🎯 PSC Practice Question — Day 1
Simply supported RCC beam, effective span = 6 m.
IS 456:2000 Table 23 പ്രകാരം Minimum Effective Depth?
(A) 240 mm
(B) 300 mm
(C) 375 mm
(D) 420 mm
.
.
.
✅ Answer: (B) 300 mm
📌 Explanation:
IS 456 Table 23 — Basic Span/Depth ratio:
Simply Supported = 20
Minimum depth = Span / 20
= 6000 / 20 = 300 mm
⚠️ Repeat Alert: ഈ type question Kerala PSC AE Civil 2019, 2021 papers-ൽ വന്നിട്ടുണ്ട്!
നിങ്ങൾ ശരിക്കും ഉത്തരം കണ്ടെത്തിയോ? Comment ചെയ്യൂ 👇
— Santhosh | CivilEzy
Simply supported RCC beam, effective span = 6 m.
IS 456:2000 Table 23 പ്രകാരം Minimum Effective Depth?
(A) 240 mm
(B) 300 mm
(C) 375 mm
(D) 420 mm
.
.
.
✅ Answer: (B) 300 mm
📌 Explanation:
IS 456 Table 23 — Basic Span/Depth ratio:
Simply Supported = 20
Minimum depth = Span / 20
= 6000 / 20 = 300 mm
⚠️ Repeat Alert: ഈ type question Kerala PSC AE Civil 2019, 2021 papers-ൽ വന്നിട്ടുണ്ട്!
നിങ്ങൾ ശരിക്കും ഉത്തരം കണ്ടെത്തിയോ? Comment ചെയ്യൂ 👇
— Santhosh | CivilEzy
❤7
🌱 Soil Classification — IS 1498 (USCS)
First letter — Soil type:
G = Gravel | S = Sand
M = Silt | C = Clay
Second letter — Gradation/Plasticity:
W = Well-graded | P = Poorly-graded
H = High plasticity | L = Low plasticity
📌 Examples:
SW = Well-graded Sand
CH = High plasticity Clay (Fat Clay)
CL = Low plasticity Clay (Lean Clay)
🧠 Memory Trick:
CH = "Chechi High" — High plasticity!
CL = "Chechi Low" — Low plasticity!
📐 A-line (Plasticity Chart):
PI = 0.73 (LL − 20)
Above A-line → Clay (C)
Below A-line → Silt (M)
— Santhosh | CivilEzy
First letter — Soil type:
G = Gravel | S = Sand
M = Silt | C = Clay
Second letter — Gradation/Plasticity:
W = Well-graded | P = Poorly-graded
H = High plasticity | L = Low plasticity
📌 Examples:
SW = Well-graded Sand
CH = High plasticity Clay (Fat Clay)
CL = Low plasticity Clay (Lean Clay)
🧠 Memory Trick:
CH = "Chechi High" — High plasticity!
CL = "Chechi Low" — Low plasticity!
📐 A-line (Plasticity Chart):
PI = 0.73 (LL − 20)
Above A-line → Clay (C)
Below A-line → Silt (M)
— Santhosh | CivilEzy
❤16
🎯 PSC Practice Question — Day 2
ഒരു soil sample-ന്:
Liquid Limit (LL) = 45%
Plastic Limit (PL) = 20%
Plasticity Index (PI) = ?
(A) 65
(B) 45
(C) 25
(D) 20
.
.
.
✅ Answer: (C) 25
📌 Formula:
PI = LL − PL
PI = 45 − 20 = 25
🔥 Quick Guide (PI + LL + A-line ചേർത്ത് check ചെയ്യണം):
PI > 35 + LL > 50% → CH (Fat Clay)
PI 7–35 → CL / CI range
PI < 7 → ML (Silt)
📝 Note: PI alone ഒരു quick guide മാത്രം — actual classification-ന് LL value-ഉം A-line position-ഉം കൂടി നോക്കണം.
⚠️ Repeat Alert: 2022 Kerala PSC AE Civil paper-ൽ ഈ exact style വന്നു!
— Santhosh | CivilEzy
ഒരു soil sample-ന്:
Liquid Limit (LL) = 45%
Plastic Limit (PL) = 20%
Plasticity Index (PI) = ?
(A) 65
(B) 45
(C) 25
(D) 20
.
.
.
✅ Answer: (C) 25
📌 Formula:
PI = LL − PL
PI = 45 − 20 = 25
🔥 Quick Guide (PI + LL + A-line ചേർത്ത് check ചെയ്യണം):
PI > 35 + LL > 50% → CH (Fat Clay)
PI 7–35 → CL / CI range
PI < 7 → ML (Silt)
📝 Note: PI alone ഒരു quick guide മാത്രം — actual classification-ന് LL value-ഉം A-line position-ഉം കൂടി നോക്കണം.
⚠️ Repeat Alert: 2022 Kerala PSC AE Civil paper-ൽ ഈ exact style വന്നു!
— Santhosh | CivilEzy
❤10
🌊 Bernoulli's Equation — Civil Engineer-ന്റെ Best Friend!
P/ρg + V²/2g + Z = Constant
📌 Each term:
P/ρg = Pressure Head
V²/2g = Velocity Head
Z = Datum Head
✅ Bernoulli apply ചെയ്യാൻ conditions:
→ Steady flow
→ Incompressible fluid
→ Non-viscous (ideal) fluid
→ Along a streamline
📐 Applications:
• Venturimeter → discharge measurement
• Pitot Tube → velocity measurement
• Orifice Meter → flow measurement
🧠 ഒരിടത്ത് velocity കൂടിയാൽ pressure കുറയും — ഇതാണ് Venturi principle!
⚡ Venturimeter discharge:
Q = Cd × A₁A₂ / √(A₁²−A₂²) × √(2gh)
— Santhosh | CivilEzy
P/ρg + V²/2g + Z = Constant
📌 Each term:
P/ρg = Pressure Head
V²/2g = Velocity Head
Z = Datum Head
✅ Bernoulli apply ചെയ്യാൻ conditions:
→ Steady flow
→ Incompressible fluid
→ Non-viscous (ideal) fluid
→ Along a streamline
📐 Applications:
• Venturimeter → discharge measurement
• Pitot Tube → velocity measurement
• Orifice Meter → flow measurement
🧠 ഒരിടത്ത് velocity കൂടിയാൽ pressure കുറയും — ഇതാണ് Venturi principle!
⚡ Venturimeter discharge:
Q = Cd × A₁A₂ / √(A₁²−A₂²) × √(2gh)
— Santhosh | CivilEzy
❤10
🎯 PSC Practice Question — Day 3
Pipe-ൽ flow velocity = 4 m/s.
Velocity Head = V²/2g = ?
(g = 9.81 m/s²)
(A) 0.408 m
(B) 0.815 m
(C) 1.630 m
(D) 0.204 m
.
.
.
✅ Answer: (B) 0.815 m
📌 Calculation:
V²/2g = (4)² / (2 × 9.81)
= 16 / 19.62
= 0.815 m
🔥 Shortcut:
V = 4 → V² = 16 → ÷ 19.62 ≈ 0.82 m
⚠️ Easy 1 mark — ഈ type calculation almost every PSC paper-ൽ വരും!
ഉത്തരം ശരിയായോ? 👍 Yes / 👎 No
— Santhosh | CivilEzy
Pipe-ൽ flow velocity = 4 m/s.
Velocity Head = V²/2g = ?
(g = 9.81 m/s²)
(A) 0.408 m
(B) 0.815 m
(C) 1.630 m
(D) 0.204 m
.
.
.
✅ Answer: (B) 0.815 m
📌 Calculation:
V²/2g = (4)² / (2 × 9.81)
= 16 / 19.62
= 0.815 m
🔥 Shortcut:
V = 4 → V² = 16 → ÷ 19.62 ≈ 0.82 m
⚠️ Easy 1 mark — ഈ type calculation almost every PSC paper-ൽ വരും!
ഉത്തരം ശരിയായോ? 👍 Yes / 👎 No
— Santhosh | CivilEzy
❤7👍5
🏗️ Moment Distribution Method — Kerala PSC Favourite!
📌 Fixed End Moments:
UDL (w kN/m, span L) → FEM = wL²/12
Central Point Load (W) → FEM = WL/8
📌 Distribution Factor:
DF = K_member / ΣK_joint
Stiffness K:
Far end FIXED → K = 4EI/L
Far end PINNED → K = 3EI/L
📌 Carry Over Factor:
Far end Fixed → 0.5
Far end Pinned/Free → 0
🧠 Sign Convention:
Clockwise = Positive (+)
Anti-clockwise = Negative (−)
🎯 PSC Tip:
Sum of DF at any joint = 1.0 (always!)
— Santhosh | CivilEzy
📌 Fixed End Moments:
UDL (w kN/m, span L) → FEM = wL²/12
Central Point Load (W) → FEM = WL/8
📌 Distribution Factor:
DF = K_member / ΣK_joint
Stiffness K:
Far end FIXED → K = 4EI/L
Far end PINNED → K = 3EI/L
📌 Carry Over Factor:
Far end Fixed → 0.5
Far end Pinned/Free → 0
🧠 Sign Convention:
Clockwise = Positive (+)
Anti-clockwise = Negative (−)
🎯 PSC Tip:
Sum of DF at any joint = 1.0 (always!)
— Santhosh | CivilEzy
🎯 PSC Practice Question — Day 4
Fixed beam AB, span = 6 m.
UDL = 10 kN/m throughout.
Fixed End Moment at A = ?
(A) 60 kN·m
(B) 45 kN·m
(C) 30 kN·m
(D) 90 kN·m
.
.
.
✅ Answer: (C) 30 kN·m
📌 Formula:
FEM = wL²/12
= 10 × (6)² / 12
= 10 × 36 / 12
= 30 kN·m
⚠️ Exam Alert: 2020 Kerala PSC AE Civil paper-ൽ ഇതേ type question directly വന്നു!
More solved examples → t.me/civilezy_psc
— Santhosh | CivilEzy
Fixed beam AB, span = 6 m.
UDL = 10 kN/m throughout.
Fixed End Moment at A = ?
(A) 60 kN·m
(B) 45 kN·m
(C) 30 kN·m
(D) 90 kN·m
.
.
.
✅ Answer: (C) 30 kN·m
📌 Formula:
FEM = wL²/12
= 10 × (6)² / 12
= 10 × 36 / 12
= 30 kN·m
⚠️ Exam Alert: 2020 Kerala PSC AE Civil paper-ൽ ഇതേ type question directly വന്നു!
More solved examples → t.me/civilezy_psc
— Santhosh | CivilEzy
Telegram
CivilEzy — Kerala PSC Civil Engineering
Kerala PSC AE Civil / Overseer / Draftsman aspirants-നായി daily concept capsules, practice MCQs, PYQ analysis. Free channel by CivilEzy. Web: www.civilezy.in
🛣️ Highway Design — IRC Classification
Road Type → Design Speed:
NH (National Highway) → 100 kmph
SH (State Highway) → 80 kmph
MDR (Major District Road) → 60 kmph
ODR (Other District Road) → 50 kmph
VR (Village Road) → 40 kmph
🧠 Memory: "Never Stop MDR On Village"
= NH, SH, MDR, ODR, VR
📐 Horizontal Curve (IRC:38):
R = V² / [127(e + f)]
e = max 0.07 (plain terrain)
f = 0.15 (highways)
📌 Sight Distance order:
SSD < ISD < OSD < HSD
🔥 Kerala PSC Must-Know:
Ruling gradient NH = 3.3% (plain terrain)
Limiting gradient = 5%
— Santhosh | CivilEzy
Road Type → Design Speed:
NH (National Highway) → 100 kmph
SH (State Highway) → 80 kmph
MDR (Major District Road) → 60 kmph
ODR (Other District Road) → 50 kmph
VR (Village Road) → 40 kmph
🧠 Memory: "Never Stop MDR On Village"
= NH, SH, MDR, ODR, VR
📐 Horizontal Curve (IRC:38):
R = V² / [127(e + f)]
e = max 0.07 (plain terrain)
f = 0.15 (highways)
📌 Sight Distance order:
SSD < ISD < OSD < HSD
🔥 Kerala PSC Must-Know:
Ruling gradient NH = 3.3% (plain terrain)
Limiting gradient = 5%
— Santhosh | CivilEzy
🎯 PSC Practice Question — Day 5
IRC:58 പ്രകാരം CC Pavement-ലെ Expansion Joint spacing = ?
(A) 50 m
(B) 140 m
(C) 20 m
(D) 30 m
.
.
.
✅ Answer: (B) 140 m
📌 IRC:58 Joint Spacing:
Expansion Joint → 140 m
Contraction Joint → 4.5 m (with dowel bars)
🧠 Memory:
140 = "One Forty" = Expansion
4.5 = "Four point Five" = Contraction
⚠️ Repeat Alert: Almost every Kerala PSC paper-ൽ ഈ question വരും!
Comment: Rigid vs Flexible Pavement difference അടുത്ത post-ൽ explain ചെയ്യട്ടെ? 👇
— Santhosh | CivilEzy
IRC:58 പ്രകാരം CC Pavement-ലെ Expansion Joint spacing = ?
(A) 50 m
(B) 140 m
(C) 20 m
(D) 30 m
.
.
.
✅ Answer: (B) 140 m
📌 IRC:58 Joint Spacing:
Expansion Joint → 140 m
Contraction Joint → 4.5 m (with dowel bars)
🧠 Memory:
140 = "One Forty" = Expansion
4.5 = "Four point Five" = Contraction
⚠️ Repeat Alert: Almost every Kerala PSC paper-ൽ ഈ question വരും!
Comment: Rigid vs Flexible Pavement difference അടുത്ത post-ൽ explain ചെയ്യട്ടെ? 👇
— Santhosh | CivilEzy
👍9
💧 Water Treatment Sequence — ഒരിക്കൽ ഓർത്താൽ മതി!
Screening
↓
Aeration
↓
Plain Sedimentation
↓
Coagulation & Flocculation
(Alum = Al₂(SO₄)₃)
↓
Sedimentation (Clariflocculator)
↓
Filtration (Rapid Sand Filter)
↓
Disinfection (Chlorination)
↓
Distribution
📌 IS 10500 Key Values:
Turbidity → < 1 NTU (desirable), < 5 NTU (permissible)
pH → 6.5 – 8.5
Residual Cl₂ → min 0.2 mg/L
📐 BOD vs COD:
COD > BOD > Theoretical OD (always)
— Santhosh | CivilEzy
Screening
↓
Aeration
↓
Plain Sedimentation
↓
Coagulation & Flocculation
(Alum = Al₂(SO₄)₃)
↓
Sedimentation (Clariflocculator)
↓
Filtration (Rapid Sand Filter)
↓
Disinfection (Chlorination)
↓
Distribution
📌 IS 10500 Key Values:
Turbidity → < 1 NTU (desirable), < 5 NTU (permissible)
pH → 6.5 – 8.5
Residual Cl₂ → min 0.2 mg/L
📐 BOD vs COD:
COD > BOD > Theoretical OD (always)
— Santhosh | CivilEzy
👍5❤2
🎯 PSC Practice Question — Day 6
Slow Sand Filter vs Rapid Sand Filter — Filtration rate ratio?
(A) ≈ 10 : 1
(B) ≈ 50 : 1
(C) ≈ 100 : 1
(D) ≈ 5 : 1
.
.
.
✅ Answer: (B) ≈ 50 : 1
📌 Filtration Rates:
Slow Sand Filter → 0.1 – 0.4 m/h
Rapid Sand Filter → 5 – 15 m/h
Ratio ≈ 15 / 0.3 ≈ 50 times faster
Key Difference:
SSF → Biological action (Schmutzdecke layer)
RSF → Physical-chemical, needs Coagulation first
⚠️ Repeat Alert: 2021, 2023 PSC papers-ൽ directly ചോദിച്ചു!
നാളെ Final Day: Concrete Technology 🏗️
— Santhosh | CivilEzy
Slow Sand Filter vs Rapid Sand Filter — Filtration rate ratio?
(A) ≈ 10 : 1
(B) ≈ 50 : 1
(C) ≈ 100 : 1
(D) ≈ 5 : 1
.
.
.
✅ Answer: (B) ≈ 50 : 1
📌 Filtration Rates:
Slow Sand Filter → 0.1 – 0.4 m/h
Rapid Sand Filter → 5 – 15 m/h
Ratio ≈ 15 / 0.3 ≈ 50 times faster
Key Difference:
SSF → Biological action (Schmutzdecke layer)
RSF → Physical-chemical, needs Coagulation first
⚠️ Repeat Alert: 2021, 2023 PSC papers-ൽ directly ചോദിച്ചു!
നാളെ Final Day: Concrete Technology 🏗️
— Santhosh | CivilEzy
❤2👍1
🏗️ Concrete Mix Design — IS 456:2000
Grades & Characteristic Strength:
M15 → 15 N/mm² (PCC only)
M20 → 20 N/mm² (minimum for RCC)
M25 → 25 N/mm²
M30 → 30 N/mm²
✅ PSC Must-Know:
M20 = Minimum grade for RCC structures
M15 = Plain Cement Concrete only
📌 W/C Ratio (IS 456 Table 5):
Mild → max 0.55
Moderate → max 0.50
Severe → max 0.45
Very Severe → max 0.45
Extreme → max 0.40
W/C കൂടിയാൽ:
Workability ↑ | Strength ↓ | Durability ↓
🧠 Slump Test:
Stiff → 0–25 mm
Medium → 50–100 mm
Flowing → 100–175 mm
— Santhosh | CivilEzy
Grades & Characteristic Strength:
M15 → 15 N/mm² (PCC only)
M20 → 20 N/mm² (minimum for RCC)
M25 → 25 N/mm²
M30 → 30 N/mm²
✅ PSC Must-Know:
M20 = Minimum grade for RCC structures
M15 = Plain Cement Concrete only
📌 W/C Ratio (IS 456 Table 5):
Mild → max 0.55
Moderate → max 0.50
Severe → max 0.45
Very Severe → max 0.45
Extreme → max 0.40
W/C കൂടിയാൽ:
Workability ↑ | Strength ↓ | Durability ↓
🧠 Slump Test:
Stiff → 0–25 mm
Medium → 50–100 mm
Flowing → 100–175 mm
— Santhosh | CivilEzy
📋 Week 1 — Quick Revision Summary
ഈ ആഴ്ച നാം പഠിച്ചത് — ഒരു quick revision! 🔥
✅ Day 1 — RCC Design (IS 456:2000):Minimum concrete grade for RCC = M20Simply Supported L/d = 20 | Continuous = 26 | Cantilever = 7W/C ratio (Moderate) = 0.50 | (Severe) = 0.45Min steel in beam = 0.85/fy | Max = 4%
✅ Day 2 — Soil Mechanics (IS 1498):PI = LL − PLA-line: PI = 0.73(LL − 20)CH = High plasticity clay | CL = Low plasticity clayAbove A-line → Clay (C) | Below → Silt (M)
✅ Day 3 — Fluid Mechanics:Bernoulli: P/ρg + V²/2g + Z = ConstantVenturimeter → Discharge | Pitot tube → VelocityV²/2g = Velocity Head
✅ Day 4 — Structural Analysis (MDM):UDL fixed beam FEM = wL²/12Central point load FEM = WL/8SS beam UDL Max BM = wL²/8Carry over factor = 0.5 (far fixed end)
✅ Day 5 — Highway Engineering (IRC):NH plain terrain design speed = 100 kmphS
tandard axle load = 80 kN
Flexible pavement layers: Subgrade → GSB → WMM → DBM → BCExpansion joint spacing = 140 m (IRC:58)
✅ Day 6 — Steel Structures (IS 800:2007):I
S 800:2007 = Limit State Method
Fe415 → fy = 415 N/mm² | Fe250 → 250 N/mm²M
in pitch = 2.5 × bolt dia
Min edge distance = 1.7 × hole dia
🎯 നാളെ Sunday 8:00 PM — Week 1 Live Exam!20 Questions | 20 Minutes | Kerala Rank List 🏆
ഒരു round കൂടി revision ചെയ്യൂ — All the best! 💪— Santhosh | CivilEzy
t.me/civilezy_psc❤5
🏆 CivilEzy — Week 1 Live Exam
നാളെ Sunday March 29 — 8:00 PM! ⏰
📚 Exam Topics:✅ RCC Design — IS 456:2000✅ Soil Mechanics — IS 1498 (USCS)✅ Fluid Mechanics — Bernoulli's Theorem✅ Structural Analysis — MDM & SFD/BMD✅ Highway Engineering — IRC Standards✅ Steel Structures — IS 800:2007
🎯 20 Questions | 20 Minutes⏱ 60 seconds per question📊 Kerala Rank List — live after exam🔁 PYQ flags in Monday answer key
ഇന്ന് രാത്രി ഒരു revision കൂടി നടത്തൂ!നാളെ 8 PM-ന് ready ആയിരിക്കൂ 💪
— Santhosh | CivilEzyt.me/civilezy_psc❤1
🎯 PSC Practice Question — Day 7
IS 269 പ്രകാരം OPC-ന്റെ Initial Setting Time minimum = ?
(A) 15 minutes
(B) 30 minutes
(C) 45 minutes
(D) 60 minutes
.
.
.
✅ Answer: (B) 30 minutes
📌 IS 269 Setting Times:
Initial Setting Time → min 30 minutes
Final Setting Time → max 600 minutes (10 hrs)
🧠 Memory:
"30 minuteൽ start, 10 hourൽ finish"
⚠️ OPC vs PPC:
Initial ST same (30 min) — but PPC has slower strength gain.
🔥 Week 1 complete! Full mock tests → t.me/civilezy_psc
Share ചെയ്യൂ — ഒരു friend-നെ tag ചെയ്യൂ! 👇
— Santhosh | CivilEzy
IS 269 പ്രകാരം OPC-ന്റെ Initial Setting Time minimum = ?
(A) 15 minutes
(B) 30 minutes
(C) 45 minutes
(D) 60 minutes
.
.
.
✅ Answer: (B) 30 minutes
📌 IS 269 Setting Times:
Initial Setting Time → min 30 minutes
Final Setting Time → max 600 minutes (10 hrs)
🧠 Memory:
"30 minuteൽ start, 10 hourൽ finish"
⚠️ OPC vs PPC:
Initial ST same (30 min) — but PPC has slower strength gain.
🔥 Week 1 complete! Full mock tests → t.me/civilezy_psc
Share ചെയ്യൂ — ഒരു friend-നെ tag ചെയ്യൂ! 👇
— Santhosh | CivilEzy
Telegram
CivilEzy — Kerala PSC Civil Engineering
Kerala PSC AE Civil / Overseer / Draftsman aspirants-നായി daily concept capsules, practice MCQs, PYQ analysis. Free channel by CivilEzy. Web: www.civilezy.in
Week 1 Exam conducted on tomorrow 8 pm
📐 RCC Beam Design — IS 456:2000
Singly Reinforced Beam — Ultimate Moment of Resistance:
Mu = 0.87 fy Ast (d − 0.42 xu)
📌 Limiting Neutral Axis Depth (xu,max/d):Fe 250 → 0.53Fe 415 → 0.48Fe 500 → 0.46Fe 550 → 0.44 ← Bonus: Recent PSC exams asking this!
✅ Under-reinforced beam:xu < xu,max → Steel yields first → Ductile failure ✓ (Preferred!)
❌ Over-reinforced beam:xu > xu,max → Concrete crushes first → Brittle failure ✗
📌 Limiting Moment of Resistance:Mu,lim = 0.36 fck b xu,max (d − 0.42 xu,max)🧠 Memory Trick:
Higher fy → Lower xu,max/dFe 250=0.53 | Fe 415=0.48 | Fe 500=0.46 | Fe 550=0.44(Value keeps dropping as strength increases!)
⚠️ PSC Alert: Under-reinforced vs Over-reinforced failure mode — AE Civil repeat topic!— Santhosh | CivilEzy
t.me/civilezy_psc❤1
🎯 PSC Practice Question — Week 2 Day 1
As per IS 456:2000, the limiting value of xu,max/d for Fe415 steel is?
(A) 0.53(B) 0.46(C) 0.48(D) 0.60.
.
.
✅ Answer: (C) 0.48
📌 Explanation:xu,max/d depends on steel grade:F
e250 → 0.53
Fe415 → 0.48
Fe500 → 0.46
Higher fy → Lower xu,max/dHigher strength steel = more ductile = NA shifts up🧠 Quick memory:
Fe415 → 0.48 — "4-1-5 gives 0.4-8"
⚠️ Repeat Alert: ഈ exact values Kerala PSC AE Civil 2020 paper-ൽ directly വന്നു!
ഉത്തരം ശരിയായോ? Comment ചെയ്യൂ 👇
— Santhosh | CivilEzy❤2👍1