ESE 2021 transcript
Smita nagaraj ma'am panel
Date:03/03/2022,
Afternoon session
Duration:30-35min
Chairman: You are selected as assistant engineer in cgpsc,so why you want to leave comfort zone for ese?
2.What is your preference of department in ese?
3.We often see lot of seepage in old government buildings,what is the reason?
4.If water cannot be metered,what could be the causes and remedial measures?
5.Examples of success of public health engineering department and shortcomings.
Member1:
1.What is cavity found in gas pipelines and the reason behind it?
2.Why maximum spacing of piles in is code has been specified?
3.What percentage of earth pressure is carried by geogrids in retaining wall?
4.Why compaction is difficult in sand?
5.How we measure relative density of sand?
6.Why is density same in case of dry and saturated same?
Member 2:
1.If iron is present in soil,what will be the properties of this soil?
2.If we have to carry water from a low level to high level ,commonly used?
3.What is measurement book?
4.What is inventory management?
5.Why and how rate analysis is done?
6.How is steel measurement done
7.Classification of doors
8.Approx how much steel and concrete would have been used in the construction of this room?
9.Rough rubble masonry and ashlar masonary
10.Effect of shear on masonary wall
Memeber 3:
1.Difference between PERT and CPM?
2.What is optimum duration
3.Explain crashing curve
4.Difference between rate analysis and SOR?
5.Types of contracts
6.Green building
7.load combinations according to IS 456
8.Traps used in kitchen,and location of these
9.Water distribution network,function of ferrule?
10.What is single and double stacking system?
11.Characteristic strength.
Some other terms related to environment and construction management,that i had heard for the first time.
Smita nagaraj ma'am panel
Date:03/03/2022,
Afternoon session
Duration:30-35min
Chairman: You are selected as assistant engineer in cgpsc,so why you want to leave comfort zone for ese?
2.What is your preference of department in ese?
3.We often see lot of seepage in old government buildings,what is the reason?
4.If water cannot be metered,what could be the causes and remedial measures?
5.Examples of success of public health engineering department and shortcomings.
Member1:
1.What is cavity found in gas pipelines and the reason behind it?
2.Why maximum spacing of piles in is code has been specified?
3.What percentage of earth pressure is carried by geogrids in retaining wall?
4.Why compaction is difficult in sand?
5.How we measure relative density of sand?
6.Why is density same in case of dry and saturated same?
Member 2:
1.If iron is present in soil,what will be the properties of this soil?
2.If we have to carry water from a low level to high level ,commonly used?
3.What is measurement book?
4.What is inventory management?
5.Why and how rate analysis is done?
6.How is steel measurement done
7.Classification of doors
8.Approx how much steel and concrete would have been used in the construction of this room?
9.Rough rubble masonry and ashlar masonary
10.Effect of shear on masonary wall
Memeber 3:
1.Difference between PERT and CPM?
2.What is optimum duration
3.Explain crashing curve
4.Difference between rate analysis and SOR?
5.Types of contracts
6.Green building
7.load combinations according to IS 456
8.Traps used in kitchen,and location of these
9.Water distribution network,function of ferrule?
10.What is single and double stacking system?
11.Characteristic strength.
Some other terms related to environment and construction management,that i had heard for the first time.
Date-03/03/2022.
Morning session
Currently undergoing training at IOCL
Chairperson-Soni sir
M1,M2-Male.M3-Female
Ch-
1.You are from village, what is the population?
2.Your hobbies are playing and watching cricket.Do you still watch the cricket?What do you do?
3.As a civil engineer what is the advantage you take from others while bowling?
4.What is Bernoulli principal?
5.What is the length of bat, wicket?
6.what is the length of pitch?
8.How many time you have travelled by air?
9.What do you see the yellow mark?
10.What is white mark portion called?
11.Length of Runway?
12.What is the material used in runway?
13.What is harbour?
14.What is dock?
15.what the place called where ship gets maintaince?
16.How does aeroplane gets navigation?
20.What is light house?
21.You are in Iocl,In which division are you in?What are the product of Iocl?
22.How does finished product supplied to market?
M1.
1.What is Archimedes principal?
2.What is drainage gallery?
3.What is pheriatic line?
4.Draw component of earthen dam
5.What is the property of parabola
M2.
1.What is your favourite subject?
2.How do you calculate stress at any point in soil
3.What is the formula given by Bossensq for stress calculation?
4.Suppose your top soil is weak.How to you increase its bearing capacity?
M3.
1.How the water is supplied to your house?
2.Suppose you have a 3 floor building and a tank on it.What should be the Pump power in hp?
3.What are the type of pump?
Morning session
Currently undergoing training at IOCL
Chairperson-Soni sir
M1,M2-Male.M3-Female
Ch-
1.You are from village, what is the population?
2.Your hobbies are playing and watching cricket.Do you still watch the cricket?What do you do?
3.As a civil engineer what is the advantage you take from others while bowling?
4.What is Bernoulli principal?
5.What is the length of bat, wicket?
6.what is the length of pitch?
8.How many time you have travelled by air?
9.What do you see the yellow mark?
10.What is white mark portion called?
11.Length of Runway?
12.What is the material used in runway?
13.What is harbour?
14.What is dock?
15.what the place called where ship gets maintaince?
16.How does aeroplane gets navigation?
20.What is light house?
21.You are in Iocl,In which division are you in?What are the product of Iocl?
22.How does finished product supplied to market?
M1.
1.What is Archimedes principal?
2.What is drainage gallery?
3.What is pheriatic line?
4.Draw component of earthen dam
5.What is the property of parabola
M2.
1.What is your favourite subject?
2.How do you calculate stress at any point in soil
3.What is the formula given by Bossensq for stress calculation?
4.Suppose your top soil is weak.How to you increase its bearing capacity?
M3.
1.How the water is supplied to your house?
2.Suppose you have a 3 floor building and a tank on it.What should be the Pump power in hp?
3.What are the type of pump?
Ese 2021
Panel- manoj soni
Date - 03/03 afternoon
Background- delhite, iitr mtech geotechnical
Chairman
1- you are a delhite, how do you see delhi as a city.
2- which city in the world will you prefer to live your whole life if given a choice.
3- tell me 5 applications of geotechnical engineering
4. We have many highways under construction, what is the goetechnical aspect of providing trees on highways.
5- cp has old buildings, we have constructed tunnel underground, how do you find the strength of the soil and foundation.
6- what is the unit of bearing capacity.
Member 1-
1. What is famous in roorkee.
2. When was civil engg department established in iitr.
3. Have you heard of __. It is famous in Roorkee for civil engineering aspect.
4. What is shotcreting.
5. Where do we use and why?
6. What is grouting.
7. Where do we use grouting.
8. What is slope stabilization.
Member 2-
1. What is aqueduct
2. How to you design the aqueduct
3. How do you take width and depth of aqueduct part
4. Difference between barrage and a dam
5. How to provide safety against water in soil in embankment and for foundation
6. Something he asked for which i said sheet pile wall.
7. How to decide depth of sheet pile wall
8. Write the formula of hydraulic gradient
9. I said hydraulic gradient.
M3 ( madam thi,mask k andar kya keh gyi aadha samjh nhi aya)
1- factors affecting permeability
2. Factors not affecting permeability
3. What is ICT
4. Prime minister said something lately, what that in regard of ICT
5. Draw a canal crosss section
6. What is cutting and what is filling, show in that diagram
7. Why do we try to make cutting equal to filling
8. Whta is there is only cutting, will that become uneconomical
9. What is the importance of river bank
10. How do you decide canal alignment
11. What is ____? ( I said sorry ma'am not heard of it)
12. Some questions on canal bank, lining vegative cover like that.
Chairman- khatam tata goodbye.
Panel- manoj soni
Date - 03/03 afternoon
Background- delhite, iitr mtech geotechnical
Chairman
1- you are a delhite, how do you see delhi as a city.
2- which city in the world will you prefer to live your whole life if given a choice.
3- tell me 5 applications of geotechnical engineering
4. We have many highways under construction, what is the goetechnical aspect of providing trees on highways.
5- cp has old buildings, we have constructed tunnel underground, how do you find the strength of the soil and foundation.
6- what is the unit of bearing capacity.
Member 1-
1. What is famous in roorkee.
2. When was civil engg department established in iitr.
3. Have you heard of __. It is famous in Roorkee for civil engineering aspect.
4. What is shotcreting.
5. Where do we use and why?
6. What is grouting.
7. Where do we use grouting.
8. What is slope stabilization.
Member 2-
1. What is aqueduct
2. How to you design the aqueduct
3. How do you take width and depth of aqueduct part
4. Difference between barrage and a dam
5. How to provide safety against water in soil in embankment and for foundation
6. Something he asked for which i said sheet pile wall.
7. How to decide depth of sheet pile wall
8. Write the formula of hydraulic gradient
9. I said hydraulic gradient.
M3 ( madam thi,mask k andar kya keh gyi aadha samjh nhi aya)
1- factors affecting permeability
2. Factors not affecting permeability
3. What is ICT
4. Prime minister said something lately, what that in regard of ICT
5. Draw a canal crosss section
6. What is cutting and what is filling, show in that diagram
7. Why do we try to make cutting equal to filling
8. Whta is there is only cutting, will that become uneconomical
9. What is the importance of river bank
10. How do you decide canal alignment
11. What is ____? ( I said sorry ma'am not heard of it)
12. Some questions on canal bank, lining vegative cover like that.
Chairman- khatam tata goodbye.
👍1
Date : 04/03/2022
Interview Duration: 25mins
Chairman: Smirta Nagraj Mam
Background: BTech 2020 passout , AMU
currently pursuing MTech Environmental engineering 1st. year
CHAIRPERSON :-
1. What are you doing now (as I had not mentioned about MTech in my DAF)
2."I observe a lot of noise from upstairs , so how can it be prevented"
I answered sound insulation medium and cavity walls
3. What are cavity walls and insulation walls, how are they made.
4 . You mentioned abestos, what is the problem with using asbestos
5. What have you planned for your MTech thesis project
(Told about air quality modelling)
6. Which pollutant you will monitor (told about AQI ) and how can it help in pollution abatement
7. Why Delhi has frequent problem of pollution, measures to cater the same
8. How solid waste is treated at AMU ,Major sources of pollutants from Aligarh city.
MEMBER 1 :
1.Can you give me an example of major structure which do not require earthquake consideration.
2.which seismic waves cannot travel in liquid medium
3. Real example of carbon sequestration .
4.compositon of asbestos.
5. Why do we limit value of skin friction resistance in pile foundation in Sandy soil
5. Difference between bulk modulus and modulus of rigidity
MEMBER 2 :
1. What is lintel?
2. Provisions for lintel embedment value
3. What is Sill level
4. What is dado and skirting
5. What are types of tender
6. Why after decreasing time beyond optimum time project cost increases even though manpower and materials requirements remains the same
7. Consideration to be taken while doing work in cold wheather conditions
8. Pointing to the main door, which type of door it is ?
Member 3 :—
1. What is a sound vibration and condition in which it becomes dangerous for a structure
2. How vibrations are minimised in a bridges and flyovers? (Told Elastomeric bearings)
3. Compositon of Elastomeric bearings
4. Pointing to two windows , what is the main difference between them ,in terms of its classification
5. What is aspect ratio in slab and what will be the effect if we provide same reforcement in 1 way slab as we provide for 2 way slab.
Interview Duration: 25mins
Chairman: Smirta Nagraj Mam
Background: BTech 2020 passout , AMU
currently pursuing MTech Environmental engineering 1st. year
CHAIRPERSON :-
1. What are you doing now (as I had not mentioned about MTech in my DAF)
2."I observe a lot of noise from upstairs , so how can it be prevented"
I answered sound insulation medium and cavity walls
3. What are cavity walls and insulation walls, how are they made.
4 . You mentioned abestos, what is the problem with using asbestos
5. What have you planned for your MTech thesis project
(Told about air quality modelling)
6. Which pollutant you will monitor (told about AQI ) and how can it help in pollution abatement
7. Why Delhi has frequent problem of pollution, measures to cater the same
8. How solid waste is treated at AMU ,Major sources of pollutants from Aligarh city.
MEMBER 1 :
1.Can you give me an example of major structure which do not require earthquake consideration.
2.which seismic waves cannot travel in liquid medium
3. Real example of carbon sequestration .
4.compositon of asbestos.
5. Why do we limit value of skin friction resistance in pile foundation in Sandy soil
5. Difference between bulk modulus and modulus of rigidity
MEMBER 2 :
1. What is lintel?
2. Provisions for lintel embedment value
3. What is Sill level
4. What is dado and skirting
5. What are types of tender
6. Why after decreasing time beyond optimum time project cost increases even though manpower and materials requirements remains the same
7. Consideration to be taken while doing work in cold wheather conditions
8. Pointing to the main door, which type of door it is ?
Member 3 :—
1. What is a sound vibration and condition in which it becomes dangerous for a structure
2. How vibrations are minimised in a bridges and flyovers? (Told Elastomeric bearings)
3. Compositon of Elastomeric bearings
4. Pointing to two windows , what is the main difference between them ,in terms of its classification
5. What is aspect ratio in slab and what will be the effect if we provide same reforcement in 1 way slab as we provide for 2 way slab.
ESE 2021
Panel- Manoj soni
Date - 03/03 afternoon
Background- Delhite, IITR Mtech geotechnical
Chairman
1- you are a delhite, how do you see delhi as a city.
2- which city in the world will you prefer to live your whole life if given a choice.
3- tell me 5 applications of geotechnical engineering
4. We have many highways under construction, what is the geotechnical aspect of providing trees on highways.
5- cp has old buildings, we have constructed tunnel underground, how do you find the strength of the soil and foundation.
6- what is the unit of bearing capacity.
Member 1-
1. What is famous in roorkee.
2. When was civil engg department established in iitr.
3. Have you heard of __. It is famous in Roorkee for civil engineering aspect.
4. What is shotcreting.
5. Where do we use and why?
6. What is grouting.
7. Where do we use grouting.
8. What is slope stabilization.
Member 2-
1. What is aqueduct
2. How to you design the aqueduct
3. How do you take width and depth of aqueduct part
4. Difference between barrage and a dam
5. How to provide safety against water in soil in embankment and for foundation
6. Something he asked for which i said sheet pile wall.
7. How to decide depth of sheet pile wall
8. Write the formula of hydraulic gradient
9. I said hydraulic gradient.
M3 ( madam thi,mask k andar kya keh gyi aadha samjh nhi aya)
1- factors affecting permeability
2. Factors not affecting permeability
3. What is ICT
4. Prime minister said something lately, what that in regard of ICT
5. Draw a canal cross section
6. What is cutting and what is filling, show in that diagram
7. Why do we try to make cutting equal to filling
8. What is there is only cutting, will that become uneconomical
9. What is the importance of river bank
10. How do you decide canal alignment
11. What is ____? ( I said sorry ma'am not heard of it)
12. Some questions on canal bank, lining vegitative cover like that.
Chairman- khatam tata goodbye.
Panel- Manoj soni
Date - 03/03 afternoon
Background- Delhite, IITR Mtech geotechnical
Chairman
1- you are a delhite, how do you see delhi as a city.
2- which city in the world will you prefer to live your whole life if given a choice.
3- tell me 5 applications of geotechnical engineering
4. We have many highways under construction, what is the geotechnical aspect of providing trees on highways.
5- cp has old buildings, we have constructed tunnel underground, how do you find the strength of the soil and foundation.
6- what is the unit of bearing capacity.
Member 1-
1. What is famous in roorkee.
2. When was civil engg department established in iitr.
3. Have you heard of __. It is famous in Roorkee for civil engineering aspect.
4. What is shotcreting.
5. Where do we use and why?
6. What is grouting.
7. Where do we use grouting.
8. What is slope stabilization.
Member 2-
1. What is aqueduct
2. How to you design the aqueduct
3. How do you take width and depth of aqueduct part
4. Difference between barrage and a dam
5. How to provide safety against water in soil in embankment and for foundation
6. Something he asked for which i said sheet pile wall.
7. How to decide depth of sheet pile wall
8. Write the formula of hydraulic gradient
9. I said hydraulic gradient.
M3 ( madam thi,mask k andar kya keh gyi aadha samjh nhi aya)
1- factors affecting permeability
2. Factors not affecting permeability
3. What is ICT
4. Prime minister said something lately, what that in regard of ICT
5. Draw a canal cross section
6. What is cutting and what is filling, show in that diagram
7. Why do we try to make cutting equal to filling
8. What is there is only cutting, will that become uneconomical
9. What is the importance of river bank
10. How do you decide canal alignment
11. What is ____? ( I said sorry ma'am not heard of it)
12. Some questions on canal bank, lining vegitative cover like that.
Chairman- khatam tata goodbye.
ESE 2021 interview
Panel : Chairperson +3 members
Chairperson- Sujata mehta
1 female , 2 males in tech members
Date - 02/03/2022 ,time 11.26 am
Duration - 24 minutes
Background -NIT KKR civil, IITR envt Mtech + IOCL
Chairperson -
So introduce yourself to the board members.
So what is your work profile in IOCL.?
So you are from Gurgaon , recently there was a news of building of 6floors collapsing. How did this happen and why it happens even if there are so many checks during approval(something like this was asked)?
Continued on the same..
M1
What are the different shapes of sewers?
What are the characteristics of egg shaped sewers?
When it is prefered?
When combined sewers are used?
What are the advantages and disadvantages of using it?
How will you take care of Storm discharge?
What do we do in the primary treatment of sewage treatment plants?
What is oil skimmer?
Suppose today is 31st December and there is lot of oil next morning how will you take care of that ?(couldn't ans)
M2 (female)
(speaking slowly and less words used )
What are the different types of soil found in India ?
So black cotton soil should not be used according to you?
Okay tell me what are the different types of foundation used for construction?
You are currently in Prayagraj , what are the rivers flowing there?
M 3
So you have won in tennis some competition?
Tell me about dimensions of tennis court?
Convert In metres
Suppose you have to make an infrastructure so which city you'd prefer Gurgaon or Kurukshetra considering only environmental factors?
Tell me only environmental factors.
Okay leave .
What are the difficulties in making an infrastructure in Gurgaon?
Won't noise pollution be there
How will you overcome that
What measures u would take...and some more uncomfortable discussions in same domain
Chairperson
So is there any fav subject of yours which has not been asked from you?
( Said soil has been asked and RCC is also one of my fav sub)
M1 -
What is neutral axis?(wasn't impressed so told SOM wali too)
Draw stress distribution of a RC beam.
chairperson -Thankyou
Panel : Chairperson +3 members
Chairperson- Sujata mehta
1 female , 2 males in tech members
Date - 02/03/2022 ,time 11.26 am
Duration - 24 minutes
Background -NIT KKR civil, IITR envt Mtech + IOCL
Chairperson -
So introduce yourself to the board members.
So what is your work profile in IOCL.?
So you are from Gurgaon , recently there was a news of building of 6floors collapsing. How did this happen and why it happens even if there are so many checks during approval(something like this was asked)?
Continued on the same..
M1
What are the different shapes of sewers?
What are the characteristics of egg shaped sewers?
When it is prefered?
When combined sewers are used?
What are the advantages and disadvantages of using it?
How will you take care of Storm discharge?
What do we do in the primary treatment of sewage treatment plants?
What is oil skimmer?
Suppose today is 31st December and there is lot of oil next morning how will you take care of that ?(couldn't ans)
M2 (female)
(speaking slowly and less words used )
What are the different types of soil found in India ?
So black cotton soil should not be used according to you?
Okay tell me what are the different types of foundation used for construction?
You are currently in Prayagraj , what are the rivers flowing there?
M 3
So you have won in tennis some competition?
Tell me about dimensions of tennis court?
Convert In metres
Suppose you have to make an infrastructure so which city you'd prefer Gurgaon or Kurukshetra considering only environmental factors?
Tell me only environmental factors.
Okay leave .
What are the difficulties in making an infrastructure in Gurgaon?
Won't noise pollution be there
How will you overcome that
What measures u would take...and some more uncomfortable discussions in same domain
Chairperson
So is there any fav subject of yours which has not been asked from you?
( Said soil has been asked and RCC is also one of my fav sub)
M1 -
What is neutral axis?(wasn't impressed so told SOM wali too)
Draw stress distribution of a RC beam.
chairperson -Thankyou
👍1
Second shift
Board sathyavaty mam
Timing 25 30 minutes
Chairperson:
(read whole resume)
What were you doing after 2018
Why you didn't join any of those jobs
Why ES when you can join Aen post in your state having more blah blah nd ol in your local area
What is sustainable design
What is green building
What is difference between sustainable and green concept
M1
What is doda something I haven't heard of
What is dpc
Thickness and constituents
Purpose of dpc
Additional materials applied over it
Can you provide dpc in a 50 year old load bearing structure
Rainwater harvesting
M2
Btech project? (carbon fibre reinforced self compacting concrete)
Advantages of SCC
Advantage of carbon fibre
Carbon used was organic or inorganic
What is orthographic projection
Types of brick bonds
What is king closer nd queen closer
M3
What is a future city
What is smart city
What is climate change
How much is the average earth temperature
One simple calculative problem of carbon emission kinda we solve in environment
M2 again
You taught mathematics which topic u find difficult
Board sathyavaty mam
Timing 25 30 minutes
Chairperson:
(read whole resume)
What were you doing after 2018
Why you didn't join any of those jobs
Why ES when you can join Aen post in your state having more blah blah nd ol in your local area
What is sustainable design
What is green building
What is difference between sustainable and green concept
M1
What is doda something I haven't heard of
What is dpc
Thickness and constituents
Purpose of dpc
Additional materials applied over it
Can you provide dpc in a 50 year old load bearing structure
Rainwater harvesting
M2
Btech project? (carbon fibre reinforced self compacting concrete)
Advantages of SCC
Advantage of carbon fibre
Carbon used was organic or inorganic
What is orthographic projection
Types of brick bonds
What is king closer nd queen closer
M3
What is a future city
What is smart city
What is climate change
How much is the average earth temperature
One simple calculative problem of carbon emission kinda we solve in environment
M2 again
You taught mathematics which topic u find difficult
Date- 3rd march
Chairman
-read out daf
-what were you doing in the gap
-what have you learnt in training
-Full form rti and cgs
-what is sor
-if rate of certain item is not given in sor then how you will find out
-which type of market
Member 1
-SOR is given for which city
-how will you find cost in other cities
-what is cost index
-cpvc
-how to find slope of bathroom floor
-min and max steel for beam column
-cover for steel and column
Member 2
-S curve and its significance
-Advance surveying terms
-principal of bukinghum pie therom
-triangulation survey and its type
-flood routing and its significance
-types of flood routing
-explain muskinghum method
-water treatment plant both conventional and advance
-Advance treatment method for boiler feed water
-Zeolite method
Member 3
-More like a conversation like how to set advance solid waste management techniques
-design population and solid waste generated per capital per day
-composition of waste
-percentage of OM in solid waste as per indian scenario
-Do you think land filling is a good method
-leachates
-major gas released
-treatment method for leachates
Chairman
-read out daf
-what were you doing in the gap
-what have you learnt in training
-Full form rti and cgs
-what is sor
-if rate of certain item is not given in sor then how you will find out
-which type of market
Member 1
-SOR is given for which city
-how will you find cost in other cities
-what is cost index
-cpvc
-how to find slope of bathroom floor
-min and max steel for beam column
-cover for steel and column
Member 2
-S curve and its significance
-Advance surveying terms
-principal of bukinghum pie therom
-triangulation survey and its type
-flood routing and its significance
-types of flood routing
-explain muskinghum method
-water treatment plant both conventional and advance
-Advance treatment method for boiler feed water
-Zeolite method
Member 3
-More like a conversation like how to set advance solid waste management techniques
-design population and solid waste generated per capital per day
-composition of waste
-percentage of OM in solid waste as per indian scenario
-Do you think land filling is a good method
-leachates
-major gas released
-treatment method for leachates
I request all the candidates who have attended the interview, to share their Interview transcripts.
It need not be comprehensive, just a brief overview would also be helpful. ✌️
Do encourage your friends to share. It is time to earn some good Karma. 🖖
you can share through this doc, or post in the attached Group. 😇
https://bit.ly/3tnbdyn
It need not be comprehensive, just a brief overview would also be helpful. ✌️
Do encourage your friends to share. It is time to earn some good Karma. 🖖
you can share through this doc, or post in the attached Group. 😇
https://bit.ly/3tnbdyn
Google Docs
ESE CIVIL Eng. Interview Transcript 2022
Thankyou for sharing your interview experience, best of luck for results
Date 28/02/2022
afternoon session
sujata mehta mam
btech completed in 2020
mtech final sem from construction technology and management worked in L&T also
chairmen
why ese not L&T
why mtech ?
what is your thesis ? (precast technology )
what is your worked conclusion and result in project
what is 3D printing ?
what is precast ?
why houses not made through precast basically what are the challenges?
member 1
what is green building ?
provisions of green building?
what is rating?
which authority gives the rating?
what is griha and its full form
what is sustainable management?
how you ensure sustainable management as a engineer?
member 2
how precast is cost effective ?
you can make this upsc bhawawn with precast?
what is breakeven point in precast/
comparison of precast and cast in situ?
time reduce in precast
how to check reinforcement in slab ?
member 3
btech project ( muncipal solid waste management of indore city )
what is hazardous waste ?
what is nuclear waste ?
activated sludge process principal
what is noise pollution
measures to curb noise pollution ( I said concept of silent disco)
what are cpcb guidelines for this noise pollution ?
afternoon session
sujata mehta mam
btech completed in 2020
mtech final sem from construction technology and management worked in L&T also
chairmen
why ese not L&T
why mtech ?
what is your thesis ? (precast technology )
what is your worked conclusion and result in project
what is 3D printing ?
what is precast ?
why houses not made through precast basically what are the challenges?
member 1
what is green building ?
provisions of green building?
what is rating?
which authority gives the rating?
what is griha and its full form
what is sustainable management?
how you ensure sustainable management as a engineer?
member 2
how precast is cost effective ?
you can make this upsc bhawawn with precast?
what is breakeven point in precast/
comparison of precast and cast in situ?
time reduce in precast
how to check reinforcement in slab ?
member 3
btech project ( muncipal solid waste management of indore city )
what is hazardous waste ?
what is nuclear waste ?
activated sludge process principal
what is noise pollution
measures to curb noise pollution ( I said concept of silent disco)
what are cpcb guidelines for this noise pollution ?
Date: 4th March 2022
Session: Afternoon
Panel: Smt. Sujata Mehta
CH:-
1. Give your educational introduction.
2. Tell us about your B.Tech Project (Solid Waste Management).
3. What are the problems faced during Solid Waste Management that reduces the efficiency greatly?
4. Which cities in India have good Solid Waste Management?
5. What are the key features that separate them from other cities?
6. In what ways can the waste be reused?
M1:- (old,seemed to be a professor of IIT)
1. Tell me your favourite subjects. (Said Structural Analysis, Strength of Materials, Soil Mechanics, Fluid Mechanics)
2. How can you find the Pi-terms in dimensional analysis.
3. Do you require the concept of rank of matrix to find the pi-terms?
4. How is river modelled for testing in lab?
5. What material is used in lab for model testing?
6. What are the processes used in recycling of solid waste?
7. Which of these processes have been adopted in your city?
8. Can sludge be used in agriculture?
9. What is the concept used to convert sludge into biofeed?
10. Tell disadvantages of vermicomposting.
11. How will you select the site for the Waste Management Plant?
12. What are the requirements for the location of landfill?
13. Do you know about the JARGON table for selection of landfill?
M2:-(relatively young)
1. What is the system of Water Supply in you state? (Gujarat)
2. Is there a scarcity of water in Gujarat?
3. How can odour be removed from sewage?
4. What are different types of filters?
5. Which filter has most efficiency for odour removal?
6. What chemicals are used for removal of algae?
A few more questions on Environment which i don't remember.
M3:- (female member)
1. What are culverts?
2. Different types of culverts.
3. What are different types of foundation?
4. When is shallow foundation and deep foundation used?
5. What is tropic survey?
6. What is Astronomy?
7. What is Astronomy used for?
8. What is siphonic action?
9. How is the initial pressure provided to overcome summit height in a siphon?
10. Where is siphon used?
11. What are different types of valves and where are they provided?
CH:- Any subject you would like to be asked questions on? (Said Structural Analysis)
M1 asked 2-3 basic questions on indeterminacy as a formality
CH: Good. Thank you.
No questions on hobby.
Session: Afternoon
Panel: Smt. Sujata Mehta
CH:-
1. Give your educational introduction.
2. Tell us about your B.Tech Project (Solid Waste Management).
3. What are the problems faced during Solid Waste Management that reduces the efficiency greatly?
4. Which cities in India have good Solid Waste Management?
5. What are the key features that separate them from other cities?
6. In what ways can the waste be reused?
M1:- (old,seemed to be a professor of IIT)
1. Tell me your favourite subjects. (Said Structural Analysis, Strength of Materials, Soil Mechanics, Fluid Mechanics)
2. How can you find the Pi-terms in dimensional analysis.
3. Do you require the concept of rank of matrix to find the pi-terms?
4. How is river modelled for testing in lab?
5. What material is used in lab for model testing?
6. What are the processes used in recycling of solid waste?
7. Which of these processes have been adopted in your city?
8. Can sludge be used in agriculture?
9. What is the concept used to convert sludge into biofeed?
10. Tell disadvantages of vermicomposting.
11. How will you select the site for the Waste Management Plant?
12. What are the requirements for the location of landfill?
13. Do you know about the JARGON table for selection of landfill?
M2:-(relatively young)
1. What is the system of Water Supply in you state? (Gujarat)
2. Is there a scarcity of water in Gujarat?
3. How can odour be removed from sewage?
4. What are different types of filters?
5. Which filter has most efficiency for odour removal?
6. What chemicals are used for removal of algae?
A few more questions on Environment which i don't remember.
M3:- (female member)
1. What are culverts?
2. Different types of culverts.
3. What are different types of foundation?
4. When is shallow foundation and deep foundation used?
5. What is tropic survey?
6. What is Astronomy?
7. What is Astronomy used for?
8. What is siphonic action?
9. How is the initial pressure provided to overcome summit height in a siphon?
10. Where is siphon used?
11. What are different types of valves and where are they provided?
CH:- Any subject you would like to be asked questions on? (Said Structural Analysis)
M1 asked 2-3 basic questions on indeterminacy as a formality
CH: Good. Thank you.
No questions on hobby.
Date: 04/03/2022 ( Forenoon)
Chairman: M Satyavathi Ma'am
Background: 2019 passout. Brief stint with online Ed Tech platforms( Chegg etc)
Chairman: Read out the DAF almost completely.
- asked about gap
- how much did they pay you monthly ( Ed tech platform)
- what was your role exactly
- did they pay you in foreign currency or indian currency
- asked about college society membership(innovation & incubation club )
- any interesting idea you came across
- what if you're posted in chennai
- will be able to cope up with the env there
M1
- asked a purely mathematical question based on integration (pen & paper was allowed) regarding coal consumption of some country
- what is loudness
- what's the formula to calculate it
- frequency range for normal human hearing
- reference pressure value
- CPCB limits for noise level in residential area
- how do you measure sound level
M2
- difference bw internal wall & external wall
- thickness values of both
- pointed towards the floor & asked about type of tile used
- can we use the same in bathrooms
- why
- precautions you'd take before plastering a wall
- how would you accommodate ducts(plumbing or electrical) in a wall
- vertically or horizontally
-why
M3
- suppose a column shows visible buckling, what you do as an engineer to correct the column
- can you use all the methods you mentioned simultaneously
-why
- difference bw shear wall & partition wall
- what's coincidental draft
- why do u need to take max of thefinalltwo values
Discussed at length about this concept
- what's peak factor
- it's value
- now you're already accounting for unseen factors by using peak factors, why do we then use the concept of coincidental draft.
finally seemed convinced with the explanation
- how would you design a rural water supply scheme & an urban one
- will the domestic water demand be same
-why
- asked about values for LIG & HiG communities
- name the code with year/ latest revision
- what would you do next
Ch: That's it. You may leave now.
Chairman: M Satyavathi Ma'am
Background: 2019 passout. Brief stint with online Ed Tech platforms( Chegg etc)
Chairman: Read out the DAF almost completely.
- asked about gap
- how much did they pay you monthly ( Ed tech platform)
- what was your role exactly
- did they pay you in foreign currency or indian currency
- asked about college society membership(innovation & incubation club )
- any interesting idea you came across
- what if you're posted in chennai
- will be able to cope up with the env there
M1
- asked a purely mathematical question based on integration (pen & paper was allowed) regarding coal consumption of some country
- what is loudness
- what's the formula to calculate it
- frequency range for normal human hearing
- reference pressure value
- CPCB limits for noise level in residential area
- how do you measure sound level
M2
- difference bw internal wall & external wall
- thickness values of both
- pointed towards the floor & asked about type of tile used
- can we use the same in bathrooms
- why
- precautions you'd take before plastering a wall
- how would you accommodate ducts(plumbing or electrical) in a wall
- vertically or horizontally
-why
M3
- suppose a column shows visible buckling, what you do as an engineer to correct the column
- can you use all the methods you mentioned simultaneously
-why
- difference bw shear wall & partition wall
- what's coincidental draft
- why do u need to take max of thefinalltwo values
Discussed at length about this concept
- what's peak factor
- it's value
- now you're already accounting for unseen factors by using peak factors, why do we then use the concept of coincidental draft.
finally seemed convinced with the explanation
- how would you design a rural water supply scheme & an urban one
- will the domestic water demand be same
-why
- asked about values for LIG & HiG communities
- name the code with year/ latest revision
- what would you do next
Ch: That's it. You may leave now.
Name:XYZ
Anant sir panel
Last person to enter
Around 5:10pm
Duration 15mins
Date: 08/03/2021
Chairman: read about my btech and mtech clg name and asked where are these college
M1:
tell me about flood routing
Which method we used
Difference between them
Practically which method is good
Define CV
Interrupted saying i did not prepare hydrology
Few questions related to practical based I was unable to hear then he switched to rcc.
Asked about few questions about two way slabs
M2:
Explain his questions in Hindi
Like why we laid pipe in zigzag manner
For water supply to 10storey building which method you will use and how will ensure about the pressure
About central water commission
How will you save water in home
And in your area
Technical term abot water saving
M3:
difference between slope and deflection method, moment area method and conjugate beam method
Difference between moment and couple
If the moment you calculate at 1section from one should side from other side what will be the moment
Last question what did you do after 2017
I gave my answer in Hindi..so they asked me questions in Hindi
No questions from DAF, Mtech, Current affairs, Famous personalities
Interview happened with Face shield face mask hand gloves. During interview they will say if you are not comfortable with mask you can remove that
Glass panel was there among everone
mask and faceshields are provided by UPSC
Full payment of Travel allowance was there, for IRCTC air tickets.
Only pen and documents you have to carry into reception..they will provide place to put your belongings
Chairman sir is helpful and said jane do na sir bachi ko itna practical based questions ata nahi hai and everyone smiled..
They gave sandwich tea coffee water
Interview order is according to Who registered first (First come first service)
Be careful about the chair, It has wheels and it is rotating.. you have to control it :)
They said if you don't understand questions then asked us.but first understand the question clearly before answering.
Anant sir panel
Last person to enter
Around 5:10pm
Duration 15mins
Date: 08/03/2021
Chairman: read about my btech and mtech clg name and asked where are these college
M1:
tell me about flood routing
Which method we used
Difference between them
Practically which method is good
Define CV
Interrupted saying i did not prepare hydrology
Few questions related to practical based I was unable to hear then he switched to rcc.
Asked about few questions about two way slabs
M2:
Explain his questions in Hindi
Like why we laid pipe in zigzag manner
For water supply to 10storey building which method you will use and how will ensure about the pressure
About central water commission
How will you save water in home
And in your area
Technical term abot water saving
M3:
difference between slope and deflection method, moment area method and conjugate beam method
Difference between moment and couple
If the moment you calculate at 1section from one should side from other side what will be the moment
Last question what did you do after 2017
I gave my answer in Hindi..so they asked me questions in Hindi
No questions from DAF, Mtech, Current affairs, Famous personalities
Interview happened with Face shield face mask hand gloves. During interview they will say if you are not comfortable with mask you can remove that
Glass panel was there among everone
mask and faceshields are provided by UPSC
Full payment of Travel allowance was there, for IRCTC air tickets.
Only pen and documents you have to carry into reception..they will provide place to put your belongings
Chairman sir is helpful and said jane do na sir bachi ko itna practical based questions ata nahi hai and everyone smiled..
They gave sandwich tea coffee water
Interview order is according to Who registered first (First come first service)
Be careful about the chair, It has wheels and it is rotating.. you have to control it :)
They said if you don't understand questions then asked us.but first understand the question clearly before answering.
Name: ABC
Date: 08/03/2021
Chairman TC ANANT SIR
Morning session
Chairman ne sirf service aur profile puchi bas
2 cash crops,2 Zaid crops
Wheat base period
Can dam analysis be done by STAAD PRO
2 west flowing rivers
No of river basin in India
Name them
What is problem by taking excessive water from GWT
How can problem be solved
What is MDM method used for
What is your city famous for
What can you predict based on SCI-FI movies innovations in civil engineering future
What sci-fi movies you watch
what is DPR and CPR
Which states Narmada flows
This is all I can remember
Date: 08/03/2021
Chairman TC ANANT SIR
Morning session
Chairman ne sirf service aur profile puchi bas
2 cash crops,2 Zaid crops
Wheat base period
Can dam analysis be done by STAAD PRO
2 west flowing rivers
No of river basin in India
Name them
What is problem by taking excessive water from GWT
How can problem be solved
What is MDM method used for
What is your city famous for
What can you predict based on SCI-FI movies innovations in civil engineering future
What sci-fi movies you watch
what is DPR and CPR
Which states Narmada flows
This is all I can remember
Name: XYZ
Date:-08/03/2021
Chairman:- Anant Sir
Afternoon Session
Chairman
1.Why no Job?
2.Tell me about results of B.Tech Project
Member 1
1.Explain your project
2.Civil Engineering importance of your project
(IIT ke hoke aisa project karte ho😢)
3.Latitude and Longitude of Delhi
4.Traffic Sensor
5.Types of Spillways
6.Time of Concentration and use of Dicken's formula
7.Hydrograph for rainfall of duration 2Tc and Tc
8.Difference bw Pier and Abutment
9.Degree of Consolidation
10.Consolidation in detail
11.How excess PWP develops
12.Compaction and Consolidation diff.
13.All possible reasons for Differential Settlement and about Pisa Tower
14.Real life Field test for Soil
15.ILD and where is it used and it's significance
16.Which Software used in designing buildings
17.What is Subcritical Flow and real life examples
Member 2:-
1.Diff bw Subgrade and SubBase
2.Designing of Subgrade and SubBase
3.Tests before making Flexible Pavement
4.Triaxial test
5.CBR test in extra detail
6.English Bond and Flemish Bond
7.Modular Bricks and Nominal bricks diff
8.Pile load test in details
9.Under Reamed Pile and where is it used
10.Types of Failure in Foundation and which types of test
Member 3:-
1.Arc-GIS method in details
2.How to find capacity of Reservoirs
3.What is famous from your hometown
Date:-08/03/2021
Chairman:- Anant Sir
Afternoon Session
Chairman
1.Why no Job?
2.Tell me about results of B.Tech Project
Member 1
1.Explain your project
2.Civil Engineering importance of your project
(IIT ke hoke aisa project karte ho😢)
3.Latitude and Longitude of Delhi
4.Traffic Sensor
5.Types of Spillways
6.Time of Concentration and use of Dicken's formula
7.Hydrograph for rainfall of duration 2Tc and Tc
8.Difference bw Pier and Abutment
9.Degree of Consolidation
10.Consolidation in detail
11.How excess PWP develops
12.Compaction and Consolidation diff.
13.All possible reasons for Differential Settlement and about Pisa Tower
14.Real life Field test for Soil
15.ILD and where is it used and it's significance
16.Which Software used in designing buildings
17.What is Subcritical Flow and real life examples
Member 2:-
1.Diff bw Subgrade and SubBase
2.Designing of Subgrade and SubBase
3.Tests before making Flexible Pavement
4.Triaxial test
5.CBR test in extra detail
6.English Bond and Flemish Bond
7.Modular Bricks and Nominal bricks diff
8.Pile load test in details
9.Under Reamed Pile and where is it used
10.Types of Failure in Foundation and which types of test
Member 3:-
1.Arc-GIS method in details
2.How to find capacity of Reservoirs
3.What is famous from your hometown
Name: ABC
Chairman- Anant sir
Duration 25 to 30 min
Date: 09/03/2021
afternoon session
First two members asked questions related to m.tech and metro as i have done m.tech in structure and working in upmrc.
M1-Design of water tank
Detail reinforcement of circular tank
Force acting on water tank
M2 type of pile used in metro
How underground station constructed
Length of agra metro project
Type of section used for elevated section and different type of section used by dmrc
M3 i think he was from water resource or hydrology
He asked qns from FM irrigation and hydrology
Notch and weir
Flood routing
Pan coefficient
Base period and crop period
Chairman- Anant sir
Duration 25 to 30 min
Date: 09/03/2021
afternoon session
First two members asked questions related to m.tech and metro as i have done m.tech in structure and working in upmrc.
M1-Design of water tank
Detail reinforcement of circular tank
Force acting on water tank
M2 type of pile used in metro
How underground station constructed
Length of agra metro project
Type of section used for elevated section and different type of section used by dmrc
M3 i think he was from water resource or hydrology
He asked qns from FM irrigation and hydrology
Notch and weir
Flood routing
Pan coefficient
Base period and crop period
Name: ABC
Date: 09/03/2021
afternoon session
Panel -Bharat Bhusan Vyas
Entry
Chairperson- Is college se ho ,2019 Passout ho shi hai
Chairperson - Kya kr rhe avi
Fire kaise lgta hai building me
Fire proof building kaise bnate hai
Fire Extinguisher kaise kam krta hai
Divyang Logo ke liye bharat sarkar ne scheme nikal hai btao
Ek aur koi scheme pucha
Mjhe dono ni pta tha
( Aap log itne bde post pe ja rhe ho ye sb janna chahiye)
cement ke type btao
Pozzolana kya hota hai
Kya cement aur sand ke jagah fly ash use kr skte hai
Grades of cement
Technical Member 1-
Elective subject koun sa tha
(Maine Dam wala subject bol dia)
Dam ke type
Arch dam kyo use krte hai
Dam ka foundation kaise decide krte hai
Dam ke liye soil investigation hoga ki ni?
Koun sa test krenge soil investigation me
Member 2 -
Koi road yojna pucha jante ho ni pta tha mjhe
Monorail jante ho?
Mass Rapid Transit system
Building code jante ho
Bituminous road ke upper layer ke liye kya test krte hai
Marshal test kaise krte hai
LL 40% PL 26% then soil type
Member 3 -
What is new version of Is 800 ( Means year)
What new amendments have been added
Types of steel section
Difference between plastic and slender section
Why Mp value is more than My value
Date: 09/03/2021
afternoon session
Panel -Bharat Bhusan Vyas
Entry
Chairperson- Is college se ho ,2019 Passout ho shi hai
Chairperson - Kya kr rhe avi
Fire kaise lgta hai building me
Fire proof building kaise bnate hai
Fire Extinguisher kaise kam krta hai
Divyang Logo ke liye bharat sarkar ne scheme nikal hai btao
Ek aur koi scheme pucha
Mjhe dono ni pta tha
( Aap log itne bde post pe ja rhe ho ye sb janna chahiye)
cement ke type btao
Pozzolana kya hota hai
Kya cement aur sand ke jagah fly ash use kr skte hai
Grades of cement
Technical Member 1-
Elective subject koun sa tha
(Maine Dam wala subject bol dia)
Dam ke type
Arch dam kyo use krte hai
Dam ka foundation kaise decide krte hai
Dam ke liye soil investigation hoga ki ni?
Koun sa test krenge soil investigation me
Member 2 -
Koi road yojna pucha jante ho ni pta tha mjhe
Monorail jante ho?
Mass Rapid Transit system
Building code jante ho
Bituminous road ke upper layer ke liye kya test krte hai
Marshal test kaise krte hai
LL 40% PL 26% then soil type
Member 3 -
What is new version of Is 800 ( Means year)
What new amendments have been added
Types of steel section
Difference between plastic and slender section
Why Mp value is more than My value
👍1
INTERVIEW EXPERIENCE #1
Mine was on 8th march, I am here to tell you about order,
Basically it is first come first basis type in your slot (morning session and evening session), so mine was afternoon session ab there were 12 candidates to be interviewed, as expected there were 2 panels.
After checking at gates if you were ahead at waiting line then you get earlier entry and u will directed to reach at a place where baggage and mobile wallet have to be submitted, so the person who entered first gets lower number tag like no. 11th alloted to the first guy because 10 were already interviewed in morning batch, and this tag number is for seat seat no. In dv room in increasing order, and u r allowed to take your certificates folder, a pen and watch (if you you are having one) only to that seat, here after biometric n some signs, they check your 10th, 12th,degree,degree transcript, caste certificate, 2 passport size photo, and any other relevant document. (Here, safety kit offered, and wear mask and glovs from kit and a face sheet. During dv you may take off these except mask, but at the time of interview you have to wear facesheild and gloves back, told to take mask at chin tough) . And the 11th number candidate taken from dv place to the chairmen's office, at ouside office you have to wait for five more minutes until the bell rings, a guy opens the door for you, he will close the door also.
Mine was on 8th march, I am here to tell you about order,
Basically it is first come first basis type in your slot (morning session and evening session), so mine was afternoon session ab there were 12 candidates to be interviewed, as expected there were 2 panels.
After checking at gates if you were ahead at waiting line then you get earlier entry and u will directed to reach at a place where baggage and mobile wallet have to be submitted, so the person who entered first gets lower number tag like no. 11th alloted to the first guy because 10 were already interviewed in morning batch, and this tag number is for seat seat no. In dv room in increasing order, and u r allowed to take your certificates folder, a pen and watch (if you you are having one) only to that seat, here after biometric n some signs, they check your 10th, 12th,degree,degree transcript, caste certificate, 2 passport size photo, and any other relevant document. (Here, safety kit offered, and wear mask and glovs from kit and a face sheet. During dv you may take off these except mask, but at the time of interview you have to wear facesheild and gloves back, told to take mask at chin tough) . And the 11th number candidate taken from dv place to the chairmen's office, at ouside office you have to wait for five more minutes until the bell rings, a guy opens the door for you, he will close the door also.
👍1
INTERVIEW EXPERIENCE #2
There is no first-cum-first serve basis. Everything is pre-determined. Your panel and the order in which you will be called is already fixed and you have no say over that.
At Gate no. 1 you will be asked for e-summon letter and you Aadhar card.
After coming inside, you will be given your COVID kit and a place where you can keep your belongings. Only taking the required documents will be allowed.
After this document verification will be done. You will be asked to sit in the pre-defined order.
Sandwiches, tea, water are available.
After that you will be called according to their order.
Necessary things to carry- Btech degree, X certificate (8 semester marksheets not required), aadhar, self attested photocopies, 2 photographs.
It was just like you are sitting on a dining table meant for 6 people.
Something like this..
Dotted lines represent glass panels
There is no first-cum-first serve basis. Everything is pre-determined. Your panel and the order in which you will be called is already fixed and you have no say over that.
At Gate no. 1 you will be asked for e-summon letter and you Aadhar card.
After coming inside, you will be given your COVID kit and a place where you can keep your belongings. Only taking the required documents will be allowed.
After this document verification will be done. You will be asked to sit in the pre-defined order.
Sandwiches, tea, water are available.
After that you will be called according to their order.
Necessary things to carry- Btech degree, X certificate (8 semester marksheets not required), aadhar, self attested photocopies, 2 photographs.
It was just like you are sitting on a dining table meant for 6 people.
Something like this..
Dotted lines represent glass panels
Name-Ankit Yadav
Date - 10/03/2021, Afternoon session
Chairperson- BB Vyas
what are the major 5 projects of NHAI in INDIA?(Since I m currently working in NHAI)
what is the need of NHAI?
why speed and delay studies are done?
methods of speed delay studies?
what is home interview method?
what is grand challenge mechanism in Bharatmala pariyojna?
why traffic volume studies are done?
what are the different methods of tunneling ?
what is pilot tunnel?
what is industrial corridor?
what is defence corridor?
how it is different from industrial corridor?
Member 1
Do u know abt FRC?
In what form Fibres are used in the concrete?
Do u know abt any stretch of projects u mentioned where FRC is being used?
what are hanger bars?
Are hanger bars used in Bridge deck?
How load is transferred by deck in arch bridge?
what are the major forces which are generated in arch?
what are the structural elements in building which are designed for fatigue?
how the rupture of pressure vessels occurs?
what is the pattern of cracks?
Member 2
What is castigilano’s theorem?
what are causes and preventive measures for piping in earthen dam?
what are the causes of slope failure?
what are the different method for preventing slope failure?
How is soil nailing done?
what exactly is the mechanism by which soil nailing prevents slope failure?
what are the practical conditions where slope failure due to sudden drawdown occurs?
Member 3
why Firozabad is famous for? ( glass making)
what are different consituent used for glass manufacturing?
Different types of glasses?
Jo bathroom mn andha sheesha hota he use kya kehte hn aur kese banta he?
Have u seen the manufacturing of plastic bottle?
how plastic is affecting the environment?
what are the major alternatives?
Have u seen any canal?
What sections are generally provided in canal?
How velocity is controlled in canal?
P.S. The approach in which questions were asked was quite practical , I have written the crux of questions.
And the order of the interview was roll no. Wise in their respective panel.
Date - 10/03/2021, Afternoon session
Chairperson- BB Vyas
what are the major 5 projects of NHAI in INDIA?(Since I m currently working in NHAI)
what is the need of NHAI?
why speed and delay studies are done?
methods of speed delay studies?
what is home interview method?
what is grand challenge mechanism in Bharatmala pariyojna?
why traffic volume studies are done?
what are the different methods of tunneling ?
what is pilot tunnel?
what is industrial corridor?
what is defence corridor?
how it is different from industrial corridor?
Member 1
Do u know abt FRC?
In what form Fibres are used in the concrete?
Do u know abt any stretch of projects u mentioned where FRC is being used?
what are hanger bars?
Are hanger bars used in Bridge deck?
How load is transferred by deck in arch bridge?
what are the major forces which are generated in arch?
what are the structural elements in building which are designed for fatigue?
how the rupture of pressure vessels occurs?
what is the pattern of cracks?
Member 2
What is castigilano’s theorem?
what are causes and preventive measures for piping in earthen dam?
what are the causes of slope failure?
what are the different method for preventing slope failure?
How is soil nailing done?
what exactly is the mechanism by which soil nailing prevents slope failure?
what are the practical conditions where slope failure due to sudden drawdown occurs?
Member 3
why Firozabad is famous for? ( glass making)
what are different consituent used for glass manufacturing?
Different types of glasses?
Jo bathroom mn andha sheesha hota he use kya kehte hn aur kese banta he?
Have u seen the manufacturing of plastic bottle?
how plastic is affecting the environment?
what are the major alternatives?
Have u seen any canal?
What sections are generally provided in canal?
How velocity is controlled in canal?
P.S. The approach in which questions were asked was quite practical , I have written the crux of questions.
And the order of the interview was roll no. Wise in their respective panel.
👍2