In this example we look at a complex piping system of a mineral processing plant that included following non standard fittings:
✅ Crotch plated 45 degree lateral tees
✅ Crotch plated 90 degree double tees or crosses
✅ Crotch plated 45 degree lateral tees
✅ Crotch plated 90 degree double tees or crosses
The above fittings can have many variants, like equal, unequal, non reinforced, pad reinforced or integrally reinforced. We come across such fittings in existing chemical plants and piping systems which often require flexibility analysis in order to check compliance with design codes. A knowledge of their SIFs is a pre-requisite to flexibility analysis. Piping Engineers have been using empirical rules to get over this difficulty, often leading to uncertain and/or over designed systems.
History
Various attempts were made in the past to redesign this piping system but none could proceed to completion as a suitable methodology to assess the SIFs of these non standard fittings was not available.
Three previous studies proposed major modifications. These were unacceptable as they proposed major changes to the geometry of the pipework. Client was insisting on examining options that did not include major geometrical changes to the piping system. Clients argument was that the existing piping system has survived nearly 40 years and piping engineers should be able to find an explanation to this conundrum.
Various attempts were made in the past to redesign this piping system but none could proceed to completion as a suitable methodology to assess the SIFs of these non standard fittings was not available.
Three previous studies proposed major modifications. These were unacceptable as they proposed major changes to the geometry of the pipework. Client was insisting on examining options that did not include major geometrical changes to the piping system. Clients argument was that the existing piping system has survived nearly 40 years and piping engineers should be able to find an explanation to this conundrum.
With the increasing acceptance of Finite Element Analysis (FEA) as an analysis tool in industry, it was suggested that an investigation be undertaken to study the use of FEA to investigate the stresses in these fittings and to interpret the results in the light of the design intent of ASME B31.3.
These fittings have been used over 50 years in piping/ducting systems and they were around when A. R. C. Markl’s did his testing program in 1950’s. Some crotch plated branch fittings are shown in the Piping Handbook ‘Design of Piping Systems’ published in the 1950’s by M. W. Kellogg Ltd. This handbook was considered an authoritative source of information for the piping engineer of that era. However, these crotch plated branch fittings were not part of Markl’s fatigue testing programme, thus missed out of being part of ASME B 31 series SIF definition.
Conclusion
SIFs calculated using the above methodology are acceptable to be used in flexibility analysis in design, in accordance with ASME B31.3.
SIFs calculated using the above methodology are acceptable to be used in flexibility analysis in design, in accordance with ASME B31.3.
This media is not supported in your browser
VIEW IN TELEGRAM
Safety valve ope
Answer:
Use the same modeling technique as used in the following AutoPIPE help section:
Help > Contents> Contents Tab> Modeling Approaches> Modeling Approaches> Vessels
In this case you will need to provide the DX, DY, and DZ. to both Pipe #1 and Pipe #2 connection locations.
Procedure:
1. Move cursor to header pipe node point (ex. A05)
2. Convert Node into a Tee
3. Insert new branch segment (ex. B) on tee (ex. from A05), extend new piping to Pipe #1 connection location (ex. B01), should be on the outside surface of the header pipe.
4. Insert additional node points on segment piping as needed.
5. Select the piping inside of the header pipe (ex. A05 to B01). Insert> Rigid Options Over Range> Include Weight - OFF, Include Thermal Expansion - ON. press OK button to close dialog screen.
6. Select the header node point, Insert Xtra Data> Joint type and user SIF = user defined, "Override all SIF's at this point" - Checked ON.
Use the same modeling technique as used in the following AutoPIPE help section:
Help > Contents> Contents Tab> Modeling Approaches> Modeling Approaches> Vessels
In this case you will need to provide the DX, DY, and DZ. to both Pipe #1 and Pipe #2 connection locations.
Procedure:
1. Move cursor to header pipe node point (ex. A05)
2. Convert Node into a Tee
3. Insert new branch segment (ex. B) on tee (ex. from A05), extend new piping to Pipe #1 connection location (ex. B01), should be on the outside surface of the header pipe.
4. Insert additional node points on segment piping as needed.
5. Select the piping inside of the header pipe (ex. A05 to B01). Insert> Rigid Options Over Range> Include Weight - OFF, Include Thermal Expansion - ON. press OK button to close dialog screen.
6. Select the header node point, Insert Xtra Data> Joint type and user SIF = user defined, "Override all SIF's at this point" - Checked ON.
7. Select node point on surface of pipe where the connection is made, (ex. B01), Insert Xtra Data> Joint type and user SIF, enter the correct SIF for the connection point, and again, "Override all SIF's at this point" - Checked ON.
8. Repeat steps #3 - #7 for each additional pipe to be connected at the same location (ex. A05).
9. Move to next header node point and repeat steps #1 - #8 for all points allong the header to have more that 1 pipe connection that is offset from the normal position.
8. Repeat steps #3 - #7 for each additional pipe to be connected at the same location (ex. A05).
9. Move to next header node point and repeat steps #1 - #8 for all points allong the header to have more that 1 pipe connection that is offset from the normal position.