Operation: Connect to Z3X EasyJtagPlus
Setting Interface to EasyJtag2/UFS ISP
Setting IO Levels to Low
Setting Frequence to 66 Mhz
Socket Information :
Socket Mark: EasyJTAG UFS Socket BGA-254 by EasyJTAG 31.12.22
Socket Serial: 0123A862FFB9B569EE
Socket Type: UFS_SOCKET_BGA_254
UFS Power Information :
Mode: Low, VCC: 3308 mV, VCCQ2: 1938 mV
UFS Device Information :
UFS Manufacturer: SAMSUNG, UFS ProductName: KMAG9001PM-B814
UFS Version: 3.1, UFS OemID: SAMSUNG_OEM_ID, UFS FirmVersion: 5.00, UFS SerialNumber: 55bcc0685019
Maximum Number of LUs: 8, Number of LUs found: 4, Number of WLUs found: 1, LUs Re-configure: Enabled
RPMB Counter: 3306
UFS LUN 0 (Main Boot A) Capacity: 4 MB (000000400000)
UFS LUN 1 (Boot B) Capacity: 4 MB (000000400000)
UFS LUN 2 Capacity: 122028 MB (001DCAC00000)
UFS LUN 3 Capacity: 4 MB (000000400000)
UFS card does not support type of memory for LUN 0. This value will be replaced by the first supported
UFS card does not support type of memory for LUN 1. This value will be replaced by the first supported
UFS card does not support type of memory for LUN 2. This value will be replaced by the first supported
UFS card does not support type of memory for LUN 3. This value will be replaced by the first supported
UFS card does not support type of memory for LUN 4. This value will be replaced by the first supported
UFS card does not support type of memory for LUN 5. This value will be replaced by the first supported
UFS card does not support type of memory for LUN 6. This value will be replaced by the first supported
UFS card does not support type of memory for LUN 7. This value will be replaced by the first supported
Device Life Time Estimation B: 0x02 10% - 20% device life time used
Device Life Time Estimation A: 0x02 10% - 20% device life time used
Pre EOL information: 0x01 Normal (Consumed less then 80% of reserved block)
Backup saved: UFS_SAMSUNG_KMAG9001PM-B814_55bcc0685019_20250418_135931_config.ini (old backup)
Do not turn the socket before you press "Close Session" button
Connected successfully
Operation: Scan PartitionTable from Source (Vendor: Binary Read/Write)
Scanning soft partitions from LUN 0 (Main Boot A)
UFS_SWITCH_PART: START_LUN failed: -507 UIC: Link initialization fail
Error reading at address: 000000000000 , error: -700, API_UFS_LUN_NOT_SELECTED ... Retry #1
Canceled
Setting Interface to EasyJtag2/UFS ISP
Setting IO Levels to Low
Setting Frequence to 66 Mhz
Socket Information :
Socket Mark: EasyJTAG UFS Socket BGA-254 by EasyJTAG 31.12.22
Socket Serial: 0123A862FFB9B569EE
Socket Type: UFS_SOCKET_BGA_254
UFS Power Information :
Mode: Low, VCC: 3308 mV, VCCQ2: 1938 mV
UFS Device Information :
UFS Manufacturer: SAMSUNG, UFS ProductName: KMAG9001PM-B814
UFS Version: 3.1, UFS OemID: SAMSUNG_OEM_ID, UFS FirmVersion: 5.00, UFS SerialNumber: 55bcc0685019
Maximum Number of LUs: 8, Number of LUs found: 4, Number of WLUs found: 1, LUs Re-configure: Enabled
RPMB Counter: 3306
UFS LUN 0 (Main Boot A) Capacity: 4 MB (000000400000)
UFS LUN 1 (Boot B) Capacity: 4 MB (000000400000)
UFS LUN 2 Capacity: 122028 MB (001DCAC00000)
UFS LUN 3 Capacity: 4 MB (000000400000)
UFS card does not support type of memory for LUN 0. This value will be replaced by the first supported
UFS card does not support type of memory for LUN 1. This value will be replaced by the first supported
UFS card does not support type of memory for LUN 2. This value will be replaced by the first supported
UFS card does not support type of memory for LUN 3. This value will be replaced by the first supported
UFS card does not support type of memory for LUN 4. This value will be replaced by the first supported
UFS card does not support type of memory for LUN 5. This value will be replaced by the first supported
UFS card does not support type of memory for LUN 6. This value will be replaced by the first supported
UFS card does not support type of memory for LUN 7. This value will be replaced by the first supported
Device Life Time Estimation B: 0x02 10% - 20% device life time used
Device Life Time Estimation A: 0x02 10% - 20% device life time used
Pre EOL information: 0x01 Normal (Consumed less then 80% of reserved block)
Backup saved: UFS_SAMSUNG_KMAG9001PM-B814_55bcc0685019_20250418_135931_config.ini (old backup)
Do not turn the socket before you press "Close Session" button
Connected successfully
Operation: Scan PartitionTable from Source (Vendor: Binary Read/Write)
Scanning soft partitions from LUN 0 (Main Boot A)
UFS_SWITCH_PART: START_LUN failed: -507 UIC: Link initialization fail
Error reading at address: 000000000000 , error: -700, API_UFS_LUN_NOT_SELECTED ... Retry #1
Canceled
Setting Interface to EasyJtag2/UFS ISP
Setting IO Levels to Low
Setting Frequence to 66 Mhz
Socket Information :
Socket Mark: EasyJTAG UFS Socket BGA-254 by EasyJTAG 31.12.22
Socket Serial: 0123A862FFB9B569EE
Socket Type: UFS_SOCKET_BGA_254
UFS Power Information :
Mode: Low, VCC: 3304 mV, VCCQ2: 1939 mV
UFS Device Information :
UFS Manufacturer: HG, UFS ProductName: CBE06-1280CHAC
UFS Version: 2.2, UFS OemID: 0x00, UFS FirmVersion: 110, UFS SerialNumber: 770970240126002CE9C0
Maximum Number of LUs: 32, Number of LUs found: 6, Number of WLUs found: 1, LUs Re-configure: Enabled
RPMB Counter: 6571
UFS LUN 0 Capacity: 119048 MB (001D10800000)
UFS LUN 1 (Main Boot A) Capacity: 8 MB (000000800000)
UFS LUN 2 (Boot B) Capacity: 8 MB (000000800000)
UFS LUN 3 Capacity: 32 MB (000002000000)
UFS LUN 4 Capacity: 3072 MB (0000C0000000)
UFS LUN 5 Capacity: 32 MB (000002000000)
Device Life Time Estimation B: 0x01 0% - 10% device life time used
Device Life Time Estimation A: 0x01 0% - 10% device life time used
Pre EOL information: 0x01 Normal (Consumed less then 80% of reserved block)
Backup saved: UFS_HG_CBE06-1280CHAC_770970240126002CE9C0_20250503_181751_config.ini (old backup)
Do not turn the socket before you press "Close Session" button
Connected successfully
Operation: Scan PartitionTable from Source (Vendor: Binary Read/Write)
Scanning soft partitions from LUN 0
Error reading at address: 000000000000 , error: -206, PORT: Read Error ... Retry #1
Canceled
Setting IO Levels to Low
Setting Frequence to 66 Mhz
Socket Information :
Socket Mark: EasyJTAG UFS Socket BGA-254 by EasyJTAG 31.12.22
Socket Serial: 0123A862FFB9B569EE
Socket Type: UFS_SOCKET_BGA_254
UFS Power Information :
Mode: Low, VCC: 3304 mV, VCCQ2: 1939 mV
UFS Device Information :
UFS Manufacturer: HG, UFS ProductName: CBE06-1280CHAC
UFS Version: 2.2, UFS OemID: 0x00, UFS FirmVersion: 110, UFS SerialNumber: 770970240126002CE9C0
Maximum Number of LUs: 32, Number of LUs found: 6, Number of WLUs found: 1, LUs Re-configure: Enabled
RPMB Counter: 6571
UFS LUN 0 Capacity: 119048 MB (001D10800000)
UFS LUN 1 (Main Boot A) Capacity: 8 MB (000000800000)
UFS LUN 2 (Boot B) Capacity: 8 MB (000000800000)
UFS LUN 3 Capacity: 32 MB (000002000000)
UFS LUN 4 Capacity: 3072 MB (0000C0000000)
UFS LUN 5 Capacity: 32 MB (000002000000)
Device Life Time Estimation B: 0x01 0% - 10% device life time used
Device Life Time Estimation A: 0x01 0% - 10% device life time used
Pre EOL information: 0x01 Normal (Consumed less then 80% of reserved block)
Backup saved: UFS_HG_CBE06-1280CHAC_770970240126002CE9C0_20250503_181751_config.ini (old backup)
Do not turn the socket before you press "Close Session" button
Connected successfully
Operation: Scan PartitionTable from Source (Vendor: Binary Read/Write)
Scanning soft partitions from LUN 0
Error reading at address: 000000000000 , error: -206, PORT: Read Error ... Retry #1
Canceled
ound 2 serial devices
COM14 USB\VID_05C6&PID_9008&REV_0000 Qualcomm HS-USB QDLoader 9008 (COM14)
COM4 USB\VID_1781&PID_AAAC&REV_0100&MI_00 USB Serial Device (COM4)
Failed to find resource: IDR_DSA_PEMSelected pinout: GEN2 ISP Pinout
Change EasyJTAG Pinout OK
Z3X EasyJtag Software ver. 3.8.0.10
UFS Socket Info.
Serial: 0123A862FFB9B569EE
Description: EasyJTAG UFS Socket BGA-254 by EasyJTAG 31.12.22
Identify UFS Chip.
UFS Chip Voltage: Low
Check ISP connect.
Calibrate ISP.
VCC: 2857mV
VCCQ2: 1934mV
Chip Info:
Manufacturer: HG
ProductName: CBE06-1280CHAC
SerialNumber: 770970240126002CE9C0
OemID: 0x00
Firmware Version: 11
UFS Reference Clock: 19.2MHz
UFS Version: 2.2
Maximum Number of LUs: 32
Number of LUs found: 6
LUN 0:
Block size: 0x1000
Size: 0x1D10800000 / 116,264,000,000B / 116GB
LUN 1 (Main Boot A):
Block size: 0x1000
Size: 0x800000 / 0,008,000,000B / 8MB
LUN 2 (Boot B):
Block size: 0x1000
Size: 0x800000 / 0,008,000,000B / 8MB
LUN 3:
Block size: 0x1000
Size: 0x2000000 / 0,032,000,000B / 32MB
LUN 4:
Block size: 0x1000
Size: 0xC0000000 / 3,000,000,000B / 3GB
LUN 5:
Block size: 0x1000
Size: 0x2000000 / 0,032,000,000B / 32MB
Number of W-LUs found: 1
W-LUN 0xC4 (RPMB):
Block size: 0x100
Size: 0x1000000 / 0,016,000,000B / 16MB
Full size: 0x1DD7800000 / 119,376,000,000B / 119GB
RPMB:
Counter: 6571
Health:
Device life time method A: 0x01 (0%-10% device life time used)
Device life time method B: 0x01 (0%-10% device life time used)
Pre End of Life: 0x01 (Used less then 80% of reserved blocks)
Checking LUs for partitioning
LUN0 Have 21 partitions
Can't stop LUN0, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN1, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN2, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN3, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN4, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN5, Code: -428677518, Reason: Unknown error (-428677518)
Read USERDATA from LUN0.
Can't start LUN0, Code: -428677518, Reason: Unknown error (-428677518)
Done.
ound 2 serial devices
COM14 USB\VID_05C6&PID_9008&REV_0000 Qualcomm HS-USB QDLoader 9008 (COM14)
COM4 USB\VID_1781&PID_AAAC&REV_0100&MI_00 USB Serial Device (COM4)
Failed to find resource: IDR_DSA_PEMSelected pinout: GEN2 ISP Pinout
Change EasyJTAG Pinout OK
Z3X EasyJtag Software ver. 3.8.0.10
UFS Socket Info.
Serial: 0123A862FFB9B569EE
Description: EasyJTAG UFS Socket BGA-254 by EasyJTAG 31.12.22
Identify UFS Chip.
UFS Chip Voltage: Low
Check ISP connect.
Calibrate ISP.
VCC: 2857mV
VCCQ2: 1934mV
Chip Info:
Manufacturer: HG
ProductName: CBE06-1280CHAC
SerialNumber: 770970240126002CE9C0
OemID: 0x00
Firmware Version: 11
UFS Reference Clock: 19.2MHz
UFS Version: 2.2
Maximum Number of LUs: 32
Number of LUs found: 6
LUN 0:
Block size: 0x1000
Size: 0x1D10800000 / 116,264,000,000B / 116GB
LUN 1 (Main Boot A):
Block size: 0x1000
Size: 0x800000 / 0,008,000,000B / 8MB
LUN 2 (Boot B):
Block size: 0x1000
Size: 0x800000 / 0,008,000,000B / 8MB
LUN 3:
Block size: 0x1000
Size: 0x2000000 / 0,032,000,000B / 32MB
LUN 4:
Block size: 0x1000
Size: 0xC0000000 / 3,000,000,000B / 3GB
LUN 5:
Block size: 0x1000
Size: 0x2000000 / 0,032,000,000B / 32MB
Number of W-LUs found: 1
W-LUN 0xC4 (RPMB):
Block size: 0x100
Size: 0x1000000 / 0,016,000,000B / 16MB
Full size: 0x1DD7800000 / 119,376,000,000B / 119GB
RPMB:
Counter: 6571
Health:
Device life time method A: 0x01 (0%-10% device life time used)
Device life time method B: 0x01 (0%-10% device life time used)
Pre End of Life: 0x01 (Used less then 80% of reserved blocks)
Checking LUs for partitioning
LUN0 Have 21 partitions
Can't stop LUN0, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN1, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN2, Code: -428677518, Reason: Unknown error (-428677518)
COM14 USB\VID_05C6&PID_9008&REV_0000 Qualcomm HS-USB QDLoader 9008 (COM14)
COM4 USB\VID_1781&PID_AAAC&REV_0100&MI_00 USB Serial Device (COM4)
Failed to find resource: IDR_DSA_PEMSelected pinout: GEN2 ISP Pinout
Change EasyJTAG Pinout OK
Z3X EasyJtag Software ver. 3.8.0.10
UFS Socket Info.
Serial: 0123A862FFB9B569EE
Description: EasyJTAG UFS Socket BGA-254 by EasyJTAG 31.12.22
Identify UFS Chip.
UFS Chip Voltage: Low
Check ISP connect.
Calibrate ISP.
VCC: 2857mV
VCCQ2: 1934mV
Chip Info:
Manufacturer: HG
ProductName: CBE06-1280CHAC
SerialNumber: 770970240126002CE9C0
OemID: 0x00
Firmware Version: 11
UFS Reference Clock: 19.2MHz
UFS Version: 2.2
Maximum Number of LUs: 32
Number of LUs found: 6
LUN 0:
Block size: 0x1000
Size: 0x1D10800000 / 116,264,000,000B / 116GB
LUN 1 (Main Boot A):
Block size: 0x1000
Size: 0x800000 / 0,008,000,000B / 8MB
LUN 2 (Boot B):
Block size: 0x1000
Size: 0x800000 / 0,008,000,000B / 8MB
LUN 3:
Block size: 0x1000
Size: 0x2000000 / 0,032,000,000B / 32MB
LUN 4:
Block size: 0x1000
Size: 0xC0000000 / 3,000,000,000B / 3GB
LUN 5:
Block size: 0x1000
Size: 0x2000000 / 0,032,000,000B / 32MB
Number of W-LUs found: 1
W-LUN 0xC4 (RPMB):
Block size: 0x100
Size: 0x1000000 / 0,016,000,000B / 16MB
Full size: 0x1DD7800000 / 119,376,000,000B / 119GB
RPMB:
Counter: 6571
Health:
Device life time method A: 0x01 (0%-10% device life time used)
Device life time method B: 0x01 (0%-10% device life time used)
Pre End of Life: 0x01 (Used less then 80% of reserved blocks)
Checking LUs for partitioning
LUN0 Have 21 partitions
Can't stop LUN0, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN1, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN2, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN3, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN4, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN5, Code: -428677518, Reason: Unknown error (-428677518)
Read USERDATA from LUN0.
Can't start LUN0, Code: -428677518, Reason: Unknown error (-428677518)
Done.
ound 2 serial devices
COM14 USB\VID_05C6&PID_9008&REV_0000 Qualcomm HS-USB QDLoader 9008 (COM14)
COM4 USB\VID_1781&PID_AAAC&REV_0100&MI_00 USB Serial Device (COM4)
Failed to find resource: IDR_DSA_PEMSelected pinout: GEN2 ISP Pinout
Change EasyJTAG Pinout OK
Z3X EasyJtag Software ver. 3.8.0.10
UFS Socket Info.
Serial: 0123A862FFB9B569EE
Description: EasyJTAG UFS Socket BGA-254 by EasyJTAG 31.12.22
Identify UFS Chip.
UFS Chip Voltage: Low
Check ISP connect.
Calibrate ISP.
VCC: 2857mV
VCCQ2: 1934mV
Chip Info:
Manufacturer: HG
ProductName: CBE06-1280CHAC
SerialNumber: 770970240126002CE9C0
OemID: 0x00
Firmware Version: 11
UFS Reference Clock: 19.2MHz
UFS Version: 2.2
Maximum Number of LUs: 32
Number of LUs found: 6
LUN 0:
Block size: 0x1000
Size: 0x1D10800000 / 116,264,000,000B / 116GB
LUN 1 (Main Boot A):
Block size: 0x1000
Size: 0x800000 / 0,008,000,000B / 8MB
LUN 2 (Boot B):
Block size: 0x1000
Size: 0x800000 / 0,008,000,000B / 8MB
LUN 3:
Block size: 0x1000
Size: 0x2000000 / 0,032,000,000B / 32MB
LUN 4:
Block size: 0x1000
Size: 0xC0000000 / 3,000,000,000B / 3GB
LUN 5:
Block size: 0x1000
Size: 0x2000000 / 0,032,000,000B / 32MB
Number of W-LUs found: 1
W-LUN 0xC4 (RPMB):
Block size: 0x100
Size: 0x1000000 / 0,016,000,000B / 16MB
Full size: 0x1DD7800000 / 119,376,000,000B / 119GB
RPMB:
Counter: 6571
Health:
Device life time method A: 0x01 (0%-10% device life time used)
Device life time method B: 0x01 (0%-10% device life time used)
Pre End of Life: 0x01 (Used less then 80% of reserved blocks)
Checking LUs for partitioning
LUN0 Have 21 partitions
Can't stop LUN0, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN1, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN2, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN3, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN4, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN5, Code: -428677518, Reason: Unknown error (-428677518)
Read USERDATA from LUN0.
Can't start LUN0, Code: -428677518, Reason: Unknown error (-428677518)
Done.
Can't start LUN4, Code: -428677518, Reason: Unknown error (-428677518)
Can't start LUN5, Code: -428677518, Reason: Unknown error (-428677518)
Read USERDATA from LUN0.
Can't start LUN0, Code: -428677518, Reason: Unknown error (-428677518)
Done.
UFS Manufacturer: HG, UFS ProductName: CBE06-1280CHAC
UFS Version: 2.2, UFS OemID: 0x00, UFS FirmVersion: 110, UFS SerialNumber: 770970240126002CE9C0
Maximum Number of LUs: 32, Number of LUs found: 6, Number of WLUs found: 1, LUs Re-configure: Enabled
UFS Version: 2.2, UFS OemID: 0x00, UFS FirmVersion: 110, UFS SerialNumber: 770970240126002CE9C0
Maximum Number of LUs: 32, Number of LUs found: 6, Number of WLUs found: 1, LUs Re-configure: Enabled
Thnnku chimera. ..We're proud to be the first in the world to support a wide range of new MTK-based devices from top brands like Oppo, Realme, and Vivo. The latest additions include:
Oppo Reno10 (CPH2531)
Oppo Reno11 (CPH2599)
Oppo Reno11 F (CPH2603)
Realme 11 Pro+ (RMX3741)
Realme C55 (RMX3710)
Vivo S9 (V2072A)
Vivo V21 (V2050)
Vivo V23 (V2130)
Vivo V25 (V2202)
Vivo Y02 (V2217/V2236)
Vivo Y02t (V2254)
Vivo Y03 (V2333)
Vivo Y100 (V2239)
Vivo Y15s (V2120)
Vivo Y16 (V2204)
Vivo Y17s (V2310)
Vivo Y21 (V2111)
Vivo Y21a (V2149)
Vivo Y21s (V2110)
Vivo Y22 (V2207)
Vivo Y27 (V2249)
Vivo Y28 (V2315/C2352)
Vivo Y33s (V2109)
Vivo Y36 (V2248)
Vivo Y36i (V2318A)
Vivo Y53s (V2058)
Vivo Y55 (V2127)
Vivo Y56 (V2225)
Vivo Y72 (V2041)
Enhanced MTK Repair IMEI(Patch) Procedure
You can now perform Repair IMEI(Patch) operation on the following models:
Infinix Hot 40 Pro
Infinix Smart 6
Oppo A38
Oppo Reno8 Pro+
Oukitel S115
Realme C55
Redmi Note 11S
TCL Tab 10L LTE Gen 3
Tecno Spark 20C
Vivo S18 Pro
New Video To Support Your Work
We are excited to present our new video showcasing the Chimera application.
*BOOB UPDATE*
Oppo Reno10 (CPH2531)
Oppo Reno11 (CPH2599)
Oppo Reno11 F (CPH2603)
Realme 11 Pro+ (RMX3741)
Realme C55 (RMX3710)
Vivo S9 (V2072A)
Vivo V21 (V2050)
Vivo V23 (V2130)
Vivo V25 (V2202)
Vivo Y02 (V2217/V2236)
Vivo Y02t (V2254)
Vivo Y03 (V2333)
Vivo Y100 (V2239)
Vivo Y15s (V2120)
Vivo Y16 (V2204)
Vivo Y17s (V2310)
Vivo Y21 (V2111)
Vivo Y21a (V2149)
Vivo Y21s (V2110)
Vivo Y22 (V2207)
Vivo Y27 (V2249)
Vivo Y28 (V2315/C2352)
Vivo Y33s (V2109)
Vivo Y36 (V2248)
Vivo Y36i (V2318A)
Vivo Y53s (V2058)
Vivo Y55 (V2127)
Vivo Y56 (V2225)
Vivo Y72 (V2041)
Enhanced MTK Repair IMEI(Patch) Procedure
You can now perform Repair IMEI(Patch) operation on the following models:
Infinix Hot 40 Pro
Infinix Smart 6
Oppo A38
Oppo Reno8 Pro+
Oukitel S115
Realme C55
Redmi Note 11S
TCL Tab 10L LTE Gen 3
Tecno Spark 20C
Vivo S18 Pro
New Video To Support Your Work
We are excited to present our new video showcasing the Chimera application.
*BOOB UPDATE*