as FastAPI; POSIX systems and follow_symlink=True are unaffected. The issue is fixed in 1.1.0.

🎖@cveNotify

🚨 CVE-2026-48817
Starlette is a lightweight ASGI framework/toolkit. In versions 1.0.1 and below, when dispatching a request, HTTPEndpoint selects the handler by lowercasing the HTTP method and looking it up as an attribute with getattr, without restricting the lookup to a known set of HTTP verbs. When an HTTPEndpoint subclass is registered through Route(...) without an explicit methods= argument, the route does not constrain the method and every method reaches the endpoint. If a non-standard HTTP method whose lowercased name matches an attribute on the endpoint subclass reaches the endpoint, that attribute is invoked as if it were a request handler. An attacker can use this to reach methods that were never meant to be HTTP handlers, such as internal helpers, without the authorization checks applied by the intended public handler. An application (including Starlette-based frameworks like FastAPI) is affected if it registers an HTTPEndpoint subclass via Route(...) without explicitly setting methods=, and that subclass includes extra methods named like non-standard HTTP verbs that take one request argument and return a response. This issue has been fixed in version 1.1.0.

🎖@cveNotify

🚨 CVE-2026-55199
libssh2 through 1.11.1, fixed in commit 1762685, contains a pre-authentication denial of service vulnerability in the SSH_MSG_EXT_INFO handler in src/packet.c that allows a malicious SSH server to cause a client CPU exhaustion loop by sending a crafted extension count value. A malicious server can set nr_extensions to 0xFFFFFFFF during key exchange, causing the client to spin in a tight CPU loop for over 60 seconds because return values from _libssh2_get_string() are unchecked and the session timeout does not apply to CPU-bound loops.

🎖@cveNotify

🚨 CVE-2026-55200
libssh2 through 1.11.1, fixed in commit 7acf3df contains an out-of-bounds write vulnerability in ssh2_transport_read() that fails to enforce upper bounds on packet_length field. Remote attackers can send crafted SSH packets with excessively large packet_length values to corrupt heap memory and achieve remote code execution.

🎖@cveNotify

🚨 CVE-2026-49295
libde265 is an open source implementation of the h.265 video codec. Prior to version 1.0.20, a crafted H.265 bitstream can cause an out-of-bounds array write in `decoder_context::process_reference_picture_set()` (`libde265/decctx.cc:1376`). The root cause is a missing aggregate bound check on predicted short-term reference picture set entries. Individual list sizes are validated, but the combined count after predicted RPS construction can exceed the 16-entry `PocStFoll` array, writing at index 16. Version 1.0.20 patches the issue.

🎖@cveNotify

🚨 CVE-2026-49346
libde265 is an open source implementation of the h.265 video codec. Prior to version 1.1.0, a crafted H.265 bitstream with large SPS dimensions and 16-bit bit depth causes a signed integer overflow in `de265_image_get_buffer()` (`libde265/image.cc:128`). The overflow wraps the plane allocation size to a small value (~1 KB), but the subsequent `fill_image()` call computes the real size using `size_t`, writing ~4 GB into the undersized heap buffer. Version 1.1.0 patches the issue.

🎖@cveNotify

🚨 CVE-2026-50557
Angular is a development platform for building mobile and desktop web applications using TypeScript/JavaScript and other languages. Prior to 22.0.0-rc.2, 21.2.15, 20.3.22 and 19.2.22, an issue in the @angular/compiler and @angular/core packages allows bypassing element and attribute sanitization/validation through specific namespace workarounds. Specifically, namespaced script elements (e.g., <svg:script> or <:svg:script>) were not properly identified as script elements by the Angular template preparser, allowing them to pass through template compilation without being stripped. Furthermore, security context schema mappings for element attributes did not consistently handle attributes within namespaced elements (like SVG and MathML), opening up gaps where malicious namespaced attributes could bypass runtime and compile-time sanitizers. Combined, these flaws enable an attacker who can inject or supply a template/tag structure with custom namespaces to bypass Angular's script-stripping logic and attribute sanitizers, leading to client-side Cross-Site Scripting (XSS). This vulnerability is fixed in 22.0.0-rc.2, 21.2.15, 20.3.22 and 19.2.22.

🎖@cveNotify

🚨 CVE-2026-52725
Angular is a development platform for building mobile and desktop web applications using TypeScript/JavaScript and other languages. Prior to 22.0.0-rc.2, 21.2.15, 20.3.22, and 19.2.23, an issue in the @angular/core package allows bypassing script-execution restrictions during dynamic component creation. Specifically, the dynamic component instantiation mechanism (createComponent) failed to reject mounting components directly onto a <script> or namespaced script element (such as <svg:script>). This enabled the initialization of custom components on a tag that executes scripts, allowing attackers to hijack or inject script-executing hosts. This flaw enables an attacker who can control the host element or selector parameter passed to createComponent to initialize or mount an Angular component directly onto a <script> tag, leading to execution of untrusted code or client-side Cross-Site Scripting (XSS). This vulnerability is fixed in 22.0.0-rc.2, 21.2.15, 20.3.22, and 19.2.23.

🎖@cveNotify

🚨 CVE-2026-54264
Angular is a development platform for building mobile and desktop web applications using TypeScript/JavaScript and other languages. Prior to 22.0.1, 21.2.17, and 20.3.25, an information disclosure vulnerability exists in the @angular/service-worker package of the Angular framework. When the Service Worker fetches assets, it preserves metadata (such as headers) from the original request. However, on cross-origin redirects, the Service Worker fails to strip sensitive headers, violating the Fetch redirect algorithm. This allows a remote attacker to obtain sensitive credentials (e.g., Authorization tokens, Proxy-Authorization credentials, or session cookies) by triggering a cross-origin redirect to an untrusted external origin. This vulnerability is fixed in 22.0.1, 21.2.17, and 20.3.25.

🎖@cveNotify