CVE-2025-37957 - KVM SVM SMM Shutdown Interception Forced Exit
CVE ID : CVE-2025-37957
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: KVM: SVM: Forcibly leave SMM mode on SHUTDOWN interception Previously, commit ed129ec9057f ("KVM: x86: forcibly leave nested mode on vCPU reset") addressed an issue where a triple fault occurring in nested mode could lead to use-after-free scenarios. However, the commit did not handle the analogous situation for System Management Mode (SMM). This omission results in triggering a WARN when KVM forces a vCPU INIT after SHUTDOWN interception while the vCPU is in SMM. This situation was reprodused using Syzkaller by: 1) Creating a KVM VM and vCPU 2) Sending a KVM_SMI ioctl to explicitly enter SMM 3) Executing invalid instructions causing consecutive exceptions and eventually a triple fault The issue manifests as follows: WARNING: CPU: 0 PID: 25506 at arch/x86/kvm/x86.c:12112 kvm_vcpu_reset+0x1d2/0x1530 arch/x86/kvm/x86.c:12112 Modules linked in: CPU: 0 PID: 25506 Comm: syz-executor.0 Not tainted 6.1.130-syzkaller-00157-g164fe5dde9b6 #0 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014 RIP: 0010:kvm_vcpu_reset+0x1d2/0x1530 arch/x86/kvm/x86.c:12112 Call Trace: shutdown_interception+0x66/0xb0 arch/x86/kvm/svm/svm.c:2136 svm_invoke_exit_handler+0x110/0x530 arch/x86/kvm/svm/svm.c:3395 svm_handle_exit+0x424/0x920 arch/x86/kvm/svm/svm.c:3457 vcpu_enter_guest arch/x86/kvm/x86.c:10959 [inline] vcpu_run+0x2c43/0x5a90 arch/x86/kvm/x86.c:11062 kvm_arch_vcpu_ioctl_run+0x50f/0x1cf0 arch/x86/kvm/x86.c:11283 kvm_vcpu_ioctl+0x570/0xf00 arch/x86/kvm/../../../virt/kvm/kvm_main.c:4122 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:870 [inline] __se_sys_ioctl fs/ioctl.c:856 [inline] __x64_sys_ioctl+0x19a/0x210 fs/ioctl.c:856 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x35/0x80 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 Architecturally, INIT is blocked when the CPU is in SMM, hence KVM's WARN() in kvm_vcpu_reset() to guard against KVM bugs, e.g. to detect improper emulation of INIT. SHUTDOWN on SVM is a weird edge case where KVM needs to do _something_ sane with the VMCB, since it's technically undefined, and INIT is the least awful choice given KVM's ABI. So, double down on stuffing INIT on SHUTDOWN, and force the vCPU out of SMM to avoid any weirdness (and the WARN). Found by Linux Verification Center (linuxtesting.org) with Syzkaller. [sean: massage changelog, make it clear this isn't architectural behavior]
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-37957
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: KVM: SVM: Forcibly leave SMM mode on SHUTDOWN interception Previously, commit ed129ec9057f ("KVM: x86: forcibly leave nested mode on vCPU reset") addressed an issue where a triple fault occurring in nested mode could lead to use-after-free scenarios. However, the commit did not handle the analogous situation for System Management Mode (SMM). This omission results in triggering a WARN when KVM forces a vCPU INIT after SHUTDOWN interception while the vCPU is in SMM. This situation was reprodused using Syzkaller by: 1) Creating a KVM VM and vCPU 2) Sending a KVM_SMI ioctl to explicitly enter SMM 3) Executing invalid instructions causing consecutive exceptions and eventually a triple fault The issue manifests as follows: WARNING: CPU: 0 PID: 25506 at arch/x86/kvm/x86.c:12112 kvm_vcpu_reset+0x1d2/0x1530 arch/x86/kvm/x86.c:12112 Modules linked in: CPU: 0 PID: 25506 Comm: syz-executor.0 Not tainted 6.1.130-syzkaller-00157-g164fe5dde9b6 #0 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014 RIP: 0010:kvm_vcpu_reset+0x1d2/0x1530 arch/x86/kvm/x86.c:12112 Call Trace: shutdown_interception+0x66/0xb0 arch/x86/kvm/svm/svm.c:2136 svm_invoke_exit_handler+0x110/0x530 arch/x86/kvm/svm/svm.c:3395 svm_handle_exit+0x424/0x920 arch/x86/kvm/svm/svm.c:3457 vcpu_enter_guest arch/x86/kvm/x86.c:10959 [inline] vcpu_run+0x2c43/0x5a90 arch/x86/kvm/x86.c:11062 kvm_arch_vcpu_ioctl_run+0x50f/0x1cf0 arch/x86/kvm/x86.c:11283 kvm_vcpu_ioctl+0x570/0xf00 arch/x86/kvm/../../../virt/kvm/kvm_main.c:4122 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:870 [inline] __se_sys_ioctl fs/ioctl.c:856 [inline] __x64_sys_ioctl+0x19a/0x210 fs/ioctl.c:856 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x35/0x80 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 Architecturally, INIT is blocked when the CPU is in SMM, hence KVM's WARN() in kvm_vcpu_reset() to guard against KVM bugs, e.g. to detect improper emulation of INIT. SHUTDOWN on SVM is a weird edge case where KVM needs to do _something_ sane with the VMCB, since it's technically undefined, and INIT is the least awful choice given KVM's ABI. So, double down on stuffing INIT on SHUTDOWN, and force the vCPU out of SMM to avoid any weirdness (and the WARN). Found by Linux Verification Center (linuxtesting.org) with Syzkaller. [sean: massage changelog, make it clear this isn't architectural behavior]
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-37958 - Linux Kernel Huge Memory PMD Migration Entry Invalid Address Access Vulnerability
CVE ID : CVE-2025-37958
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: mm/huge_memory: fix dereferencing invalid pmd migration entry When migrating a THP, concurrent access to the PMD migration entry during a deferred split scan can lead to an invalid address access, as illustrated below. To prevent this invalid access, it is necessary to check the PMD migration entry and return early. In this context, there is no need to use pmd_to_swp_entry and pfn_swap_entry_to_page to verify the equality of the target folio. Since the PMD migration entry is locked, it cannot be served as the target. Mailing list discussion and explanation from Hugh Dickins: "An anon_vma lookup points to a location which may contain the folio of interest, but might instead contain another folio: and weeding out those other folios is precisely what the "folio != pmd_folio((*pmd)" check (and the "risk of replacing the wrong folio" comment a few lines above it) is for." BUG: unable to handle page fault for address: ffffea60001db008 CPU: 0 UID: 0 PID: 2199114 Comm: tee Not tainted 6.14.0+ #4 NONE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:split_huge_pmd_locked+0x3b5/0x2b60 Call Trace: try_to_migrate_one+0x28c/0x3730 rmap_walk_anon+0x4f6/0x770 unmap_folio+0x196/0x1f0 split_huge_page_to_list_to_order+0x9f6/0x1560 deferred_split_scan+0xac5/0x12a0 shrinker_debugfs_scan_write+0x376/0x470 full_proxy_write+0x15c/0x220 vfs_write+0x2fc/0xcb0 ksys_write+0x146/0x250 do_syscall_64+0x6a/0x120 entry_SYSCALL_64_after_hwframe+0x76/0x7e The bug is found by syzkaller on an internal kernel, then confirmed on upstream.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-37958
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: mm/huge_memory: fix dereferencing invalid pmd migration entry When migrating a THP, concurrent access to the PMD migration entry during a deferred split scan can lead to an invalid address access, as illustrated below. To prevent this invalid access, it is necessary to check the PMD migration entry and return early. In this context, there is no need to use pmd_to_swp_entry and pfn_swap_entry_to_page to verify the equality of the target folio. Since the PMD migration entry is locked, it cannot be served as the target. Mailing list discussion and explanation from Hugh Dickins: "An anon_vma lookup points to a location which may contain the folio of interest, but might instead contain another folio: and weeding out those other folios is precisely what the "folio != pmd_folio((*pmd)" check (and the "risk of replacing the wrong folio" comment a few lines above it) is for." BUG: unable to handle page fault for address: ffffea60001db008 CPU: 0 UID: 0 PID: 2199114 Comm: tee Not tainted 6.14.0+ #4 NONE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:split_huge_pmd_locked+0x3b5/0x2b60 Call Trace: try_to_migrate_one+0x28c/0x3730 rmap_walk_anon+0x4f6/0x770 unmap_folio+0x196/0x1f0 split_huge_page_to_list_to_order+0x9f6/0x1560 deferred_split_scan+0xac5/0x12a0 shrinker_debugfs_scan_write+0x376/0x470 full_proxy_write+0x15c/0x220 vfs_write+0x2fc/0xcb0 ksys_write+0x146/0x250 do_syscall_64+0x6a/0x120 entry_SYSCALL_64_after_hwframe+0x76/0x7e The bug is found by syzkaller on an internal kernel, then confirmed on upstream.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-37959 - Linux Kernel BPF Scrub Packet on bpf_redirect_peer Information Disclosure
CVE ID : CVE-2025-37959
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: bpf: Scrub packet on bpf_redirect_peer When bpf_redirect_peer is used to redirect packets to a device in another network namespace, the skb isn't scrubbed. That can lead skb information from one namespace to be "misused" in another namespace. As one example, this is causing Cilium to drop traffic when using bpf_redirect_peer to redirect packets that just went through IPsec decryption to a container namespace. The following pwru trace shows (1) the packet path from the host's XFRM layer to the container's XFRM layer where it's dropped and (2) the number of active skb extensions at each function. NETNS MARK IFACE TUPLE FUNC 4026533547 d00 eth0 10.244.3.124:35473->10.244.2.158:53 xfrm_rcv_cb .active_extensions = (__u8)2, 4026533547 d00 eth0 10.244.3.124:35473->10.244.2.158:53 xfrm4_rcv_cb .active_extensions = (__u8)2, 4026533547 d00 eth0 10.244.3.124:35473->10.244.2.158:53 gro_cells_receive .active_extensions = (__u8)2, [...] 4026533547 0 eth0 10.244.3.124:35473->10.244.2.158:53 skb_do_redirect .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 ip_rcv .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 ip_rcv_core .active_extensions = (__u8)2, [...] 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 udp_queue_rcv_one_skb .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 __xfrm_policy_check .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 __xfrm_decode_session .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 security_xfrm_decode_session .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 kfree_skb_reason(SKB_DROP_REASON_XFRM_POLICY) .active_extensions = (__u8)2, In this case, there are no XFRM policies in the container's network namespace so the drop is unexpected. When we decrypt the IPsec packet, the XFRM state used for decryption is set in the skb extensions. This information is preserved across the netns switch. When we reach the XFRM policy check in the container's netns, __xfrm_policy_check drops the packet with LINUX_MIB_XFRMINNOPOLS because a (container-side) XFRM policy can't be found that matches the (host-side) XFRM state used for decryption. This patch fixes this by scrubbing the packet when using bpf_redirect_peer, as is done on typical netns switches via veth devices except skb->mark and skb->tstamp are not zeroed.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-37959
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: bpf: Scrub packet on bpf_redirect_peer When bpf_redirect_peer is used to redirect packets to a device in another network namespace, the skb isn't scrubbed. That can lead skb information from one namespace to be "misused" in another namespace. As one example, this is causing Cilium to drop traffic when using bpf_redirect_peer to redirect packets that just went through IPsec decryption to a container namespace. The following pwru trace shows (1) the packet path from the host's XFRM layer to the container's XFRM layer where it's dropped and (2) the number of active skb extensions at each function. NETNS MARK IFACE TUPLE FUNC 4026533547 d00 eth0 10.244.3.124:35473->10.244.2.158:53 xfrm_rcv_cb .active_extensions = (__u8)2, 4026533547 d00 eth0 10.244.3.124:35473->10.244.2.158:53 xfrm4_rcv_cb .active_extensions = (__u8)2, 4026533547 d00 eth0 10.244.3.124:35473->10.244.2.158:53 gro_cells_receive .active_extensions = (__u8)2, [...] 4026533547 0 eth0 10.244.3.124:35473->10.244.2.158:53 skb_do_redirect .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 ip_rcv .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 ip_rcv_core .active_extensions = (__u8)2, [...] 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 udp_queue_rcv_one_skb .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 __xfrm_policy_check .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 __xfrm_decode_session .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 security_xfrm_decode_session .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 kfree_skb_reason(SKB_DROP_REASON_XFRM_POLICY) .active_extensions = (__u8)2, In this case, there are no XFRM policies in the container's network namespace so the drop is unexpected. When we decrypt the IPsec packet, the XFRM state used for decryption is set in the skb extensions. This information is preserved across the netns switch. When we reach the XFRM policy check in the container's netns, __xfrm_policy_check drops the packet with LINUX_MIB_XFRMINNOPOLS because a (container-side) XFRM policy can't be found that matches the (host-side) XFRM state used for decryption. This patch fixes this by scrubbing the packet when using bpf_redirect_peer, as is done on typical netns switches via veth devices except skb->mark and skb->tstamp are not zeroed.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-37960 - Linux Kernel Memblock Accept Memory Vulnerability
CVE ID : CVE-2025-37960
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: memblock: Accept allocated memory before use in memblock_double_array() When increasing the array size in memblock_double_array() and the slab is not yet available, a call to memblock_find_in_range() is used to reserve/allocate memory. However, the range returned may not have been accepted, which can result in a crash when booting an SNP guest: RIP: 0010:memcpy_orig+0x68/0x130 Code: ... RSP: 0000:ffffffff9cc03ce8 EFLAGS: 00010006 RAX: ff11001ff83e5000 RBX: 0000000000000000 RCX: fffffffffffff000 RDX: 0000000000000bc0 RSI: ffffffff9dba8860 RDI: ff11001ff83e5c00 RBP: 0000000000002000 R08: 0000000000000000 R09: 0000000000002000 R10: 000000207fffe000 R11: 0000040000000000 R12: ffffffff9d06ef78 R13: ff11001ff83e5000 R14: ffffffff9dba7c60 R15: 0000000000000c00 memblock_double_array+0xff/0x310 memblock_add_range+0x1fb/0x2f0 memblock_reserve+0x4f/0xa0 memblock_alloc_range_nid+0xac/0x130 memblock_alloc_internal+0x53/0xc0 memblock_alloc_try_nid+0x3d/0xa0 swiotlb_init_remap+0x149/0x2f0 mem_init+0xb/0xb0 mm_core_init+0x8f/0x350 start_kernel+0x17e/0x5d0 x86_64_start_reservations+0x14/0x30 x86_64_start_kernel+0x92/0xa0 secondary_startup_64_no_verify+0x194/0x19b Mitigate this by calling accept_memory() on the memory range returned before the slab is available. Prior to v6.12, the accept_memory() interface used a 'start' and 'end' parameter instead of 'start' and 'size', therefore the accept_memory() call must be adjusted to specify 'start + size' for 'end' when applying to kernels prior to v6.12.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-37960
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: memblock: Accept allocated memory before use in memblock_double_array() When increasing the array size in memblock_double_array() and the slab is not yet available, a call to memblock_find_in_range() is used to reserve/allocate memory. However, the range returned may not have been accepted, which can result in a crash when booting an SNP guest: RIP: 0010:memcpy_orig+0x68/0x130 Code: ... RSP: 0000:ffffffff9cc03ce8 EFLAGS: 00010006 RAX: ff11001ff83e5000 RBX: 0000000000000000 RCX: fffffffffffff000 RDX: 0000000000000bc0 RSI: ffffffff9dba8860 RDI: ff11001ff83e5c00 RBP: 0000000000002000 R08: 0000000000000000 R09: 0000000000002000 R10: 000000207fffe000 R11: 0000040000000000 R12: ffffffff9d06ef78 R13: ff11001ff83e5000 R14: ffffffff9dba7c60 R15: 0000000000000c00 memblock_double_array+0xff/0x310 memblock_add_range+0x1fb/0x2f0 memblock_reserve+0x4f/0xa0 memblock_alloc_range_nid+0xac/0x130 memblock_alloc_internal+0x53/0xc0 memblock_alloc_try_nid+0x3d/0xa0 swiotlb_init_remap+0x149/0x2f0 mem_init+0xb/0xb0 mm_core_init+0x8f/0x350 start_kernel+0x17e/0x5d0 x86_64_start_reservations+0x14/0x30 x86_64_start_kernel+0x92/0xa0 secondary_startup_64_no_verify+0x194/0x19b Mitigate this by calling accept_memory() on the memory range returned before the slab is available. Prior to v6.12, the accept_memory() interface used a 'start' and 'end' parameter instead of 'start' and 'size', therefore the accept_memory() call must be adjusted to specify 'start + size' for 'end' when applying to kernels prior to v6.12.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-37962 - Linux Kernel ksmbd Memory Leak Vulnerability
CVE ID : CVE-2025-37962
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix memory leak in parse_lease_state() The previous patch that added bounds check for create lease context introduced a memory leak. When the bounds check fails, the function returns NULL without freeing the previously allocated lease_ctx_info structure. This patch fixes the issue by adding kfree(lreq) before returning NULL in both boundary check cases.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-37962
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix memory leak in parse_lease_state() The previous patch that added bounds check for create lease context introduced a memory leak. When the bounds check fails, the function returns NULL without freeing the previously allocated lease_ctx_info structure. This patch fixes the issue by adding kfree(lreq) before returning NULL in both boundary check cases.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-37963 - "Linux Kernel ARM64 BPF Unprivileged User Mitigation Vulnerability"
CVE ID : CVE-2025-37963
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: arm64: bpf: Only mitigate cBPF programs loaded by unprivileged users Support for eBPF programs loaded by unprivileged users is typically disabled. This means only cBPF programs need to be mitigated for BHB. In addition, only mitigate cBPF programs that were loaded by an unprivileged user. Privileged users can also load the same program via eBPF, making the mitigation pointless.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-37963
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: arm64: bpf: Only mitigate cBPF programs loaded by unprivileged users Support for eBPF programs loaded by unprivileged users is typically disabled. This means only cBPF programs need to be mitigated for BHB. In addition, only mitigate cBPF programs that were loaded by an unprivileged user. Privileged users can also load the same program via eBPF, making the mitigation pointless.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-37964 - Linux Kernel: Intel X86 TLB Flush Inadvertent Skipping Vulnerability
CVE ID : CVE-2025-37964
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: x86/mm: Eliminate window where TLB flushes may be inadvertently skipped tl;dr: There is a window in the mm switching code where the new CR3 is set and the CPU should be getting TLB flushes for the new mm. But should_flush_tlb() has a bug and suppresses the flush. Fix it by widening the window where should_flush_tlb() sends an IPI. Long Version: === History === There were a few things leading up to this. First, updating mm_cpumask() was observed to be too expensive, so it was made lazier. But being lazy caused too many unnecessary IPIs to CPUs due to the now-lazy mm_cpumask(). So code was added to cull mm_cpumask() periodically[2]. But that culling was a bit too aggressive and skipped sending TLB flushes to CPUs that need them. So here we are again. === Problem === The too-aggressive code in should_flush_tlb() strikes in this window: // Turn on IPIs for this CPU/mm combination, but only // if should_flush_tlb() agrees: cpumask_set_cpu(cpu, mm_cpumask(next)); next_tlb_gen = atomic64_read(&next->context.tlb_gen); choose_new_asid(next, next_tlb_gen, &new_asid, &need_flush); load_new_mm_cr3(need_flush); // ^ After 'need_flush' is set to false, IPIs *MUST* // be sent to this CPU and not be ignored. this_cpu_write(cpu_tlbstate.loaded_mm, next); // ^ Not until this point does should_flush_tlb() // become true! should_flush_tlb() will suppress TLB flushes between load_new_mm_cr3() and writing to 'loaded_mm', which is a window where they should not be suppressed. Whoops. === Solution === Thankfully, the fuzzy "just about to write CR3" window is already marked with loaded_mm==LOADED_MM_SWITCHING. Simply checking for that state in should_flush_tlb() is sufficient to ensure that the CPU is targeted with an IPI. This will cause more TLB flush IPIs. But the window is relatively small and I do not expect this to cause any kind of measurable performance impact. Update the comment where LOADED_MM_SWITCHING is written since it grew yet another user. Peter Z also raised a concern that should_flush_tlb() might not observe 'loaded_mm' and 'is_lazy' in the same order that switch_mm_irqs_off() writes them. Add a barrier to ensure that they are observed in the order they are written.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-37964
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: x86/mm: Eliminate window where TLB flushes may be inadvertently skipped tl;dr: There is a window in the mm switching code where the new CR3 is set and the CPU should be getting TLB flushes for the new mm. But should_flush_tlb() has a bug and suppresses the flush. Fix it by widening the window where should_flush_tlb() sends an IPI. Long Version: === History === There were a few things leading up to this. First, updating mm_cpumask() was observed to be too expensive, so it was made lazier. But being lazy caused too many unnecessary IPIs to CPUs due to the now-lazy mm_cpumask(). So code was added to cull mm_cpumask() periodically[2]. But that culling was a bit too aggressive and skipped sending TLB flushes to CPUs that need them. So here we are again. === Problem === The too-aggressive code in should_flush_tlb() strikes in this window: // Turn on IPIs for this CPU/mm combination, but only // if should_flush_tlb() agrees: cpumask_set_cpu(cpu, mm_cpumask(next)); next_tlb_gen = atomic64_read(&next->context.tlb_gen); choose_new_asid(next, next_tlb_gen, &new_asid, &need_flush); load_new_mm_cr3(need_flush); // ^ After 'need_flush' is set to false, IPIs *MUST* // be sent to this CPU and not be ignored. this_cpu_write(cpu_tlbstate.loaded_mm, next); // ^ Not until this point does should_flush_tlb() // become true! should_flush_tlb() will suppress TLB flushes between load_new_mm_cr3() and writing to 'loaded_mm', which is a window where they should not be suppressed. Whoops. === Solution === Thankfully, the fuzzy "just about to write CR3" window is already marked with loaded_mm==LOADED_MM_SWITCHING. Simply checking for that state in should_flush_tlb() is sufficient to ensure that the CPU is targeted with an IPI. This will cause more TLB flush IPIs. But the window is relatively small and I do not expect this to cause any kind of measurable performance impact. Update the comment where LOADED_MM_SWITCHING is written since it grew yet another user. Peter Z also raised a concern that should_flush_tlb() might not observe 'loaded_mm' and 'is_lazy' in the same order that switch_mm_irqs_off() writes them. Add a barrier to ensure that they are observed in the order they are written.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-48014 - Apache Directory LDAP Authentication Password Guessing Bypass
CVE ID : CVE-2025-48014
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : Password guessing limits could be bypassed when using LDAP authentication.
Severity: 7.5 | HIGH
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-48014
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : Password guessing limits could be bypassed when using LDAP authentication.
Severity: 7.5 | HIGH
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-48015 - Apache Stratosphere Authentication Information Disclosure
CVE ID : CVE-2025-48015
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : Failed login response could be different depending on whether the username was local or central.
Severity: 3.7 | LOW
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-48015
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : Failed login response could be different depending on whether the username was local or central.
Severity: 3.7 | LOW
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-48016 - Cisco OpenFlow Discovery Protocol Resource Exhaustion Vulnerability
CVE ID : CVE-2025-48016
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : OpenFlow discovery protocol can exhaust resources because it is not rate limited
Severity: 4.3 | MEDIUM
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-48016
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : OpenFlow discovery protocol can exhaust resources because it is not rate limited
Severity: 4.3 | MEDIUM
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-48017 - Apache Circuit File Upload Path Traversal
CVE ID : CVE-2025-48017
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : Improper limitation of pathname in Circuit Provisioning and File Import applications allows modification and uploading of files
Severity: 9.0 | CRITICAL
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-48017
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : Improper limitation of pathname in Circuit Provisioning and File Import applications allows modification and uploading of files
Severity: 9.0 | CRITICAL
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-48018 - Adobe ColdFusion Cross-Site Scripting (XSS)
CVE ID : CVE-2025-48018
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : An authenticated user can modify application state data.
Severity: 7.5 | HIGH
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-48018
Published : May 20, 2025, 4:15 p.m. | 1 hour, 11 minutes ago
Description : An authenticated user can modify application state data.
Severity: 7.5 | HIGH
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-37989 - Linux Kernel Phy LED Trigger Memory Leak Vulnerability
CVE ID : CVE-2025-37989
Published : May 20, 2025, 6:15 p.m. | 3 hours, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: net: phy: leds: fix memory leak A network restart test on a router led to an out-of-memory condition, which was traced to a memory leak in the PHY LED trigger code. The root cause is misuse of the devm API. The registration function (phy_led_triggers_register) is called from phy_attach_direct, not phy_probe, and the unregister function (phy_led_triggers_unregister) is called from phy_detach, not phy_remove. This means the register and unregister functions can be called multiple times for the same PHY device, but devm-allocated memory is not freed until the driver is unbound. This also prevents kmemleak from detecting the leak, as the devm API internally stores the allocated pointer. Fix this by replacing devm_kzalloc/devm_kcalloc with standard kzalloc/kcalloc, and add the corresponding kfree calls in the unregister path.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-37989
Published : May 20, 2025, 6:15 p.m. | 3 hours, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: net: phy: leds: fix memory leak A network restart test on a router led to an out-of-memory condition, which was traced to a memory leak in the PHY LED trigger code. The root cause is misuse of the devm API. The registration function (phy_led_triggers_register) is called from phy_attach_direct, not phy_probe, and the unregister function (phy_led_triggers_unregister) is called from phy_detach, not phy_remove. This means the register and unregister functions can be called multiple times for the same PHY device, but devm-allocated memory is not freed until the driver is unbound. This also prevents kmemleak from detecting the leak, as the devm API internally stores the allocated pointer. Fix this by replacing devm_kzalloc/devm_kcalloc with standard kzalloc/kcalloc, and add the corresponding kfree calls in the unregister path.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-37990 - "Broadcom brcm80211 WiFi Linux Kernel Uninitialized Variable Use"
CVE ID : CVE-2025-37990
Published : May 20, 2025, 6:15 p.m. | 3 hours, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: wifi: brcm80211: fmac: Add error handling for brcmf_usb_dl_writeimage() The function brcmf_usb_dl_writeimage() calls the function brcmf_usb_dl_cmd() but dose not check its return value. The 'state.state' and the 'state.bytes' are uninitialized if the function brcmf_usb_dl_cmd() fails. It is dangerous to use uninitialized variables in the conditions. Add error handling for brcmf_usb_dl_cmd() to jump to error handling path if the brcmf_usb_dl_cmd() fails and the 'state.state' and the 'state.bytes' are uninitialized. Improve the error message to report more detailed error information.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-37990
Published : May 20, 2025, 6:15 p.m. | 3 hours, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: wifi: brcm80211: fmac: Add error handling for brcmf_usb_dl_writeimage() The function brcmf_usb_dl_writeimage() calls the function brcmf_usb_dl_cmd() but dose not check its return value. The 'state.state' and the 'state.bytes' are uninitialized if the function brcmf_usb_dl_cmd() fails. It is dangerous to use uninitialized variables in the conditions. Add error handling for brcmf_usb_dl_cmd() to jump to error handling path if the brcmf_usb_dl_cmd() fails and the 'state.state' and the 'state.bytes' are uninitialized. Improve the error message to report more detailed error information.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-37991 - HP parisc SIGFPE Double Crash Vulnerability
CVE ID : CVE-2025-37991
Published : May 20, 2025, 6:15 p.m. | 3 hours, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: parisc: Fix double SIGFPE crash Camm noticed that on parisc a SIGFPE exception will crash an application with a second SIGFPE in the signal handler. Dave analyzed it, and it happens because glibc uses a double-word floating-point store to atomically update function descriptors. As a result of lazy binding, we hit a floating-point store in fpe_func almost immediately. When the T bit is set, an assist exception trap occurs when when the co-processor encounters *any* floating-point instruction except for a double store of register %fr0. The latter cancels all pending traps. Let's fix this by clearing the Trap (T) bit in the FP status register before returning to the signal handler in userspace. The issue can be reproduced with this test program: root@parisc:~# cat fpe.c static void fpe_func(int sig, siginfo_t *i, void *v) { sigset_t set; sigemptyset(&set); sigaddset(&set, SIGFPE); sigprocmask(SIG_UNBLOCK, &set, NULL); printf("GOT signal %d with si_code %ld\n", sig, i->si_code); } int main() { struct sigaction action = { .sa_sigaction = fpe_func, .sa_flags = SA_RESTART|SA_SIGINFO }; sigaction(SIGFPE, &action, 0); feenableexcept(FE_OVERFLOW); return printf("%lf\n",1.7976931348623158E308*1.7976931348623158E308); } root@parisc:~# gcc fpe.c -lm root@parisc:~# ./a.out Floating point exception root@parisc:~# strace -f ./a.out execve("./a.out", ["./a.out"], 0xf9ac7034 /* 20 vars */) = 0 getrlimit(RLIMIT_STACK, {rlim_cur=8192*1024, rlim_max=RLIM_INFINITY}) = 0 ... rt_sigaction(SIGFPE, {sa_handler=0x1110a, sa_mask=[], sa_flags=SA_RESTART|SA_SIGINFO}, NULL, 8) = 0 --- SIGFPE {si_signo=SIGFPE, si_code=FPE_FLTOVF, si_addr=0x1078f} --- --- SIGFPE {si_signo=SIGFPE, si_code=FPE_FLTOVF, si_addr=0xf8f21237} --- +++ killed by SIGFPE +++ Floating point exception
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-37991
Published : May 20, 2025, 6:15 p.m. | 3 hours, 11 minutes ago
Description : In the Linux kernel, the following vulnerability has been resolved: parisc: Fix double SIGFPE crash Camm noticed that on parisc a SIGFPE exception will crash an application with a second SIGFPE in the signal handler. Dave analyzed it, and it happens because glibc uses a double-word floating-point store to atomically update function descriptors. As a result of lazy binding, we hit a floating-point store in fpe_func almost immediately. When the T bit is set, an assist exception trap occurs when when the co-processor encounters *any* floating-point instruction except for a double store of register %fr0. The latter cancels all pending traps. Let's fix this by clearing the Trap (T) bit in the FP status register before returning to the signal handler in userspace. The issue can be reproduced with this test program: root@parisc:~# cat fpe.c static void fpe_func(int sig, siginfo_t *i, void *v) { sigset_t set; sigemptyset(&set); sigaddset(&set, SIGFPE); sigprocmask(SIG_UNBLOCK, &set, NULL); printf("GOT signal %d with si_code %ld\n", sig, i->si_code); } int main() { struct sigaction action = { .sa_sigaction = fpe_func, .sa_flags = SA_RESTART|SA_SIGINFO }; sigaction(SIGFPE, &action, 0); feenableexcept(FE_OVERFLOW); return printf("%lf\n",1.7976931348623158E308*1.7976931348623158E308); } root@parisc:~# gcc fpe.c -lm root@parisc:~# ./a.out Floating point exception root@parisc:~# strace -f ./a.out execve("./a.out", ["./a.out"], 0xf9ac7034 /* 20 vars */) = 0 getrlimit(RLIMIT_STACK, {rlim_cur=8192*1024, rlim_max=RLIM_INFINITY}) = 0 ... rt_sigaction(SIGFPE, {sa_handler=0x1110a, sa_mask=[], sa_flags=SA_RESTART|SA_SIGINFO}, NULL, 8) = 0 --- SIGFPE {si_signo=SIGFPE, si_code=FPE_FLTOVF, si_addr=0x1078f} --- --- SIGFPE {si_signo=SIGFPE, si_code=FPE_FLTOVF, si_addr=0xf8f21237} --- +++ killed by SIGFPE +++ Floating point exception
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-46724 - Langroid TableChatAgent Code Injection Vulnerability
CVE ID : CVE-2025-46724
Published : May 20, 2025, 6:15 p.m. | 3 hours, 11 minutes ago
Description : Langroid is a Python framework to build large language model (LLM)-powered applications. Prior to version 0.53.15, `TableChatAgent` uses `pandas eval()`. If fed by untrusted user input, like the case of a public-facing LLM application, it may be vulnerable to code injection. Langroid 0.53.15 sanitizes input to `TableChatAgent` by default to tackle the most common attack vectors, and added several warnings about the risky behavior in the project documentation.
Severity: 9.8 | CRITICAL
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-46724
Published : May 20, 2025, 6:15 p.m. | 3 hours, 11 minutes ago
Description : Langroid is a Python framework to build large language model (LLM)-powered applications. Prior to version 0.53.15, `TableChatAgent` uses `pandas eval()`. If fed by untrusted user input, like the case of a public-facing LLM application, it may be vulnerable to code injection. Langroid 0.53.15 sanitizes input to `TableChatAgent` by default to tackle the most common attack vectors, and added several warnings about the risky behavior in the project documentation.
Severity: 9.8 | CRITICAL
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-46725 - Langroid LanceDocChatAgent Pandas Evaluator Command Injection
CVE ID : CVE-2025-46725
Published : May 20, 2025, 6:15 p.m. | 3 hours, 11 minutes ago
Description : Langroid is a Python framework to build large language model (LLM)-powered applications. Prior to version 0.53.15, `LanceDocChatAgent` uses pandas eval() through `compute_from_docs()`. As a result, an attacker may be able to make the agent run malicious commands through `QueryPlan.dataframe_calc]`) compromising the host system. Langroid 0.53.15 sanitizes input to the affected function by default to tackle the most common attack vectors, and added several warnings about the risky behavior in the project documentation.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-46725
Published : May 20, 2025, 6:15 p.m. | 3 hours, 11 minutes ago
Description : Langroid is a Python framework to build large language model (LLM)-powered applications. Prior to version 0.53.15, `LanceDocChatAgent` uses pandas eval() through `compute_from_docs()`. As a result, an attacker may be able to make the agent run malicious commands through `QueryPlan.dataframe_calc]`) compromising the host system. Langroid 0.53.15 sanitizes input to the affected function by default to tackle the most common attack vectors, and added several warnings about the risky behavior in the project documentation.
Severity: 0.0 | NA
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-47277 - NVIDIA vLLM Unauthenticated Remote Code Execution
CVE ID : CVE-2025-47277
Published : May 20, 2025, 6:15 p.m. | 3 hours, 11 minutes ago
Description : vLLM, an inference and serving engine for large language models (LLMs), has an issue in versions 0.6.5 through 0.8.4 that ONLY impacts environments using the `PyNcclPipe` KV cache transfer integration with the V0 engine. No other configurations are affected. vLLM supports the use of the `PyNcclPipe` class to establish a peer-to-peer communication domain for data transmission between distributed nodes. The GPU-side KV-Cache transmission is implemented through the `PyNcclCommunicator` class, while CPU-side control message passing is handled via the `send_obj` and `recv_obj` methods on the CPU side. The intention was that this interface should only be exposed to a private network using the IP address specified by the `--kv-ip` CLI parameter. The vLLM documentation covers how this must be limited to a secured network. The default and intentional behavior from PyTorch is that the `TCPStore` interface listens on ALL interfaces, regardless of what IP address is provided. The IP address given was only used as a client-side address to use. vLLM was fixed to use a workaround to force the `TCPStore` instance to bind its socket to a specified private interface. As of version 0.8.5, vLLM limits the `TCPStore` socket to the private interface as configured.
Severity: 9.8 | CRITICAL
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-47277
Published : May 20, 2025, 6:15 p.m. | 3 hours, 11 minutes ago
Description : vLLM, an inference and serving engine for large language models (LLMs), has an issue in versions 0.6.5 through 0.8.4 that ONLY impacts environments using the `PyNcclPipe` KV cache transfer integration with the V0 engine. No other configurations are affected. vLLM supports the use of the `PyNcclPipe` class to establish a peer-to-peer communication domain for data transmission between distributed nodes. The GPU-side KV-Cache transmission is implemented through the `PyNcclCommunicator` class, while CPU-side control message passing is handled via the `send_obj` and `recv_obj` methods on the CPU side. The intention was that this interface should only be exposed to a private network using the IP address specified by the `--kv-ip` CLI parameter. The vLLM documentation covers how this must be limited to a secured network. The default and intentional behavior from PyTorch is that the `TCPStore` interface listens on ALL interfaces, regardless of what IP address is provided. The IP address given was only used as a client-side address to use. vLLM was fixed to use a workaround to force the `TCPStore` instance to bind its socket to a specified private interface. As of version 0.8.5, vLLM limits the `TCPStore` socket to the private interface as configured.
Severity: 9.8 | CRITICAL
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-47850 - JetBrains YouTrack Attachment Visibility Bypass
CVE ID : CVE-2025-47850
Published : May 20, 2025, 6:15 p.m. | 3 hours, 11 minutes ago
Description : In JetBrains YouTrack before 2025.1.74704 restricted attachments could become visible after issue cloning
Severity: 4.3 | MEDIUM
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-47850
Published : May 20, 2025, 6:15 p.m. | 3 hours, 11 minutes ago
Description : In JetBrains YouTrack before 2025.1.74704 restricted attachments could become visible after issue cloning
Severity: 4.3 | MEDIUM
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE-2025-47851 - JetBrains TeamCity Stored XSS Vulnerability
CVE ID : CVE-2025-47851
Published : May 20, 2025, 6:15 p.m. | 3 hours, 11 minutes ago
Description : In JetBrains TeamCity before 2025.03.2 stored XSS via GitHub Checks Webhook was possible
Severity: 4.8 | MEDIUM
Visit the link for more details, such as CVSS details, affected products, timeline, and more...
CVE ID : CVE-2025-47851
Published : May 20, 2025, 6:15 p.m. | 3 hours, 11 minutes ago
Description : In JetBrains TeamCity before 2025.03.2 stored XSS via GitHub Checks Webhook was possible
Severity: 4.8 | MEDIUM
Visit the link for more details, such as CVSS details, affected products, timeline, and more...