Non-Inverting Op-Amp


In this configuration of Op-amp the input signal is directly fed to the non inverting terminal resulting in a positive gain and output voltage in phase with input as compared to inverting Op-amp where the gain is negative and output voltage is out of phase with input , and to stabalize the circuit a negative feedback is applied through a resistor(Rf) and the inverting terminal is grounded witha input resistor(R2).

This inverting Op-Amp like layout the at inverting terminal creates a virtual ground at the summing point make the Rf and R2 a potential divider accross inverting terminal, Hence determines the gain of the circuit.

@BasicElectronics

What is a Schmitt Trigger?

A Schmitt trigger is a comparator (not exclusively) circuit that makes use of positive feedback (small changes in the input lead to large changes in the output in the same phase) to implement hysteresis (a fancy word for delayed action) and is used to remove noise from an analog signal while converting it to a digital one.

It was invented way back in 1937 by Otto H. Schmitt (whose legacy is somewhat understated) who called it a ‘thermionic trigger’.

@BasicElectronics

Designed to accurately produce the required output waveform with the addition of just a few extra timing components.

One such device that has been around since the early days of IC’s and has itself become something of an industry “standard” is the 555 Timer Oscillator which is more commonly called the “555 Timer”.

The basic 555 timer gets its name from the fact that there are three internally connected 5kΩ resistors which it uses to generate the two comparators reference voltages. The 555 timer IC is a very cheap, popular and useful precision timing device which can act as either a simple timer to generate single pulses or long time delays, or as a relaxation oscillator producing a string of stabilised waveforms of varying duty cycles from 50 to 100%.

@BasicElectronics

What is a laser diode?

👉The LASER in Laser Diode is an acronym for 'Light Amplification by Stimulated Emission of Radiation'. It is also referred to as a semiconductor laser and generally abbreviated as LD.

👉Its main feature is high coherency, making it possible to emit light with the same phase and wavelength.

👉Laser oscillation is achieved by amplifying light generated through current injection between two mirrors. Simply put, a laser diode is an LED that amplifies and emits light using reflectors.

@BasicElectronics

What is wireless charging?

👉Wireless charging is a technology that charges devices without using connectors or metal contacts.

👉This is also referred to as non-contact charging, non-contact power transmission, and wireless power supply.

👉Wireless charging technology is attracting increased attention by eliminating the need for power cords when charging.

👉 This is expected to increase connector safety and resistance to dust and water while enabling multiple devices to be charged using a single charger.

@BasicElectronics

Decibels
Unit is Bel, but because this is large, deci-Bels (1/10th Bel) are used), Symbol is dB.

Decibels are used in audio because they are a logarithmic measure of voltage, current or power, and correspond well to the response of the ear.

A 3dB change is half or double the power (0.707 or 1.414 times voltage or current respectively).
@BasicElectronics

Cathode Ray Tube

CRT

Cathode ray tube display technology is mostly used in televisions and computer screens that work on the movement of an electron beam back and forth on the back of the screen. This tube is an elongated vacuum tube in which the flattened surface has external components as an electron gun, electron beam, and a phosphorescent screen

@BasicElectronics

The Differential Amplifier

The differential amplifier amplifies the voltage difference present on its inverting and non-inverting inputs

differential amplifiers amplify the difference between two voltages making this type of operational amplifier circuit a Subtractor unlike a summing amplifier which adds or sums together the input voltages. This type of operational amplifier circuit is commonly known as a Differential Amplifier configuration

@BasicElectronics

Wheatstone bridge

Wheatstone bridge, also known as the resistance bridge, calculates the unknown resistance by balancing two legs of the bridge circuit. One leg includes the component of unknown resistance.


The Wheatstone Bridge Circuit comprises two known resistors, one unknown resistor and one variable resistor connected in the form of a bridge. This bridge is very reliable as it gives accurate measurements.

@BasicElectronics

Kirchhoff’s Current Law


According to Kirchhoff’s Current Law,

The total current entering a junction or a node is equal to the charge leaving the node as no charge is lost.

Put differently, the algebraic sum of every current entering and leaving the node has to be null. This property of Kirchhoff law is commonly called Conservation of charge wherein, I(exit) + I(enter) = 0.

In the above figure, the currents I1, I2 and I3 entering the node is considered positive, likewise, the currents I4 and I5 exiting the nodes is considered negative in values. This can be expressed in the form of an equation:

I1 + I2 + I3 – I4 – I5 = 0

The term Node refers to a junction or a connection of two or more current-carrying routes like cables and other components.

Kirchhoff’s current law can also be applied to analyze parallel circuits.

@BasicElectronics

Kirchhoff’s Voltage Law


According to Kirchhoff’s Voltage Law,

The voltage around a loop equals to the sum of every voltage drop in the same loop for any closed network and also equals to zero.

Put differently, the algebraic sum of every voltage in the loop has to be equal to zero and this property of Kirchhoff’s law is called conservation of energy.

When you begin at any point of the loop and continue in the same direction, note the voltage drops in all the directions either negative or positive and return to the same point. It is essential to maintain the direction either counterclockwise or clockwise; else the final voltage value will not be equal to zero. The voltage law can also be applied in analyzing circuits in series.

@BasicElectronics

Quality Factor


The quality factor or Q factor is a measure of the performance of a coil, capacitor inductor in terms of its losses and resonator bandwidth. Simple formulas can relate the variables.

The definition of quality factor is often needed to give a more exact understanding of what this quantity actually is.

For electronic circuits, Q is defined as the ratio of the energy stored in the resonator to the energy supplied by a to it, per cycle, to keep signal amplitude constant, at a frequency where the stored energy is constant with time.

It can also be defined for an inductor as the ratio of its inductive reactance to its resistance at a particular frequency, and it is a measure of its efficiency.

@BasicElectronics

Lines of Force from a Bar Magnets Magnetic Field

However, magnetic flux does not actually flow from the north to the south pole or flow anywhere for that matter as magnetic flux is a static region around a magnet in which the magnetic force exists. In other words magnetic flux does not flow or move it is just there and is not influenced by gravity. Some important facts emerge when plotting lines of force:

✅ Lines of force NEVER cross.

✅ Lines of force are CONTINUOUS.

✅ Lines of force always form individual CLOSED LOOPS around the magnet.

✅ Lines of force have a definite

✅ DIRECTION from North to South.

✅ Lines of force that are close together indicate a STRONG magnetic field.

✅ Lines of force that are farther apart indicate a WEAK magnetic field.

@BasicElectronics

Passive Attenuators
A Passive Attenuator is a special type of electrical or electronic bidirectional circuit made up of entirely resistive elements.

👉An attenuator is a two port resistive network designed to weaken or “attenuate” (hence their name) the power being supplied by a source to a level that is suitable for the connected load.

👉It reduces the amount of power being delivered to the connected load by either a single fixed amount, a variable amount or in a series of known switchable steps.
These are generally used in radio, communication and transmission line applications to weaken a stronger signal.

👉It is a purely passive resistive network (hence no supply) which is used in a wide variety of electronic equipment for extending the dynamic range of measuring equipment by adjusting signal levels, to provide impedance matching of oscillators or amplifiers to reduce the effects of improper input/output terminations, or to simply provide isolation between difference

@BasicElectronics

Commonly used ICs in electronic circuits:

555 timer IC: A versatile IC that can be used as an oscillator, pulse generator, or timer, often used in timing and clock circuits.

7400 series ICs: A family of digital logic ICs that contains a variety of gates, flip-flops, and other building blocks for digital circuits, commonly used in computers and other digital devices.

LM386 audio amplifier IC: A low-power audio amplifier that can be used to amplify small signals, often used in portable audio devices and musical instruments.

LM7805 voltage regulator IC: A linear voltage regulator that can provide a stable 5V DC output, often used to power microcontrollers and other electronic devices.

CD4017 decade counter IC: A digital counter that can count from 0 to 9 and then reset, often used in sequential circuits and display circuits.

CD4053 multiplexer IC: A digital IC that can select one of several inputs and route it to a common output, often used in data acquisition and control systems.

@BasicElectronics

VLSI (very-large-scale integration) is a term used to describe the process of creating very complex integrated circuits (ICs) that contain millions or billions of transistors and other components on a single chip. VLSI circuits are used in a wide range of applications, including computers, smartphones, and other electronic devices.

👉🏻VLSI technology has made it possible to create highly complex and powerful electronic systems that are smaller, faster, and more energy-efficient than ever before. VLSI circuits are typically designed using computer-aided design (CAD) tools and manufactured using photolithography and other advanced technologies.

👉🏻VLSI design and development require a strong foundation in electrical engineering, computer science, and other related fields. VLSI engineers often work in teams to design, test, and verify VLSI circuits, and may also be involved in the manufacturing process.

@BasicElectronics

A MOSFET (metal-oxide-semiconductor field-effect transistor) is a type of field-effect transistor (FET) that uses a metal-oxide gate electrode to control the flow of electrons between the source and drain. MOSFETs are commonly used in many different types of electronic circuits and devices, including computers, smartphones, and other electronic devices.

👉🏻MOSFETs are known for their high switching speed, low power consumption, and high input impedance. They can be used as switches, amplifiers, or to control the flow of current in a circuit. MOSFETs are typically classified as either n-channel or p-channel, depending on the type of semiconductor material used.

👉🏻MOSFETs are widely used in many applications due to their versatility and high performance. They are often preferred over other types of transistors, such as bipolar junction transistors (BJTs), due to their low power consumption and high switching speed.

@BasicElectronics

Different types of MOSFETs:

Enhancement mode MOSFET: This type of MOSFET is turned on when a positive voltage is applied to the gate. It is commonly used as a switch in electronic circuits.

Depletion mode MOSFET: This type of MOSFET is turned on when a negative voltage is applied to the gate. It is commonly used in circuits that require a variable resistor.

n-channel MOSFET: This type of MOSFET uses an n-type semiconductor material, which means that it has an excess of electrons. It is commonly used in high-speed switching applications.

p-channel MOSFET: This type of MOSFET uses a p-type semiconductor material, which means that it has a deficiency of electrons. It is commonly used in low-power switching applications.

JFET (junction field-effect transistor): This type of MOSFET uses a pn junction to control the flow of electrons, rather than a metal-oxide gate. It is commonly used in low-power and low-frequency applications.

MOSFET amplifier: This type of MOSFET uses multiple transistors to amplify an input signal. It is commonly used in audio and radio frequency (RF) circuits.

@BasicElectronics

A GAAFET (gate-all-around field-effect transistor) is a type of field-effect transistor (FET) that uses a gate that surrounds the channel on all sides. GAAFETs are a next-generation technology that offers several advantages over traditional MOSFETs, such as higher switching speeds and lower power consumption.

👉🏻GAAFETs are typically made using a multi-gate architecture, where the gate wraps around the channel on all four sides. This allows the gate to control the flow of electrons more effectively, resulting in higher performance and improved device characteristics. GAAFETs are also often made using novel materials, such as graphene or other 2D materials, which can further enhance their performance.

👉🏻GAAFETs are still in the development and research phase, and are not yet widely used in commercial applications. However, they have the potential to revolutionize the electronics industry by enabling faster, more efficient, and more compact electronic devices.

@BasicElectronics